• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part 1
• /
• pp.405-406
• /
• 2006

Raw materials from different sources, produced by a given process and having equal chemical composition, are supposed to be equivalent. The differences in sintering behavior have been investigated on P/M steels obtained from four diffusion-bonded powders (Fe + Ni + Cu + Mo) on atomized iron base, at the same alloy contents. Two levels of carbon and two sintering conditions have been investigated. Dimensional changes, C content, hardness, microhardness pattern, universal hardness, fractal analysis, pore features, microstructure features, and rupture strength have been compared to characterize different raw materials. The results show that the claimed equivalence is not confirmed by experimental data.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2005년도 하계학술대회 논문집 Vol.6
• /
• pp.617-618
• /
• 2005

The main purpose of this study is to investigate the effect of gas pressure infiltration on microstructure. Continuous fiber reinforced Al matrix composite wire is produced by gas pressure infiltration process. With the increase of gas pressure, porosity and wettabillity was improved. No chemical reaction product was detected at the interface of $Al_2O_3$ and Al.

• 한국결정성장학회:학술대회논문집
• /
• 한국결정성장학회 2000년도 Proceedings of 2000 International Nano Crystals/Ceramics Forum and International Symposium on Intermaterials
• /
• pp.127-142
• /
• 2000

The charged cluster model states that chemical vapor deposition (CVD) begins with gas phase nucleation of charged clusters followed by cluster deposition on a substrate surface to form a thin film. A two-chambered CVD system, separated by a 1-mm orifice, was used to study gold deposition by thermal evaporation in order to determine if the CCM applies in this case. At a filament temperature of 1523 and 1773 K, the presence of nano-meter sized gold clusters was found to be positive and the cluster size and size distribution increased with increasing temperature. Small clusters were found to be amorphous and they combined with clusters already deposited on a substrate surface to form larger amorphous clusters on the surface. This work revealed that gold thin films deposited on a mica surface are the result of the sticking of 4-10 nm clusters. The topography of these films was similar to those reported previously under similar conditions.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2009년도 추계학술발표대회
• /
• pp.48.1-48.1
• /
• 2009

Performance of organic field-effect transistors (OFETs) with various temperature-cured polyacrylate(PA) copolymer as a gate insulator was studied. The PA thin film, which was cured at an optimized temperature, showed high dielectric strength (>7 MV/cm), low leakage current density ($5{\times}10^{-9}\;A/cm^2$ at 1 MV/cm) and enabled negligible hysteresis in MIS capacitor and OFET. A field-effect mobility of ${\sim}0.6\;cm^2/V\;s$, on/off current ratio (Ion/Ioff) of ${\sim}10^5$ and inverse subthreshold slope (SS) as low as 1.22 V/decwere achieved. The high dielectric strength made it possible to scale down the thickness of dielectric, and low-voltage operation of -5 V was successfully realized. The chemical changes were monitored by FT-IR. The morphology and microstructure of the pentacene layer grown on PA dielectrics were also investigated and correlated with OFET device performance.

• Applied Microscopy
• /
• 제46권2호
• /
• pp.76-82
• /
• 2016

Aloe vera has been used in the pharmaceutical, food and cosmetic industry for its therapeutic properties. However, there are not many current studies on the microstructure of A. vera compared to studies on the chemical constituents and health efficacy of A. vera. Therefore, we compared the morphology of an A. vera leaf using an optical microscope, a conventional scanning electron microscope (SEM) and a cryo-SEM. Especially, this study focused on observing the gel in the inner leaf of A. vera, which is challenging using standard imaging techniques. We found that cryo-SEM is most suitable method for the observation of highly hydrated biomaterials such as A. vera without removing moisture in samples. In addition, we found the optimal analytical conditions of cryo-SEM. The sublimation conditions of $-100^{\circ}C$ and 10 minutes possibly enable the surface of the inner leaf of A. vera to be observed in their "near life-like" state with retaining moisture. The experiment was repeated with A. arborescens and A. saponaria to confirm the feasibility of the conditions. The results of this study can be applied towards the basic research of aloe and further extend previous knowledge about the surface structures of the various succulent plants.

• Current Photovoltaic Research
• /
• 제9권4호
• /
• pp.137-144
• /
• 2021

In this study, the microstructure of the CVD-fabricated Cu(In,Ga)Se₂ (CIGSe) absorber layer by simulating the stacking sequence used in a co-evaporation method, and changes solar cell performance were investigated. The absorber layer prepared by stacking CuSe and (In,Ga)Se between InSe is separated into Ga-free CuInSe₂ and Ga-rich CIGSe, and transformed to CIGSe by selenization heat treatment with slight improvement in the the solar cell efficiency. However, in CVD, since the supply of liquid Cu-Se is not as active as in the co-evaporation method, the nanoocrystalline layer containing a large amount of Ga remained independently in the absorption layer, which acted as a cause of the loss of J_SC and FF. Therefore, by using a precursor structure in which CuGa is sputter-deposited on a single layer of InSe deposited by CVD, performance parameters of V_OC, J_SC, and FF could be greatly improved.

