• 한국해양공학회지
• /
• 제32권5호
• /
• pp.310-323
• /
• 2018

In order to protect lives and prevent large-scale injuries in the event of a fire on a ship or an offshore plant, most classification societies are strengthening their fire resistance designs of relevant cargo holds and accommodation compartments to keep flames from being transferred from a fire point to other compartments. Particularly in critical compartments, where flames should not propagate for a certain period of time, such as the A60 class division, both the airtightness and fire-resistant design of a piece passing through a bulkhead are subject to the Safety of Life at Sea Convention (SOLAS) issued by the International Maritime Organization (IMO). In order to verify the suitability of a fire-resistant design for such a penetrating piece, the fire test procedure prescribed by the Maritime Safety Committee (MSC) must be carried out. However, a numerical simulation should first be conducted to minimize the time and cost of the fire resistance test. In this study, transient thermal analyses based on the finite element method were applied to investigate the heat transfer characteristics of a bulkhead penetration piece for the A60 class compartment. In order to determine a rational bulkhead penetration piece design, the transient heat transfer characteristics according to the variation of design parameters such as the diameter, length, and material were reviewed. The verification of the design specification based on a numerical analysis of the transient heat transfer performed in this study will be discussed in the following research paper for the actual fire protection test of the A60 class bulkhead penetration piece.

• 대한기계학회논문집B
• /
• 제41권8호
• /
• pp.497-503
• /
• 2017

산소호흡기의 실질적인 개발 제작 및 안정성 파악을 위해서는 산소유동의 이론적인 연구가 필요하다. 이에 본 연구에서는 상용 해석 툴인 COMSOL 멀티피직스를 이용하여 산소호흡기의 사용시간 연장을 위한 고압용 감압기 설계를 진행하였다. 기존 감압기의 오리피스 내 핀 형태의 실린더 삽입 방법을 제안했으며, 새로 제시한 오리피스에 대해 3 mm, 6 mm 그리고 9 mm의 길이에서 유동 특성 분석 및 최적 길이를 도출하였다. 기존 감압기에서 토출되는 질량유량 0.028 kg/s 을 기준으로, 최대 감압기 입구 압력인 300 bar 경우 약 33%, 감압기 입구 압력조건인 50 bar, 75 bar 그리고 100 bar에서는 평균 32.71% 내외로 기존 질량조건을 만족하였다. 가공 용이성을 고려할 때 기존의 감압기와 길이가 동일하여 별도의 가공이 필요 없는 3 mm가 가장 적합하다고 판단된다.

• 대한치과보철학회지
• /
• 제44권2호
• /
• pp.185-196
• /
• 2006

Statement of problem: The researches on the influence of design variables on the stress distribution in cortical and trabecular bones and on optimal design for implant system were limited. Purpose: The purpose of this study is to identify the sensitivities of design parameters and to suggest the optimal parameters for designing the onebody type implant system. Material and methods: Stresses arising in the implant system were obtained by finite element analysis using a three dimensional model. An onebody type implant system[Oneplant (Warrantec. Co. Ltd., Korea)] was considered in this study. Vortical load(150 N) was applied on the top of the abutment along the axial direction. The initial design variables set for sensitivity analysis were radius of fixture, numbers of micro thread, numbers of power thread, height of micro thread, future length, tapered angle of future, inclined angle of thread, width of micro thread and width of power thread. The statistical technique of Design of Experiments(DOE) was applied tn the simulation model to deduce effective design parameters on stress distributions in bones. The deduced design parameters were incorporated into a fully automated design tool which is coupled with the finite element analysis and numerical optimization to determine the optimal design parameters. Results: 1. The result of sensitivity analysis showed six design variables - radius of future, tapered angle of fixture, inclined angle of thread, numbers of power thread, numbers of micro thread and height of micro thread - were more influential than the others. 2. The optimal values of design variables can be deduced by coupling finite element analysis (FEA) and design optimization tool(DOT).

