• Corrosion Science and Technology
• /
• v.15 no.2
• /
• pp.84-91
• /
• 2016

The transport and deposition of corrosion products in pressurized water nuclear reactor (PWR) steam generators have led to corrosion (SCC, denting etc.) problems. Lancing, mechanical cleaning and chemical cleaning have been used to reduce these problems. The methods of lancing and mechanical cleaning have limitations in removing corrosion products due to the structure of steam generator tubes. But high temperature chemical cleaning (HTCC) with EDTA is the most effective method to remove corrosion products regardless of the structure. However, EDTA in chemical cleaning aqueous solution and chemical cleaning environments affects the integrity of materials used in steam generators. The nuclear power plants have to perform the pre-test (also called as qualification test (QT)) that confirms the effect on the integrity of materials after HTCC. This is one of the series studies that assess the effect, and this study determines the effects of 20 % EDTA aqueous solution on defective tubes in high temperature chemical cleaning environments. The depth and magnitude of defects in steam generator (SG) tubes were measured by eddy current test (ECT) signals. Surface analysis and magnitude of defects were performed by using SEM/EDS. Corrosion rate was assessed by weight loss of specimens. The ECT signals (potential and depth %) of defective tubes increased marginally. But the lengths of defects, oxides on the surface and weights of specimens did not change. The average corrosion rate of standard corrosion specimens was negligible. But the surfaces on specimens showed traces of etching. The depth of etching showed a range on the nanometer. After comprehensive evaluation of all the results, it is concluded that 20 % EDTA aqueous solution in high temperature chemical cleaning environments does not have a negative effect on defective tubes.

• Bulletin of the Korean Chemical Society
• /
• v.25 no.2
• /
• pp.233-236
• /
• 2004

Total impurity analysis of a primary standard solution is one of the essential procedures to determine an accurate concentration of the standard solution by the gravimetry. Bi impurity is determined in Pb standard solutions by inductively coupled plasma mass spectrometry (ICP-MS). The direct nebulization of the Pb standard solution produces a significant amount of the Pb matrix-induced molecular ions which give rise to a serious spectral interference to the Bi determination. In order to avoid the spectral interference from the interferent $^{208}PbH^+$, the hydride generation method is employed for the matrix separation. The Bi hydride vapor is generated by reaction of the sample solution with 1% sodium borohydride solution. The vapor is then directed by argon carrier gas into the ICP after separation from the mixture solution in a liquid-gas separator made of a polytetrafluoroethylene membrane tube. The presence of 1000 ${\mu}$g/mL Pb matrix caused reduction of the bismuthine generation efficiency by about 40%. The standard addition method is used to overcome the chemical interference from the Pb matrix. Optimum conditions are investigated for the hydride-generation ICPMS. The detection limit of this method is 0.5 pg/mL for the sample solutions containing 1000 ${\mu}$g/mL Pb matrix.

• Journal of Powder Materials
• /
• v.19 no.3
• /
• pp.220-225
• /
• 2012

YAG:Ce yellow phosphor particles were synthesized by spray pyrolysis with changing the solution properties and their luminous properties, crystal structure, and morphological changes were studied by using PL measurement, XRD, and SEM analysis. It was clear that the solution properties significantly affected the crystal phase, crystallite size, the PL intensity, and the morphology of YAG:Ce particles. At low calcination temperature, the addition of urea only to the spray solution was helpful to form a pure YAG phase without any impurity phases, as the result, the highest luminescence intensity was achieved at the calcination temperature of $900^{\circ}C$. When the calcination temperatures were larger than $1300^{\circ}C$, however, the YAG particles prepared without any additive showed the highest luminescent intensity. Regardless of the solution conditions, the emission intensity of YAG:Ce particles prepared by spray pyrolysis showed a linear relation with the crystallite size. In terms of the morphology of YAG:Ce particles, the addition of both DCCA and $NH_4OH$ to the spray solution was effective to prepare a spherical and dense structured YAG particles.

• Journal of Information Display
• /
• v.13 no.4
• /
• pp.151-157
• /
• 2012

A simple method of fabricating out-coupling structures was demonstrated via solution-processing to enhance light extraction from organic light-emitting diodes (OLEDs). Scattering layers were easily obtained by spin-coating an $SiO_2$ sol solution that contained $TiO_2$ particles. By introducing the scattering layer and the solution-processible corrugated structure as internal and external extraction layers, the OLEDs showed increased external quantum efficiency without a change in the electroluminescence spectrum compared to conventional devices. Using these solution-processible out-coupling structures, nearly all-solution-processed OLEDs with enhanced light extraction could be fabricated. The light extraction enhancement is attributed to the suppression by the out-coupling structures of the light-trapping that arose at the interface of the glass substrate and the air.