• 한국재료학회지
• /
• 제26권12호
• /
• pp.751-756
• /
• 2016

Graphite was diffusion-bonded by hot-pressing to W-25Re alloy using a Ti interlayer. For the joining, a uniaxial pressure of 25 MPa was applied at $1600^{\circ}C$ for 2 hrs in an argon atmosphere with a heating rate of $10^{\circ}C\;min^{-1}$. The interfacial microstructure and elemental distribution of the W-25Re/Ti/Graphite joints were analyzed by scanning electron microscopy (SEM). Hot-pressed joints appeared to form a stable interlayer without any micro-cracking, pores, or defects. To investigate the high-temperature stability of the W-25Re/Ti/Graphite joint, an oxy-acetylene torch test was conducted for 30 seconds with oxygen and acetylene at a 1.3:1 ratio. Cross-sectional analysis of the joint was performed to compare the thickness of the oxide layer and its chemical composition. The thickness of W-25Re changed from 250 to $20{\mu}m$. In the elemental analysis, a high fraction of rhenium was detected at the surface oxidation layer of W-25Re, while the W-25Re matrix was found to maintain the initial weight ratio. Tungsten was first reacted with oxygen at a torch temperature over $2500^{\circ}C$ to form a tungsten oxide layer on the surface of W-25Re. Then, the remaining rhenium was subsequently reacted with oxygen to form rhenium oxide. The interfacial microstructure of the Ti-containing interlayer was stable after the torch test at a temperature over $2500^{\circ}C$.

• 한국산학기술학회논문지
• /
• 제22권1호
• /
• pp.305-312
• /
• 2021

본 연구는 미세조직 분석을 통한 잠수함 탈출 트렁크 해치 스프링 파손부 개선에 관한 내용으로 잠수함 건조 중 발생한 탈출 트렁크 파손에 대한 발생원인 및 개선방안에 대해서 검토 하였다. 탈출 트렁크 스프링 파괴에 대한 원인 규명을 위해서 파손된 제품에서 시편을 채취하여 형광분석기를 이용한 재질의 화학성분을 비교 분석 하였고, 기계적 특성 변화를 검토하기 위해 파손부 주위로 비커스 경도를 측정 하였다. 특히, 스프링 파손부는 광학현미경 및 주사전자현미경을 이용하여 파면을 심층적으로 관찰하여 균열의 시작점 및 전파 경로를 확인하여 파괴에 대한 원인을 규명하고자 하였다. 최종적으로는 스프링 파손 원인 규명을 통한 스프링 형상 설계 방안을 제시하였고, 추가적으로 내부식성 및 내마모성이 우수한 나일론 도장을 도포하여 신규로 개선된 스프링을 제작 하였다. 실제 건조중인 잠수함 트렁크 해치에 부착하여 시험한 결과 기존 제품에 비해 해치 여닫음 시 스프링 간 접촉에 의한 도장 벗겨짐 현상이 감소하여 개선의 효과를 확인 하였다.

• 한국축산식품학회지
• /
• 제43권1호
• /
• pp.85-100
• /
• 2023

The present study aimed to evaluate the effects of high-intensity ultrasound (HIU) application on meat quality traits, sensory parameters, and the microstructure of semitendinosus muscle from Hanwoo cattle. The samples were treated in an ultrasonic bath (35 kHz) at an intensity of 800 W/cm² for 60 min, followed by aging at 1℃ for 0, 3, and 7 days. The application of ultrasound resulted in lower Warner-Bratzler shear force and higher myofibrillar fragmentation index values during the storage period. HIU also enhanced the tenderness, flavor, umami, and overall acceptability of cooked beef muscle. However, the electronic tongue evaluation results showed higher umami values in the control treatment on the seventh day of storage. The microstructure of sonicated meat showed disorganized myofibrillar architecture and swelling in the A-band region of sarcomeres during the storage period, which led to greater meat tenderness. The heatmap illustrated the high abundance of α-linolenic acid (C20:5n3) and eicosapentaenoic acid (C18:3n3) in sonicated meat samples on the third day of the storage. These results showed that HIU is a potential method for tenderizing and improving the sensory attributes of beef without compromising other quality aspects.

• The Korean Journal of Ceramics
• /
• 제5권4호
• /
• pp.324-330
• /
• 1999

$Si_3N_4$-$TiB_2$ with 2 wt% $Al_2O_3$ and 4 wt% $Y_2O_3$ additives was hot pressed in a flowing $N_2$ environment with varying $TiB_2$ content from 10 to 50 vol%. Variations of mechanical (hardness, fracture toughness, and flexual strength), and tribological properties as a function of $TiB_2$ content were investigated. As the content of $TiB_2$ increased, relative density decreased due to the chemical reaction of $TiB_2$in $N_2$ environment. The reduction of density causes mechanical properties to be degraded with an increase of $TiB_2$ in $Si_3N_4$. Tribological properties were dependent of microstructure as well as mechanical properties, however, they were degraded strongly by the chemical reaction of $Si_3N_4$-$TiB_2$ during hot pressing in $N_2$ environment. SEM and TEM observations, and X-ray diffraction analysis that the chemical reaction products at the interface are TiCN, Si, and $SiO_2$. Also, the comparison of XRD patterns of the $Si_3N_4$-40 vol% $TiB_2$ composites hot pressed at $1,750^{\circ}C$ for 1 hour between in $N_2$ and in Ar gas was made. The XRD peaks of Si and $SiO_2$ were not found in Ar, but still a weak peak of TiCN was presented.