• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.58 no.8
• /
• pp.1644-1650
• /
• 2009

An improved guarding circuit is applied to a transconductance driven-right-leg circuit to decrease common-mode current at measurement electrodes due to power-line interference. After showing conventional guarding circuit is instable due to gain-peaking when used with a transconductance DRL circuit, the effect of the proposed guarding circuit modified to suppress the gain-peaking by inserting a series resistor between shields and a shield driver was analyzed. It is shown that, besides stability, the proposed guarding circuit provides two other advantages: 1) The gain of the shield driver can be set to be unit nominally. 2) The loop gain of the transconductance DRL loop can be increased due to pole-zero canceling. The proposed circuit was implemented and the advantages were confirmed.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.13 no.1
• /
• pp.1-10
• /
• 1976

A 2-out of-3 coincidence circuit and a discriminator to be used in the safely systems in nuclear reactors are described and analyzed in detail. The expressions for the reliability and the spurious scram reiliability of 1.out of-m coincidence logic in general are derived and the optimum value of 1 is assessed. The coincidence circuit is designed by making use of the pulse-summing method and is very simple in principle. The discriminator has good linearity in in the whole discrimination range and good threshold stability.

• Journal of Welding and Joining
• /
• v.14 no.5
• /
• pp.145-150
• /
• 1996

The variation of spatter generation in gas metal arc welding with welding conditions and wire compositions was investigated and interpreted in terms of arc stability. The transition range from a short circuit mode to a spray mode in the mixed gas welding showed an unstable arc and generated the largest amount of spatters. Titanium reduced spatters only in the globular mode of $CO_2$welding and silicon and manganese showed the same effect The effect of silicon and manganese, however, was no longer seen when titanium was added simultaneously to the wire. It is believed that deoxidizers easily form oxides on the anode and make the arc stable even in DCRP welding. The wires with deoxidizers also showed low short circuit frequency, resulting in the increase of large size spatters.

• Journal of Welding and Joining
• /
• v.19 no.5
• /
• pp.486-491
• /
• 2001

The effect of S content in welding wires on spattering characteristics and droplet transfer phenomena was studied. In MAG welding using 80%Ar-$20%CO_2$ shielding gas, spattering characteristics and droplet transfer phenomena were varied with S content of wire. Sulfur addition in wire reduced surface tension of droplet and weld pool, and made arc more stable in MAG welding. With increasing S content, the spattering ratio and the ratio of large size spatter ($d{\geq}1.0mm$) were reduced in short circuit transfer mode. In spray transfer mode, spattering ratio, however was increased when sulfur was added more than 0.020wt.% because surface tension of droplets and weld pool was reduced too much even though arc stability was improved.

• International Journal of Aeronautical and Space Sciences
• /
• v.7 no.1
• /
• pp.54-64
• /
• 2006

To augment weakly damped lag mode stability of a hingeless helicopter rotor blade in hover, piezoelectric shunt with a resistor and an inductor circuits for passive damping has been studied. A shunted piezoceramics bonded to a flexure of rotor blade converts mechanical strain energy to electrical charge energy which is dissipated through the resistor in the R-L series shunt circuit. Because the fundamental lag mode frequency of a soft-in-plane hingeless helicopter rotor blade is generally about 0.7/rev, the design frequency of the blade system with flexure sets to be so. Experimentally, the measured lag mode frequency is 0.7227/rev under the short circuit condition. Therefore the suppression mode of this passive damping vibration absorber is adjusted to 0.7227/rev. As a result of damping enhancement using passive control, the passive damper which consists of a piezoelectric material and shunt circuits has a stabilizing effect on inherently weakly damped lag mode of the rotor blades, at the optimum tuning and resistor condition.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.13 no.4
• /
• pp.134-141
• /
• 1999

Ths paper describes on the stability improvement of output voltage control on the power suwJy for railway. On the transient states such as input voltage sudden change, the inpJt and output voltage beccxre unstable by L-C resonance occurred due to constant output voltage control. In this paper, the new clamping circuit for system stability is proposed, and control method using band attenuated filter and feed-forward terms is introduced. The propoesd damping circuit is composed with sma1l size R-L. Also, the 3 level PWM method is adopted to decrease distortion of output voltage. The output voltage is controlledl with variation under 10% without oscillation at transient states and have total hanmnic distortion under 3%.der 3%.

• Journal of Welding and Joining
• /
• v.34 no.3
• /
• pp.40-46
• /
• 2016

The digital controlled SMA welding power source having the hot start current and short circuit waveform control was developed. The inverter power controller was used an analog circuit and the short circuit waveform controller was developed using a 8-bit MCU. For the evaluation of the developed SMA welding power source it were compared with a domestic welding power sources. Using the high titanium oxide type and low hydrogen type electrodes, the characteristics of hot start and short circuit was evaluated. Developed SMA welding power source shows good start performance. Also, arc stability and low current weldability were improved by the short circuit waveform control.

• Proceedings of the KIPE Conference
• /
• 2004.07b
• /
• pp.704-708
• /
• 2004

Recently, many nation have released standard such as IEC 61000-3-2 and IEEE 59, which impose a limit on the harmonic current drawn by equipment connected to AC line in order to prevent the distortion of an AC Line. Therefore, Plasma Display Panel (PDP) which is highlightened in digital display device also has the Power Factor Correction (PFC) circuit to meet the harmonic requirements. In PDP power module, the conventional boost converter is usually used for the PFC circuit. However, it comes serious thermal problem on it's bridge diode due to heat of PDP, and therefore the system stability is not guaranteed. In this paper, the bridgeless boost converter, which is used for PFC circuit of the PDP power module, is designed and verified the possibility of the application in a practical product in a view of efficiency, component count, temperature and etc.

• Tribology and Lubricants
• /
• v.29 no.3
• /
• pp.143-148
• /
• 2013

In this study, several sensor parts used to obtain better signal stability are designed, a separate control circuit for the sensor is developed, and the results obtained using this control circuit are analyzed. The capacitances of the whole sensor system are measured using the control circuit connected to an improved flexible printed circuit board and an asymmetric dual sensor coated with a ceramic material. To realize good discrimination for a small change in the measured capacitance as the engine oil deteriorates, a commercial application-specific integrated circuit is installed on the control circuit as a capacitance-to-digital converter. The absolute error of a measured signal is found to be approximately ${\pm}4fF$.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.25 no.5
• /
• pp.545-551
• /
• 2022

We proposed a design method for constant current pyro squib circuit. The current method using N MOSFET for the stability problem has a weakness of the current change, requiring a new design. This paper identified the problem with conventional squib circuit where the current is reduced by 25 % when maximum resistance is 3 ohms. Thus, we proposed a stable constant current driving circuit using P MOSFET and PNP BJT. We confirmed stable constant circuit operation through simulations and measurements of the proposed circuit design where the current did not change until the resistance reached 3 ohms.