• 한국안전학회지
• /
• 제29권4호
• /
• pp.116-122
• /
• 2014

This study proposes a system reliability analysis of rack storage facilities subjected to forklift colliding events. The proposed system reliability analysis consists of two steps: the first step is to identify dominant failure modes that most contribute to the failure of the whole rack facilities, and the second step is to evaluate the system failure probability. In the first step, dominant failure modes are identified by using a simulation-based selective searching technique where the contribution of a failure mode to the system failure is roughly estimated based on the distance from the origin in the space of the random variables. In the second step, the multi-scale system reliability method is used to compute the system reliability where the first-order reliability method (FORM) is initially used to evaluate the component failure probability (failure probability of one member), and then the probabilities of the identified failure modes and their statistical dependence are evaluated, which is called as the lower-scale reliability analysis. Since the system failure probability is comprised of the probabilities of the failure modes, a higher-scale reliability analysis is performed again based on the results of the lower-scale analyses, and the system failure probability is finally evaluated. The illustrative example demonstrates the results of the system reliability analysis of the rack storage facilities subjected to forklift impact loadings. The numerical efficiency and accuracy of the approach are compared with the Monte Carlo simulations. The results show that the proposed two-step approach is able to provide accurate reliability assessment as well as significant saving of computational time. The results of the identified failure modes additionally let us know the most-critical members and their failure sequence under the complicated configuration of the member connections.

• 한국항해항만학회지
• /
• 제31권10호
• /
• pp.869-877
• /
• 2007

본 논문은 교행이 불가능한 두 대의 자동화 크레인을 운영하는 자동화 컨테이너 터미널의 장치장을 대상으로 국지적 탐색 알고리즘을 이용해 실시간 작업계획을 수립하는 방안을 제안한다. 제안방안은 실시간 제약조건을 만족시키기 위해 현재 이후 일정 시간의 작업만을 작업 계획의 대상으로 삼으며, 장치장의 동적인 작업 특성을 고려하여 새로운 작업이 요청될 때마다 작업 계획을 다시 수립한다. 또한, 교행이 불가능한 두 대의 크레인을 운영할 때 발생할 수 있는 크레인 간의 작업 부하 불균형을 해소하기 위해 작업 계획 과정에서 상대 크레인에 의한 사전 재취급과 사전 이적을 통한 두 크레인 간의 협업을 가능하게 하였다. 시뮬레이션을 이용한 실험 결과 제안 방안이 휴리스틱 방안에 비해 우수하며, 크레인 간의 협업이 작업 효율 향상에 도움이 됨을 확인하였다.

• 한국정보통신학회논문지
• /
• 제14권5호
• /
• pp.1103-1108
• /
• 2010

주파수 도약 대역확산시스템에서의 광대역 주파수 도약을 위해 주파수 합성기가 널리 이용된다. 이와 같은 주파수 도약 대역확산 송수신기에서의 도약 주파수를 발생시키는 주파수 합성기는 PLL에 의해 실현된다. 따라서 논문에서는 정교한 반송파 발생, 수신기에서의 반송파동기 등을 위해 널리 이용되는 디지털 위상고정루프를 설계하고 결과를 분석하였다. 디지털 위상비교기, 루프필터, DCO 등 디지털 위상고정루프를 구성하는 기본 요소를 소개하였다. 또한 구현된 각 구성요소에 대한 시뮬레이션 결과와 특성들에 대한 분석이 이루어 졌다. 기준입력신호와 DCO의 출력신호의 위상차에 의한 특성을 분석하였다. 루프가 고정이 되었을 때 루프필터의 N값이 이웃하는 값 사이에서 토글되는 현상을 나타내며 이는 출력신호에 위상 지터를 초래한다. 이는 DCO의 클럭인 fc를 증가시키므로 해결이 가능하다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2006년도 제37회 하계학술대회 논문집 C
• /
• pp.1657-1658
• /
• 2006

An external electrode fluorescent lamps (EEFLs) have the advantage of a long lifetime in the early stages of the study on plasma discharge, interest in the lamp continues. Studies on the operation of external electrode fluorescent lamps have focused mainly on its use of a type of high frequency (MHz). By performing high brightness using a square wave operation method with the low frequency below 100kHz, which is applied to a narrowed tube type lamp that has several mm of lamp diameter. To solve these problems of CCFL, EEFL (External Electrode Fluorescent Lamp) is introduced. Because electrode of EEFL is on the outer surface of discharge tube, the electrode is perfectly prevented from the sputtering by accelerated ions. And it is possible to drive the many CCFLs at the same time, because EEFL shows the positively resistant characteristic. But EEFL has the large non-radiative power loss in sheath. In this study the novel electrode structure was introduced in order to reduce non-radiative power loss in sheath of EEFL. The novel electrode structure comes from the idea to combine conceptually capacitive discharge with inductive discharge. Thus, this study verifies the change in the optical characteristics according to the change in electrode structure through a Maxwell's electromagnetic field simulation and examines the relationship between the change in the EEFL electrode structure and brightness by measuring the optical characteristics.

