• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.48 no.4
• /
• pp.39-50
• /
• 2011

In this paper, we presents a CDR circuit for $2^{nd}$-generation AiPi+, one of the Intra-panel Interface. The speed of the proposed clock and data recovery is increased to 1.25 Gbps compared with that of AiPi+. The DLL-based CDR architecture is used to generate the multi-phase clocks. We propose the simple scheme for frequency detector (FD) to mitigate the harmonic-locking and reduce the complexity. In addition, the duty cycle corrector that limits the maximum pulse width is used to avoid the problem of missing clock edges due to the mismatch between rising and falling time of VCDL's delay cells. The proposed CDR is implemented in 0.18 um technology with the supply voltage of 1.8 V. The active die area is $660\;{\mu}m\;{\times}\;250\;{\mu}m$, and supply voltage is 1.8 V. Peak-to-Peak jitter is less than 15 ps and the power consumption of the CDR except input buffer, equalizer, and de-serializer is 5.94 mW.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.15 no.3
• /
• pp.404-416
• /
• 2015

Small-area, low-power coarse and fine frequency detectors (FDs) are proposed for an adaptive bandwidth referenceless CDR with a wide range of input data rate. The coarse FD implemented with two flip-flops eliminates harmonic locking as long as the initial frequency of the CDR is lower than the target frequency. The fine FD samples the incoming input data by using half-rate four phase clocks, while the conventional rotational FD samples the full-rate clock signal by the incoming input data. The fine FD uses only a half number of flip-flops compared to the rotational FD by sharing the sampling and retiming circuitry with PLL. The proposed CDR chip in a 65-nm CMOS process satisfies the jitter tolerance specifications of both USB 3.0 and USB 3.1. The proposed CDR works in the range of input data rate; 2 Gb/s ~ 8 Gb/s at 1.2 V, 4 Gb/s ~ 11 Gb/s at 1.5 V. It consumes 26 mW at 5 Gb/s and 1.2 V, and 41 mW at 10 Gb/s and 1.5 V. The measured phase noise was -97.76 dBc/Hz at the 1 MHz frequency offset from the center frequency of 2.5 GHz. The measured rms jitter was 5.0 ps at 5 Gb/s and 4.5 ps at 10 Gb/s.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.24 no.6A
• /
• pp.871-880
• /
• 1999

In this paper, a pseudo-noise(PN) tracking and demodulation circuits are analyzed and designed for a direct-sequence/spread-spectrum multiple access system under a mobile fading channel. We consider noncoherent delay locked loop(DLL) as a PN code tracking loop which has 1/8 PN chip resolution. The tracking performance of DLL is evaluated in terms of locking time from a loose state and tracking jitter. The received signal is demodulated to original data by despreading with PN code locked by DLL. Also the designed circuit supports sound service of 32Kbps and in-band signal with 4.096MHz chip clock. The circuits are implemented and verified with FPGA, which is shown completely data recovery under AWGN 7dB and will be available for IMT-2000.

• Journal of the Korean Institute of Telematics and Electronics C
• /
• v.35C no.9
• /
• pp.11-20
• /
• 1998

High-speed complex-number arithmetic units are essential to baseband signal processing of modern digital communication systems such as channel equalization, timing recovery, modulation and demodulation. In this paper, a new complex-number multiplication algorithm is proposed, which is based on redundant binary (RB) arithmetic combined with radix-4 Booth recoding scheme. The proposed algorithm reduces the number of partial product by one-half as compared with the conventional direct method using real-number multipliers and adders. It also leads to a highly parallel architecture and simplified circuit, resulting in high-speed operation and low power dissipation. To demonstrate the proposed algorithm, a prototype complex-number multiplier-accumulator (CMAC) core with 10-bit operands has been designed using 0.8-$\mu\textrm{m}$ N-Well CMOS technology. The designed CMAC core contains about 18,000 transistors on the area of about 1.60 ${\times}$ 1.93 $\textrm{mm}^2$. The functional and speed test results show that it can operate with 120-MHz clock at V$\sub$DD/=3.3-V, and its power consumption is given to about 63-mW.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.45 no.1
• /
• pp.50-55
• /
• 2008

In this paper, New LC VCO with $8{\sim}10.9$ GHz Band has been designed using commercial $0.35-{\mu}m$ CMOS technology. This proposed circuit is consisted of the parallel construction of the typical NMOS and PMOS cross-coupled pair which is based on the LC tank, MOS cross-coupled pair which has same tail current of complementary NMOS and PMOS, and output buffer. The designed LC VCO, which is according to proposed structure in this paper, takes a 29% improvement of the wide tuning range as 8 GHz to 10.9 GHz, and a 6.48mW of low power dissipation. Its core size is $270{\mu}m{\times}340{\mu}m$ and its phase noise is as -117dBc Hz and -137dBc Hz at 1-MHz and 10-MHz offset, respectively. FOM of the new proposed LC VCO gets -189dBc/Hz at a 1-MHz offset from a 10GHz center frequency. This design is very useful for the 10Gb/s clock generator and data recovery integrated circuit(IC) and SONET communication applications.