• 대한전기학회논문지:전력기술부문A
• /
• 제54권3호
• /
• pp.133-138
• /
• 2005

This paper presents a characteristics of horizontal swing angle in V type suspension string sets for 765kV T/L. The design of V type suspension string set does not differ from that of general string set for general towers, but it prevents instabilities from swing motion by the horizontal angle and by the wind pressure. We were designed specially 6 conductor yoke, arcing horn and earth horn. And we were decided to 550mm for a distance of strings. We were carried out characteristics of horizontal swing test and movement of mass center test for V-string sets of 400kN single, 300kN double and 400kN double. This products will be used for 765kV T/L of 1 circuit in suspension towers.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2003년도 추계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.227-231
• /
• 2003

In This paper, A novel zero-voltage-switching(ZVS) resonant DC-DC converter is proposed. it is composed of two symmetrical active-clamped circuits, The converter can achieve each switchs ZVS. proposed circuit is active clamp capacitor Ratios can be reduce switching voltage stress of each main switch. Simulation results using Pspice ver 9.2 show that the prove the validity of theoretical analysis.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 1997년도 전력전자학술대회 논문집
• /
• pp.247-250
• /
• 1997

A novel zero-voltage-switching(ZVS) isolated PWM converter for single stage power factor correction (PFC) is presented to improve the performance of the previously presented ZVT converter[5]. A simple clamp circuit in the primary side provides zero-voltage-switching condition to all semiconductor devices. This ZVS is achieved with minimum device voltage and current stresses. Operation principle, control strategy and features of the proposed converter are presented and verified by the experimental results from a 1.5 ㎾, 100 KHz laboratory prototype

• 조명전기설비학회논문지
• /
• 제12권3호
• /
• pp.37-44
• /
• 1998

본 논문에서는 분산전원 장치에 사용되는 증첩형 액티브클램프 ZVS 포워드 컨버터와 ZVS 하프 브리지(Half bbridge) 컨버터의 동작특성과 효율을 비교하였다. 또한 중첩형 액티브클램프 ZVS 포워드 컨버터의 전류모드 제어회로 설계 방법을 제시하였고, 게이트 구동회로를 간단히 하기 위해 N-P M OSFETs 로 조합된 액티브클램프 기법을 제안하여 50~100% 부하 범위에서 약 90%의 효율을 얻을 수 있었다.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제52권4호
• /
• pp.183-190
• /
• 2003

We report the performance of an open-frame type low-voltage high-current DC-DC converter module developed using an active clamp forward converter circuit and current doubler rectifier. The converter module is designed with the specifications of an 1.8V output voltage, 25A output current, and 36-75V input voltage. The synchronous rectifier is used to reduce the conduction fuss at high current level and current-mode control is adapted to enhance the flexibility in the system configuration. A prototype converter module is successfully implemented within 10mm height and half brick size (58${\times}$61mm), and recorded an 84% efficiency and 4% voltage regulation for the entire input voltage range, thereby demonstrating its application potentials to future telecommunication electronics.

• 대한전기학회논문지:전력기술부문A
• /
• 제52권4호
• /
• pp.183-183
• /
• 2003

We report the performance of an open-frame type low-voltage high-current DC-DC converter module developed using an active clamp forward converter circuit and current doubler rectifier. The converter module is designed with the specifications of an 1.8V output voltage, 25A output current, and 36-75V input voltage. The synchronous rectifier is used to reduce the conduction fuss at high current level and current-mode control is adapted to enhance the flexibility in the system configuration. A prototype converter module is successfully implemented within 10mm height and half brick size (58×61mm), and recorded an 84% efficiency and 4% voltage regulation for the entire input voltage range, thereby demonstrating its application potentials to future telecommunication electronics.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제52권9호
• /
• pp.468-474
• /
• 2003

This paper describes the development of an open frame type high power density switching converter. It is based on the active clamp forward converter with synchronous rectifier, and packaged by using the open frame and multi-layer printed circuit board (PCB) technology to achieve the higher power density. Furthermore, the windings of transformer and inductor are also realized by multi-layer PCB so that it also contributes to achieve higher power density. Through the experiment on the prototype converter of 50[W], it is confirmed that power density of 50[W/i$n_3$] and maximum efficiency of over 91[%] are obtained.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 하계학술대회 논문집 G
• /
• pp.3184-3186
• /
• 1999

In this paper, a new structure of fully differential delay cell VCO using quadrature phase for low phase noise and high speed operation is suggested. It is realized by inserting voltage clamp circuit into input pairs of delay cells that include three-control current source having high output impedance. In this reason. this newly designed delay cell for VCO has the low power supply sensitivity so that the phase noise can be reduced. The whole characteristics of VCO were simulated by using HSPICE and SABER. Simulation results show that the phase noise of new VCO is quite small compared with conventional fully differential delay cell VCO and ring oscillator type VCO. It is also very beneficial to low power supply design because of wide tuning range.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2001년도 전력전자학술대회 논문집
• /
• pp.534-537
• /
• 2001

This paper deals with the active clamp ZVS flyback converter for RF generator. The proposed converter has the characteristics of the low switching noise and high efficient regarding conventional flyback converter. To verify validity of the proposed converter, the 100kHz, 48V, 300W converter are simulation and experimental result. This converter will be apply to the discharge drive circuit for PDP(Plasma Display Panel) TV.

• Journal of Power Electronics
• /
• 제17권1호
• /
• pp.242-252
• /
• 2017

This paper deals with the blocking of DC-fault current during DC cable short-circuit conditions in HVDC (High-Voltage DC) transmission systems utilizing Modular Multilevel Converters (MMCs), where a new SubModule (SM) topology circuit for the MMC is proposed. In this SM circuit, an additional Insulated-Gate Bipolar Translator (IGBT) is required to be connected at the output terminal of a conventional SM with a half-bridge structure, hereafter referred to as HBSM, where the anti-parallel diodes of additional IGBTs are used to block current from the grid to the DC-link side. Compared with the existing MMCs based on full-bridge (FB) SMs, the hybrid topologies of HBSM and FBSM, and the clamp-double SMs, the proposed topology offers a lower cost and lower power loss while the fault current blocking capability in the DC short-circuit conditions is still provided. The effectiveness of the proposed topology has been validated by simulation results obtained from a 300-kV 300-MW HVDC transmission system and experimental results from a down-scaled HVDC system in the laboratory.