• 한국정밀공학회지
• /
• 제11권6호
• /
• pp.42-49
• /
• 1994

One of the parameters that influence the productivity of every industry, involved in metal cutting, is the chip from ; continuous or broken chip. Chip form varies according to machining conditions, material used, tool geometry and chip breaker geometry. Therefore, in this study we carried out the experiment on the chip control in machining STS304 using an attached obstruction type chip breaker. Namely, with the change of a chip breaker distance, chip breaker angle, cutting characteristics in machining STS304 which is well-known as a machining difficult material and produces a saw-toothed chip. The results of the experiment are as follows : 1. The chip breaker distance and angle under which the preferred chip is produced, show 1.5mm and 60 .deg. , while chip breaker angle in machining an ordinary steel was well-known 45 .deg. . 2. During the cutting process, the change of feed than the change of velocity was applied as cutting conditions, effects more clearly on the chip breaking. 3. Considering a whole surface roughness, it is not advisable to apply chip breaker mentioned above for precision cutting.

• 한국생산제조학회지
• /
• 제9권3호
• /
• pp.48-54
• /
• 2000

In this study the characteristics of chip formation of the cold drawn Bi-S free machining steels were assessed. And for comparison those of the cold drawn Pb-S free machining steel the hot rolled low carbon steel which has MnS as free machining inclusions and the conventional steels were also investigated. During chip formation the cold drawn free machining steels show relatively little change in thickness and width of chip compare to those of the conventional carbon steels. And a single parameter which indicates the degree of deformation during chip formation chip cross-section area ratio is introduced. The chip cross-section area ratio is defined as chip cross-section area is divided by undeformed chip cross-section area. The variational patters of the chip cross-section area ratio of the materials cut are similar to those of the shear strain values. The shear stress however seems to be dependent on the carbon content of the materials. The cold drawn Bi-S and Pb-S steels show nearly the same chip forming behaviors and the energy consumed during chip formation is almost same. A low carbon steel without free machining aids shows poor chip breakability due to its high ductility. By introducing a small amount of free machining inclusions such as MnS Bi, Pb or merely increasing carbon content the chip breakability improves significantly.

• 대한기계학회논문집
• /
• 제11권6호
• /
• pp.1005-1013
• /
• 1987

For the factory automation and unmanned machine operation, it is very important to manufacture highly reliable and efficient chip breakers for optimal chip control. In this research, using the CALMA CAD/CAM SYSTEM, the manufacturing process of 3-dimensional chip breakers is established. Using the results of the cutting test of the selected chip breakers with double-step grooves, the chip breaking mechanism is schematically analysed. An expression for the chip breaking relation is derived which considers chip material behavior following LUDWIK's stress-strain curve, chip breaking criterion and the shape of chip breakers. This contains the thickness of chip, the radius of chip curl, and the mechanical properties of chip materials. It is found that the expression agrees very closely with the experimental results.

• 한국공작기계학회논문집
• /
• 제16권3호
• /
• pp.64-74
• /
• 2007

The continuous chip in turning operation deteriorates precision of workpiece and causes a hazardous condition to operator. Thus the chip form control becomes a very important task for reliable machining process. So, grooved chip breaker is widely used to obtain reliable discontinuous chip. However, developing new cutting insert having chip breaker takes long time and needs lots of research expense due to a couple of processes such as forming, sintering, grinding and coating of product and many different evaluation tests. In this paper, performance of commercial chip breaker is evaluated with neural network which is learned with a back propagation algorithm. For the evaluation, several important elements(depth of cut, land, breadth, radius) which directly influence the chip formation were chosen among commercial chip breakers and were used as input values of neural network. With the results of these input values, the performance evaluation method was developed and applied that method to the commercial tools.

