• Journal of Welding and Joining
• /
• 제17권2호
• /
• pp.66-75
• /
• 1999

Weld bead quality in tailored blank(TB) is critically affected by edge preparation of sheets. The edge quality of prepared sheets for TB can be classified into straightness and the cross section quality of sheared plane such as a ratio of shear face, shear plane angle, etc. In order to have a good edg quality for butt-welding sheets, precision shearing will be recommended. In this paper, the feasibility of a conventional mechanical shearing as the edge preparation for tailored blanks is studyied. It reveals that fine shearing may not be the unique solution as it is generally accepted. To obtain the good shearing condition with a conventional mechanical shearing, experiments were carried out using Tahuchi method. The major parameters affecting a sheared contour are the clearance between upper blade and lower blade, and shear angle. The optimal shearing condition yields a very good straightness along the entire length of the cut, which gives a butt joint gap less than 10% of the base material thickness. The good cross section of sheared plane is also achieved in the optimal shearing condition such as a ratio of the shear face above 65%, a cross section's shear plane angle above 85%, little burr, which is providing finally good weld beads.

• 한국운동역학회지
• /
• 제19권4호
• /
• pp.761-770
• /
• 2009

이 연구는 엘리트 110m 허들선수의 세 번째 허들 넘는 동작에 관한 자세의 기술적 특징을 운동학적으로 비교분석하였다. 연구대상자는 국내에서 개최된 110m 허들의 제3회 국제육상경기대회에서 상위 입상한 전 세계기록 보유자인 국외선수 2명과 국내선수 1명으로 선정하였다. 허들을 넘는 동작인 허들링 동작의 자세에 대한 기술적 요인을 분석하기 위해 신체분절의 각도를 조사한 결과 다음과 같은 결론을 얻었다. 국외선수는 국내선수에 비해 도약과 착지 순간 신체중심각도가 전 세계기록 보유자인 국외선수는 평균 $34.14^{\circ}$, 국내선수는 $24.89^{\circ}$로 신체중심각도의 이동범위가 크게 나타났다. 상체전경각도는 도약과 착지 순간 전 세계기록 보유자인 국외선수가 $4.27^{\circ}$, 국내선수가 $6.37^{\circ}$로 전 세계기록 보유자인 국외선수 상체의 상하 움직임이 작은 것으로 나타났고, 상체좌우각도는 도약과 착지 순간전 세계기록 보유자인 국외선수가 $3.18^{\circ}$, 국내선수가 $11.58^{\circ}$로 전 세계기록 보유자인 국외선수 상체의 좌우 움직임이 작은 것으로 나타났다.

• 대한방사선치료학회지
• /
• 제16권2호
• /
• pp.63-67
• /
• 2004

목적 : 방사선치료가 발전함에 따라 3D-CRT나 IMRT 등의 새로운 치료기법이 등장하게되었다. 이러한 치료법은 여러 방향의 방사선조사를 필요로 한다. 그러나 지금의 선형가속기만으로는 사실상 여러 방향의 방사선조사에 많은 제약이 따른다. 본원에서는 이러한 장치적제한을 극복하고 궁극적으로 다양한 방향의 선속을 이용함으로서 선량분포를 개선하고자 두경부고정장치를 제작하였다. 이에 기존의 고정장치에 비해 치료기의 가동범위가 얼만큼 효율적으로 개선되었는지를 정량적으로 측정하여 조사하였다. 대상 및 방법 : 선형가속기 Couch에 기존의 고정장치를 놓고 Gantry를 각각 $45^{\circ},\;90^{\circ},\;135^{\circ}$에서 고정시키고 Couch를 돌려 장비의 clearance를 확인한다. 또한 Couch를 $0^{\circ},\;45^{\circ},\;90^{\circ}$에서 고정시키고 Gantry의 clearance를 확인한 후 제작된 Extended Head Holder(EHH)를 Couch에 부착하고 다시 앞에서 시행한 방법과 동일한 과정을 반복함으로서 EHH부착 후의 Gantry와 Couch사이의 clearance의 개선여부를 확인한다. 결과 : Gantry를 고정하고 Couch를 회전시켜본 결과 $45^{\circ}$에서는 큰 차이가 없었으나 $90^{\circ},\;135^{\circ}$로 각도가 커질수록 EHH를 사용한 경우 Couch의 가동범위가 커지는 것으로 나타났으며, Couch를 고정시키고 Gantry를 회전시킨 경우는 $45^{\circ}$에서 EHH를 사용한 경우가 사용하지 않을 경우보다 가동범위가 크게 나타나는 것을 볼 수 있었고 $0^{\circ}$와 $90^{\circ}$에서는 모두다 양호한 가동상태를 보여주었다. 또한 방사선의 후방조사시 EHH의 사용으로 Couch의 frame에 의한 방사선 감쇄를 막을 수 있었다. 결과 : 두경부환자의 치료 시 환자고정기구(EHH)를 제작하여 사용함으로서 보다 많은 방향에서 방사선조사가 가능해지고 이로 인해 보다나은 치료계획을 세울 수 있게 되었으며, 치료장비의 회전에 따른 장비와 환자사이 또는 장비와 장비사이의 안전공간이 보다 많이 확보될 수 있었다. 그리고 외국의 제품에 비해 저렴한 가격으로 제작이 가능하였고 또한 치료소모품의 절약을 가져올 수가 있게 되었다.