• Current Applied Physics
• /
• v.18 no.11
• /
• pp.1300-1305
• /
• 2018

The tunable electronic performance of the solution-processed semiconductor metal oxide is of great significance for the printing electronics. In current work, transparent thin-film transistors (TFTs) with indium-zinc oxide (IZO) were fabricated as active layer by a simple eco-friendly aqueous route. The aqueous precursor solution is composed of water without any other organic additives and the IZO films are amorphous revealed by the X-ray diffraction (XRD). With systematic studies of atomic force microscopy (AFM), X-ray photoemission spectroscopy (XPS) and the semiconductor property characterizations, it was revealed that the electrical performance of the IZO TFTs is dependent on the concentration of precursor solution. As well, the optimum preparation process was obtained. The concentrations induced the regulation of the electronic performance was clearly demonstrated with a proposed mechanism. The results are expected to be beneficial for development of solution-processed metal oxide TFTs.

• Bulletin of the Korean Chemical Society
• /
• v.15 no.8
• /
• pp.685-687
• /
• 1994

• Journal of the Korean Ceramic Society
• /
• v.42 no.7 s.278
• /
• pp.521-524
• /
• 2005

ZnO 2-D nanowall structure with around 100 nm thickness, which is composed of tens of nm scale ZnO single crystals, was fabricated through the low temperature chemical solution growth method. Electro Chemical Deposition (ECD) technique was applied to attach the ZnO seed crystals on ITO coated glass substrate. The ZnO nanowall structure was grown in the 0.015 mol$\%$ of aqueous solution of zinc nitrate and hexamethenamine at 60$^{\circ}C$ for 20 - 40 h. The nanowall structure depends on the ECD condition or the applied voltage and duration time. The nanowall shows a photoluminescence around 550 - 700 nm spectrum range.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2000.05a
• /
• pp.959-962
• /
• 2000

In this study, the micro shaft was fabricated by high speed etching process. The integration of the kinetic energy of circumference and the effect of etching takes less time to fabricate the micro shaft than any other conventional methods. First, the end part of the rod(SKD11) was dipped in chemical solution(FeCl$_3$) and the rod rotated at high speed(3500-10000rpm). Experimental setup was simply composed of high speed motor. chemical solution and $\Phi$ 1 mm rod. The main factors of diameter control are chemical concentration, reaction time and rpm. has a result. the diameter of the dipped rod was decreased by 200${\mu}{\textrm}{m}$ by high speed rotation and its shape and surface was good. From this experiment, we found the possibility to manufacture micro shaft without very expensive equipment.

• Journal of the Korean Chemical Society
• /
• v.6 no.1
• /
• pp.94-98
• /
• 1962

The polycondensates of isophthalic acid-cinnamic acid-glycerine system were synthesized. The molecular weights of these products were determined by two methods, viscosity method and osmotic pressure methods. In the synthesis of resin, the reaction temperature was kept at 232$^{\circ}C$ and the mole ratio of the reactants was chosen as follows: Glycerine ;1.0 Isophthalic acid ;1.0 Cinnamic acid ;2.8 Excessive cinnamic acid prevented gelation of reaction mixtures. As the solution became very dilute, reduced osmotic pressure P/C (at the concentration of solution below 0.24g/100 ml of acetone) and reduced viscosity ${\eta}_{sp}/C$ (at the concentration of solution below 0.32 g/100 ml of acetone) increased rapidly. The correspondence between molecular weights determined by the two methods made Huggin's equation applicable to the prepared polymer. The values of K and a are $2.77{\times}10^{-5}$ and 1.063, respectively.

• 제어로봇시스템학회:학술대회논문집
• /
• 1998.10a
• /
• pp.455-460
• /
• 1998

We propose robust MILP model for scheduling and design of multiproduct batch processes in this paper. Recent stochastic modeling approaches considering uncertainty have mainly focused on maximization of expected NPV. Robust model concept is applied to generate solution spectrum in which we can select the best solution based on tradeoff between robustness measure and expected NPV. Robustness measure is represented as penalty term in the objective function, which is Upper Partial Mean of NPV. We can quantify solution robustness by this penalty term and maintain model as MILP form to be computationally efficient. An example illustrates the effectiveness of the proposed model. In many cases sufficient robustness can be guaranteed through a little reduction of expected NPV.