• 한국안전학회지
• /
• 제9권4호
• /
• pp.17-28
• /
• 1994

Chip breaking is important in lathe work for maintaining good surface of the products and safety of operator. The purpose of this study is to investigate the performance of chip breaking and chip shape resulted from the carbide inserts with grooved type and obstruction type chip breaker. Experiments have been performed under the following cutting conditions, (1) constant cutting speed with variable depth of cut and feed rate, (2) constant depth of cut with variable cutting speed and feed rate. Also, the flying distance of chip and it's distribution have been investigated. As a results, good performance of chip breaking can be obtained for small radius of curvature and land width of grooved type chip breaker. And the thickness of chip increase with the increase of feed rate and decrease of cutting speed, and the chip breaking becomes easier with the increase of chip thickness due to the large deformation rate. Obstraction type chip breaker shows better performance of surface roughness than the grooved type. The flying distance of the chips over 90% are less than 1 meter, and the distance decreases as the feed rate decreases.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 1999년도 추계학술대회 논문집 - 한국공작기계학회
• /
• pp.351-356
• /
• 1999

In this study, the characteristics of chip formation of the cold drawn Bi-S free machining steels were assessed. And for comparison, those of the cold drawn Pb-S free machining steel, the hot rolled low carbon steel which has MnS as free machining inclusions and the conventional steels were also investigated. During chip formation, the cold drawn free machining steels show relatively little change in thickness and width of chip compare to those of the conventional carbon steels. And a single parameter which indicates the degree of deformation during chip formation, 'chip cross-section area ratio' is introduced. The chip cross-section area. The variational patterns of cross-section area is divided by undeformed chip cross-section area. The variational patterns of the chip cross-section area ratio of the materials cut are similar to those of the shear strain values. The shear stress, however, seems to be dependent on the carbon content of the materials. The cold drawn BiS and Pb-S steels show nearly the same chip forming behaviors and the energy consumed during chip formation is almost same. A low carbon steel without free machining aids shows poor chip breakability due to its high ductility. By introducing a small amount of non-metallic inclusions such as MnS, Bi, Pb or merely increasing carbon content the chip breakability improves significantly.

• 한국정밀공학회지
• /
• 제16권9호
• /
• pp.191-199
• /
• 1999

In the continuous cutting process such as turning operation, chip control is thought very important to achieve the unmanned manufacturing system. The prediction of chip breakage under the given conditions is a substantial element for chip control. In this paper, a systematic approach to know the chip breaking region is represented under the concept of equivalent parameters. to Verify the suggested model, cutting experiments are executed with a commercial type and two other type chip breakers which have modified chip breaker parameters such as land width, groove width and nose radius. predicted chip breaking regions using the 3D cutting model agrees with those obtained from the experiments.

• 조명전기설비학회논문지
• /
• 제29권1호
• /
• pp.1-8
• /
• 2015

To produce the white light, there are a single chip method using the blue light and phosphor coating, a multi chip method by mixing R, G, B light.. Multi chip method is proper for the smart lighting system by controling color and color temperature. And color rendering of single chip LED is good by even spectral distribution. To apply application technic like smart light system, this paper analyzed the properties of single chip LED and RGB multi chip LED, and implemented the 2 part subject evaluation for single chip LED and RGB multi chip LED. The first part is comparison of properties for single chip LED and RGB multi chip and second part is color appearance evaluation of 8 colors in each lighting environment.

• ETRI Journal
• /
• 제27권5호
• /
• pp.497-503
• /
• 2005

In this paper, we present a performance analysis for an MPEG-4 video codec based on the on-chip network communication architecture. The existing on-chip buses of system-on-a-chip (SoC) have some limitation on data traffic bandwidth since a large number of silicon IPs share the bus. An on-chip network is introduced to solve the problem of on-chip buses, in which the concept of a computer network is applied to the communication architecture of SoC. We compared the performance of the MPEG-4 video codec based on the on-chip network and Advanced Micro-controller Bus Architecture (AMBA) on-chip bus. Experimental results show that the performance of the MPEG-4 video codec based on the on-chip network is improved over 50% compared to the design based on a multi-layer AMBA bus.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2001년도 춘계학술대회 논문집
• /
• pp.891-894
• /
• 2001

In this work, an effort is made to investigate the behavior of a chip, from its initial flow to its final breaking stage. The expression for chip flow in grooved tools is verified analytically using FEM. Cutting parameters like velocity and depth of cut have a profound influence on chip flow behavior. Chip curling increases and, for a given tool geometry, effectiveness of the groove increases with increasing depth of cut. The feasibility of tool design using FEM simulations is also demonstrated. Optimization of tool geometry results in better chip control.