• 방사선산업학회지
• /
• 제17권1호
• /
• pp.1-9
• /
• 2023

Since a large amount of radioactive waste is expected to be generated due to permanent shutdown of many nuclear power plants, it is necessary to prepare efficient management methods for radioactive waste. Therefore, there is a need for a based study to apply the In-Situ gamma spectrometry, which can simplify the measurement procedure. The purpose of this study is to analyze research cases of In-Situ gamma spectrometry and to analyze the sensitivity of measurement according to influencing factors on In-Situ gamma spectrometry. Research cases of five institutions, including the CERN and the Imperial College Reactor Centre (ICRC), were selected as the institutions to be investigated. Research on the In-Situ gamma spectrometry was conducted on the satisfaction of the acceptance criteria for radioactive waste and the analysis of residual radioactivity in the site. In-Situ Objective Counting System (ISOCS) was used as a major measuring device. Sampling and computer code were used to verify the analysis results. For evaluation of measuring sensitivity according to influencing factors on In-Situ gamma spectrometry, the thickness of the measurement target, the distance between the detector and the target, the angle of the collimator, and the contamination location were performed using ISOCS's Geometry Composer. In every case, based on 122 keV, the efficiency decreased as the energy increased in the high energy region, and the efficiency decreased as the energy decreased in the low energy region. As the target thickness increased, the efficiency decreased, and as the distance between target and detector increased, the efficiency decreased. As the distance between contamination and detector increased, the efficiency decreased, and as the angle of the collimator increased, the measurement efficiency increased. However, when simulating the measurement situation using Geometry Composer, the background is not considered, and the probability of incident in the background increases as the angle increases, so further research needs to be conducted in consideration of these. This study can be utilized when applying the In-Situ gamma spectrometry of radioactive waste clearance in the future.

• 조명전기설비학회논문지
• /
• 제21권5호
• /
• pp.112-119
• /
• 2007

가공송전 도체는 정상 동작조건 하에서 전력회사의 선로 설계지침에 규정된 지상고를 안정범위 내에서 항상 유지할 수 있어야 한다. 따라서 새로운 선로를 건설하거나 노화도체의 장력을 다시 조정하거나 또는 전력용량을 최대화하기 위해 동적송전용량을 모니터링하는 경우에, 도체 이도를 측정/또는 모니터링하는 것은 매우 중요하다. 본 연구에서는 도체의 카테너리 각도로 이도 및 장력을 추정하기 위한 새로운 방법을 제안한다. 가공송전선로의 대부분의 도체들은 전형적인 카테너리 곡선을 나타내므로 철탑 측의 카테너리 각도로부터 도체의 카테너리 곡선을 유일하게 결정할 수 있다. 이 카테너리 곡선을 토대로 도체의 이도나 수평장력을 쉽게 추정할 수 있다. 몇 가지 시뮬레이션과 간단한 실험 결과를 통하여 제안된 방법이 가공송전선의 도체 이도와 장력을 측정/또는 모니터링하는데 효과적으로 사용될 수 있음을 확인하였다.