• 센서학회지
• /
• 제18권5호
• /
• pp.377-384
• /
• 2009

The ultrasonic hyperthermia for oncology has been developed and studied. The HIFU(high intensity focused ultrasound) is the most recent method to treat the tumor by using ultrasound. In this study, an insertion-type transducer for treating a prostate cancer, which can focus the ultrasonic beam mechanically and electrically, was designed and developed. The developed transducer was composed of three arrays, and each array has 32 elements. For the purpose of the mechanical focusing, both side arrays are slanted to the center array by $15^{\circ}$. With this structure, NFL(near field length) was set up as 30 mm. The PZT-4 and two matching layers were used, and the backing layer was excepted to prevent energy losses. The acoustic field analysis and the heating test were performed to evaluate the performance of developed transducer. The shape of an acoustic field, peak pressure, and acoustic pressure distribution were compared with numerical simulation. The NFL was 32 mm, the beam width was 5 mm, focal area was $40\;mm^2$, and peak pressure was 5.5 MPa. With heating by using developed transducer, the temperature increased up to $33^{\circ}C$ at focal zone. As a result of this study, the usefulness of suggested transducer for prostate cancer hyperthermia was confirmed by the acoustic field analysis and the heating test with TMM(tissue mimicking) phantom.

• 전기학회논문지
• /
• 제63권10호
• /
• pp.1485-1490
• /
• 2014

$SF_6$ gas has been used for power transformers or gas insulated switchgears, because it has the superior insulation property and the stable structure chemically. It has been, however, one of global warming gases and required to reduce the its amount. Some papers have reported that its amount could be reduced by mixing with other gases, such as $N_2$, $CF_4$, $CO_2$ and $C_4F_8$ and their mixture gases would cause the synergy effect. In this paper, we investigated the characteristics of DC plasmas on $SF_6$ mixture gases with $N_2$ at atmospheric pressure. $N_2$ gas is one of cheap gases and has been reported to show the synergy effect with mixing $SF_6$ gas, even though $N_2$ plasmas have electron-positive characteristics. 38 kinds of $SF_6/N_2$ plasma particles, which consisted of an electron, two positive ions, five negative ions, 30 excitation and vibration particles, were considered in a one dimensional fluid simulation model with capacitively coupled plasma chamber. The results showed that the joule heating of $SF_6/N_2$ plasmas was mainly caused by positive ions, on the other hand electrons acted on holding the $SF_6/N_2$ plasmas stably. The joule heating was strongly generated near the electrodes, which caused the increase of neutral gas temperature within the chamber. The more $N_2$ mixed-ratio increased, the less joule heating was. And the power consumptions by electron and positive ions increased with the increase of $N_2$ mixed-ratio.

• Journal of Electrical Engineering and Technology
• /
• 제9권2호
• /
• pp.452-460
• /
• 2014

Due to increased concerns for rising oil prices and environmental problems, various solutions have been proposed for solving energy problems through tightening environmental regulations such as those regarding $CO_2$ reduction. Among them, Electrical Vehicles (EVs) are evaluated to be the most realistic and effective approach. Accordingly, research and development on EVs and charging infrastructures are mainly proceeding in developed countries. Since EVs operate using electric energy form a battery, they must be connected to the power system to charge the battery. If many EVs are connected during a short time, power quality problems can occur such as voltage sag, voltage unbalance and harmonics which are generated from power electronics devices. Therefore, when EVs are charged, it is necessary to analyze the effect of power quality on the distribution system, because EVs will gradually replace gasoline vehicles, and the number of EVs will be increased. In this paper, a battery for EVs and a PWM converter are modeled using an ElectroMagnetic Transient Program (EMTP). The voltage sag and unbalance are evaluated when EVs are connected to the distribution system of the Korea Electric Power Corporation (KEPCO). The simulation results are compared with IEEE standards.