• Imaging Science in Dentistry
• /
• v.40 no.4
• /
• pp.155-158
• /
• 2010

Digital radiographic systems allow the implementation of a fully digital picture archiving and communication system (PACS), and provide the greater dynamic range of digital detectors with possible reduction of X-ray exposure to the patient. This article reviewed the basic physical principles of digital radiographic imaging system in dental clinics generally. Digital radiography can be divided into computed radiography (CR) and direct radiography (DR). CR systems acquire digital images using phosphor storage plates (PSP) with a separate image readout process. On the other hand, DR systems convert X-rays into electrical charges by means of a direct readout process. DR systems can be further divided into direct and indirect conversion systems depending on the type of X-ray conversion. While a direct conversion requires a photoconductor that converts X-ray photons into electrical charges directly, in an indirect conversion, lightsensitive sensors such as CCD or a flat-panel detector convert visible light, proportional to the incident X-ray energy by a scintillator, into electrical charges. Indirect conversion sensors using CCD or CMOS without lens-coupling are used in intraoral radiography. CR system using PSP is mainly used in extraoral radiographic system and a linear array CCD or CR sensors, in panoramic system. Currently, the digital radiographic system is an important subject in the dental field. Most studies reported that no significant difference in diagnostic performance was found between the digital and conventional systems. To accept advances in technology and utilize benefits provided by the systems, the continuous feedback between doctors and manufacturers is essential.

• Journal of IKEEE
• /
• v.5 no.1 s.8
• /
• pp.111-120
• /
• 2001

VC merging involves distinguishing cells from an identical merged VC label. Various approaches have been proposed to help this identification process. However, most of them incur additional buffering, protocol overhead and/or variable delay. They make the provision of QoS difficult to achieve. So it was proposed a merge capable scheduler to support VC-merging (VCMS). However, in situations where all VCs are to be merged or the incoming traffic load is very low, it could happen that there are not enough non-merging cells to snoop. In this situation the scheduler uses special control cells to fill the empty time slots out. Too many control cells can cause high cell loss ratio and an additional packet transfer delay. To overcome the drawbacks, we propose a Sequence Skipping(SS) method where the sequencers skip the empty queues and insert SS cells. We show SS method is suitable for VC-merging and can reduce the cell loss ratio and the mean packet transfer delay through simulations.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.20 no.2
• /
• pp.343-350
• /
• 2016

A secure and effective on-chip bus for detecting and preventing malicious attacks by infected IPs is presented in this paper. Most system inter-connects (on-chip bus) are vulnerable to hardware Trojan (Malware) attack because all data and control signals are routed. A proposed secure bus with modifications in arbitration, address decoding, and wrapping for bus master and slaves is designed using the Advanced High-Performance and Advance Peripheral Bus (AHB and APB Bus). It is implemented with the concept that arbiter checks share of masters and manage infected masters and slaves in every transaction. The proposed hardware is designed with the Xilinx 14.7 ISE and verified using the HBE-SoC-IPD test board equipped with Virtex4 XC4VLX80 FPGA device. The design has a total gate count of 39K at an operating frequency of 313MHz using the $0.13{\mu}m$ TSMC process.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2015.10a
• /
• pp.503-506
• /
• 2015

In accordance with IoT(Internet of Things) commercialization, the need to design SoC-based hardware platform with wireless communication is increasing. This paper therefor proposes an SoC platform architecture with Smart Frame System inter-communicating between devices. Wireless communication functions and high-performance real-time image processing hardware structure was applied to existing digital photo frame. We developed a smart phone application to control the smart frame through Bluetooth communication. The SoC platform hardware consists of CIS controller, Memory controller, ISP(Image Signal Processing) module for image scaling, Bluetooth Interface for inter-communicating between devices, VGA/TFT-LCD controller for displaying video. The Smart Frame System to support the IoT services was implemented and verified using HBE-SoC-IPD test board equipped with Virtex4 XC4VLX80 FPGA. The operating frequency is 54MHz.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2015.10a
• /
• pp.861-862
• /
• 2015

In this paper we present a low area 12-bit SAR ADC (Successive Approximation Register Analog-to-Digital Converter). The proposed circuit is fabricated using Magnachip/SK Hynix 1-Poly 6-Metal $0.18-{\mu}m$ CMOS process, and it is powered by a 1.8-V supply. Total chip area is reduced by replacing the MIM capacitors with MOS capacitors instead of the capacitors consisting of overall part in chip area. The proposed circuit showed improved power dissipation of 1.9mW, and chip area of $0.45mm^2$ as compared to conventional research results at the power supply of 1.8V. The designed circuit also showed high SNDR (Signal-to-Noise Distortion Ratio) of 70.51dB, and excellent effective number of bits of 11.4bits.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2015.10a
• /
• pp.885-888
• /
• 2015

A secure and effective on-chip bus for detecting and preventing malicious attacks by infected IPs is presented in this paper. Most system inter-connect (on-chip bus) are vulnerable to hardware Trojan (Malware) attack because all data and control signals are routed. A proposed secure bus with modifications in arbitration, address decoding, and wrapping for bus master and slaves is designed using the Advanced High-Performance and Advance Peripheral Bus (AHB and APB Bus). It is implemented with the concept that arbiter checks share of masters and manage infected masters and slaves in every transaction. The proposed hardware is designed with the Xilinx 14.7 ISE and verified using the HBE-SoC-IPD test board equipped with Virtex4 XC4VLX80 FPGA device. The design has a total gate count of 40K at an operating frequency of 250MHz using the $0.13{\mu}m$ TSMC process.