• 한국운동역학회지
• /
• 제21권5호
• /
• pp.561-571
• /
• 2011

The purpose of this study was to perform the kinematic analyses of the women's pole vault skills in IAAF World Championships Daegu 2011. Subjects were the 1st through 8th place finishers in the pole vault. The kinematic analyses were divided into four phases: two dimensional run up analysis, and three dimensional analyses for the remaining plant, swing up, and extension phases. Run-up variables consisted of run up distance, number of steps, average step length, ratio of step length to height, average velocity at the final 5~10 m, approach position. Three variables were analyzed during plant: pole angle, center of gravity (COG) velocity, and COG takeoff angle. Swing up phase variables included: pole flection angle, COG velocity (horizontal, vertical, resultant), COG trajectory and bar approach angle of COG. Compared to the 2009 World Championships in Berlin, the average vault height increased, while run up velocity and approach position were almost unchanged. However, horizontal velocity during the last two steps of the final approach decreased noticeably compared to speeds from 1990. These results reflect the change in both technique and physical fitness in pole vaulters. During extension, the peak height of COG surpassed the clearance height by an average of 0.11m. These specific results can help coaches and athletes modify training and improve performance.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2005년도 학술대회 논문집 정보 및 제어부문
• /
• pp.261-263
• /
• 2005

In this paper, we implement an identification system using the vein image of the hand. The vein pattern is obtained in the grey-scale 2D image through the infrared-red imaging from back of the hand. Since the frame has lack of clearance, we use some enhancing methods such as the complement, addition, and multiplication to the image to increase the contrast. After Wiener filtering for smoothness of the vein pattern, we transform the image into the binary image with mean function. The binarized image is session thinned and the cross-points in the vein tree are obtained by calculating the number of pixels connected because the image is shaped as a tree. We choose the point and find the nearest to the center if it has majority, where we find the two end points of the selected line. We can get the angle between the two lines joined at the cross-point and store its coordinates, angle, and label the values. The values are used as the feature vector of the vein pattern. This procedure is similar to the human cognition sequences. It is shown that the proposed method is simple for the vein recognition.

• 한국기계가공학회지
• /
• 제15권4호
• /
• pp.118-124
• /
• 2016

In this paper, the model to develop the forming process for turbine seal is suggested. And numerical approach for the shape design of the turbine seal is examined. Because of the thin thickness of the turbine seal, the seal is easily fractured in the manufacturing process. The main factors of the seal manufacturing consist of addendum angle and dedendum angle, fillet on the addendum face, number of the gear teeth, sheet initial location and gear initial location, rake and vertical clearance. The structure and shape of seal are modeled using the commercial 3D mechanical design program, CATIA(V5/R20). Also, rolling process to manufacture the turbine seal is analyzed using DEFORM$^{TM}$-3D(V11), commercial forming analysis software and runs under PC workstation. This study focused on the shape design of turbine seal. Through this research, the main factors to make the turbine seal for airplane turbine engine can be obtained. This study results are reflected to the shape design for turbine seal.

• Journal of Biosystems Engineering
• /
• 제27권6호
• /
• pp.547-556
• /
• 2002

Upright positioning of garlic cloves in mechanical planting has been considered as an essential process because pose of garlic affects not only initial budding and rooting of garlics but quality and yield. Due to the geometrical uniqueness and irregularity of garlic cloves in shape, manual planting operation has been conducted. The overall objective of this research was to determine design factors for designing a garlic clove planter The results are summarized as follows : 1. A vibrating-type clove-metering device was designed and tested. Effects of tilted angle of metering plate and magnitude of vibration on metering performance were investigated. The successful planting rates of the metering device were 96.7% for Hanji varieties. 2. Clove upright-positioning device, posture inducer was designed and tested. When the clearance between the hoppers was set at 4mm, the rates of upright positioning of the device were 92.2% for with Hanji varieties. 3. Optimum metering performance was observed at the plate tilted angle of 80。 with the posture type positioning device.

• 한국자동차공학회논문집
• /
• 제15권4호
• /
• pp.47-53
• /
• 2007

A bearing is one of core parts in automobile. Rubber seal of the bearing is important to improve performance of bearing, formed by hot-press die of rubber seal for the intricate shape. In this study, formed tools are used to machine die of bearing rubber seal and the machining operation is classified into the several process of high precision. Design of experiments is used to optimize selection of the formed tools for the efficient machining of the hot-press die. The cutting force, tool wear and tool life are determined to characteristics. And, the clearance angle, the rake angle and the length cutting edge are considered as the major factors. Experiments are repeated to use one-way factorial design, and tool life is predicted by regression model.