• Journal of Power Electronics
• /
• v.16 no.3
• /
• pp.1226-1235
• /
• 2016

For wearable health monitoring systems, a fundamental problem is the limited space for storing energy, which can be translated into a short operational life. In this paper, a highly efficient active voltage doubling rectifier with a wide input range for micro-piezoelectric energy harvesting systems is proposed. To obtain a higher output voltage, the Dickson charge pump topology is chosen in this design. By replacing the passive diodes with unbalanced-biased comparator-controlled active counterparts, the proposed rectifier minimizes the voltage losses along the conduction path and solves the reverse leakage problem caused by conventional comparator-controlled active diodes. To improve the rectifier input voltage sensitivity and decrease the minimum operational input voltage, two low power common-gate comparators are introduced in the proposed design. To keep the comparator from oscillating, a positive feedback loop formed by the capacitor C is added to it. Based on the SMIC 0.18-μm standard CMOS process, the proposed rectifier is simulated and implemented. The area of the whole chip is 0.91×0.97 mm², while the rectifier core occupies only 13% of this area. The measured results show that the proposed rectifier can operate properly with input amplitudes ranging from 0.2 to 1.0V and with frequencies ranging from 20 to 3000 Hz. The proposed rectifier can achieve a 92.5% power conversion efficiency (PCE) with input amplitudes equal to 0.6 V at 200 Hz. The voltage conversion efficiency (VCE) is around 93% for input amplitudes greater than 0.3 V and load resistances larger than 20kΩ.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2007.08a
• /
• pp.1005-1008
• /
• 2007

In this study, an architecture for 262K-color TFT-LCD source driver. In this paper proposed the chip consumes smaller area and static current which is suitable for QVGA resolutions. In the conventional structures, all of them need large number of OPAMP buffers to drive the pixels, Therefore, highly resistive R-DACs are needed to generate gamma voltages to reduce the static current. In this study, our design only used two OPAMPs and low resistance RDACs without increasing the quiescent current. Thus, it was experted that chip would be more in consuming lower static power for longer battery lifetime. The source driver were implemented by the 3.3 V $0.35\;{\mu}m$ CMOS technology provided by TSMC. The area of the core OPAMP circuit was about $110\;{\mu}m\;{\times}\;150\;{\mu}m$ and that of the source driver was $880\;{\mu}m\;{\times}\;430\;{\mu}m$. As compared to the conventional structure, approximately 64.48 % in area was achieved.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.19 no.12
• /
• pp.2409-2417
• /
• 1994

The ODR(orthogonal double-rotation) digital lattice filters have desirable properties for VLSI implementation such as local connection, regularity and pipelinability. These filters are also known to exhibit good numerical behavior for finite precision implementation. Although these filters can be pipelined by the cut-set localization procedure, it should be noted that the maximum sample rate obtained by this technique is limited by the feedback computations. In this paper, a pipelining method for the ODR digital lattice filter is proposed, by which the sample rate can be increased at any desired level. it is also shown that the low-power CMOS digital implementation of ODR digital lattice filters can be done successfully using our pipelining method. The pipelining method is based on the properties of the Schur algoithm, constrained filter design methods, and the polyphase decomposition technique.

• ETRI Journal
• /
• v.42 no.5
• /
• pp.781-789
• /
• 2020

In this study, an E-band low-noise amplifier (LNA) monolithic microwave integrated circuit (MMIC) has been designed using silicon-germanium 130-nm bipolar complementary metal-oxide-semiconductor technology to suppress unwanted signal gain outside operating frequencies and improve the signal gain and noise figures at operating frequencies. The proposed impedance-controllable filter has series (R_s) and parallel (R_p) resistors instead of a conventional inductor-capacitor (L-C) filter without any resistor in an interstage matching circuit. Using the impedance-controllable filter instead of the conventional L-C filter, the unwanted high signal gains of the designed E-band LNA at frequencies of 54 GHz to 57 GHz are suppressed by 8 dB to 12 dB from 24 dB to 26 dB to 12 dB to 18 dB. The small-signal gain S₂₁ at the operating frequencies of 70 GHz to 95 GHz are only decreased by 1.4 dB to 2.4 dB from 21.6 dB to 25.4 dB to 19.2 dB to 24.0 dB. The fabricated E-band LNA MMIC with the proposed filter has a measured S₂₁ of 16 dB to 21 dB, input matching (S₁₁) of -14 dB to -5 dB, and output matching (S₂₂) of -19 dB to -4 dB at E-band operating frequencies of 70 GHz to 95 GHz.