• Bulletin of the Korean Chemical Society
• /
• v.35 no.7
• /
• pp.2049-2056
• /
• 2014

A simple method for exfoliating pristine graphite to yield mono-, bi-, and multi-layers of graphene sheets as a highly concentrated (5.25 mg/mL) and yielded solution in an organic solvent was developed. Pre-thermal treatment of pristine graphite at $900^{\circ}C$ in a sealed stainless steel bath under high pressures, followed by sonication in 1-methyl-2-pyrrolidinone solvent at elevated temperatures, produced a homogeneous, well-dispersed, and non-oxidized graphene solution with a low defect density. The electrical conductivities of the graphene sheets were very high, up to 848 S/cm. These graphene sheets were used to fabricate graphene-polyimide nanocomposites, which displayed a higher electrical conductivity (1.37 S/m) with an improved tensile strength (95 MPa). The synthesized graphene sheets and nanocomposites were characterized by transmission electron microscopy, scanning electron microscopy, atomic force microscopy, X-ray photoelectron spectroscopy, and Raman spectroscopy.

• Bulletin of the Korean Chemical Society
• /
• v.34 no.11
• /
• pp.3181-3182
• /
• 2013

• Bulletin of the Korean Chemical Society
• /
• v.19 no.10
• /
• pp.1113-1116
• /
• 1998

A new graphite intercalation compound (GIC), n-octylammonium tetrachlorofeffate(Ⅲ)-graphite, has been derived from well-known ferric chloride graphite intercalation compound. X-ray diffration study shows that the basal spacing of this new GIC is 20.8 Å. In order to investigate the local geometry around the iron atom in the graphite layers, X-ray absorption spectroscopy experiments were performed. The first discharge capacity of its exfoliated form is found to be 862 mAh/g, which is more than double the value of pristine graphite (384 mAh/g). Such a drastic increase implies that the exfoliated graphite is a promising electrode material.

• Macromolecular Research
• /
• v.14 no.3
• /
• pp.318-323
• /
• 2006

We investigated the rheological behaviors and orientation of three different types of layered silicate composite systems under external flow: microcomposite, intercalated and exfoliated nanocomposites. Rheological measurements under shear and uniaxial extensional flows, two-dimensional, small-angle X-ray scattering and transmission electron microscopy were conducted to investigate the properties, as well as nano- and micro-structural changes, of polymer/layered silicate nanocomposites. The preferred orientation of the silicate layers to the flow direction was observed under uniaxial extensional flow for both intercalated and exfoliated systems, while the strain hardening behavior was observed only in the exfoliated systems. The degree of compatibility between the polymer matrix and clay determined the microstructure of polymer/clay composites, strain hardening behavior and spatial orientation of the clays under extensional flow.

• Membrane Journal
• /
• v.15 no.4
• /
• pp.255-271
• /
• 2005

polymer/layered silicate nanocomposite (PLSNs) is new type of materials, based on clays usually rendered hydrophobic through ionic exchange of the sodium interlayer cation with an onium cation. It could be prepared via various synthetic routes comprising exfoliation adsorption, in situ intercalative polymerization and melt intercalation. The whole range of polymer is used, i.e. thermoplastics, thermosets and elastomers as a matrix. Two types of structure may be obtained, namely intercalated nanocomposites where the polymer chains are sandwiched in between silicate layers and exfolicate nanocomposites where the separated, individual silicate layers are more or less uniformly dispersed in the polymer matrix. This new family of materials exhibits enhanced properties at very low filer level, usually inferior to 5wt$\%$, such as increased mechanical properties, increase in thermal stability and gas barrier properties and good flame retardancy. Gas permeability through the PLSNs films decreased due to increased tortuosity made by intercalation or exfoliation of clay in polymer.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.27 no.6
• /
• pp.289-294
• /
• 2017

Films fabricated using atomic layer 2-dimensional nanosheets exhibit various physical properties depending on the size of the nanosheet. This is because the physical properties of the film depend on the interfacial properties between the sheets. Therefore, the synthesis of large-sized nanosheets is very important because it can reduce the dependency of the film on the interfacial properties. In this study, we succeeded in fabricating $TiO_x$ nanosheets with atomic layer thickness over micrometer size by using single-crystallized starting material and its chemical exfoliation. In addition, it was revealed that the mechanical agitation speed (the stirring speed of a magnetic bar) during the exfoliation step using the organic material is closely related to the nanosheet size and the colloidal concentration of the nanosheets.

• Journal of Conservation Science
• /
• v.29 no.1
• /
• pp.35-45
• /
• 2013

The Clay Statues of Donggwanwangmyo Shrine (Treasure No. 142) are highly damaged physical weathering which are crack, exfoliation. Pigment of surface are discolored by chemical weathering like dust. The result of ultrasonic velocity measurement, low velocity zone was measured the lowest part of Woojanggun Statue. Deficiency condition of pigment layer was evaluated quantitatively through infrared Thermography. As a result, exfoliation part was detected at high temperature. Making techniques of the Clay statues were identified by gamma rays, infrared TV, SEM. All Clay Statues were founded on wood base and joints of wood were fixed using thin iron wires. After wood base was twisted a straw rope, it was made by clay. Clay was blended with rice straw to prevention of crack and exfoliation. The upper side of clay layer was coated with Hanji(Korean handmade paper) and cotton in order to isolate the pigment layer.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.9-10
• /
• 2010

Since the discovery of graphene by mechanical exfoliation from graphite[1], various fabrication methods are available today such as chemical exfoliation, epitaxial graphene on SiC substrates, etc. In view of industrialization, the mechanical exfoliation method may not be an option. Epitaxial graphene on SiC substrates, in this respect, is by far more practical because the method consists of conventional thermal treatments familiar to semiconductor industry. Still, the use of the SiC substrate itself, and hence the incompatibility with the Si technology, lessens the importance of this technology in its future industrialization. In this context, we have tackled the problem of forming graphene on Si substrates (GOS). Our strategy is to form an ultrathin (~80 nm) SiC layer on top of a Si substrate, and to graphitize the top SiC layers by a vacuum annealing. We have actually succeeded in forming the GOS structure [2,3,4]. Raman-scattering microscopy indicates presence of few-layer graphene (FLG) formed on our annealed SiC/Si heterostructure, with the G ($1580\;cm^{-1}$) and the G'($2700\;cm^{-1}$) bands, both related to ideal graphene, clearly observed. Presence of the D ($1350\;cm^{-1}$) band indicates presence of defects in our GOS films, whose elimination remains as a challenge in the future. To obtain qualified graphene films on Si substrate, formation of qualified SiC films is crucial in the first place, and is achieved by tuning the growth parameters into a process window[5]. With a potential for forming graphene films on large-scale Si wafers, GOS is a powerful candidate as a key technology in bringing graphene into silicon technology.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.371.2-371.2
• /
• 2016

Graphene electronics is one of the promising technologies for the next generation electronic devices due to the outstanding properties such as conductivity, high carrier mobility, mechanical, and optical properties along with extended applications using 2 dimensional heterostructures. However, large contact resistance between metal and graphene is one of the major obstacles for commercial application of graphene electronics. In order to achieve low contact resistance, numerous researches have been conducted such as gentle plasma treatment, ultraviolet ozone (UVO) treatment, annealing treatment, and one-dimensional graphene edge contact. In this report, we suggest a fabrication method of one-dimensional graphene metal edge contact without using graphene exfoliation. Graphene is grown on Cu foil by low pressure chemical vapor deposition. Then, the graphene is transferred on $SiO_2/Si$ wafer. The patterning of graphene channel and metal electrode is done by photolithography. $O_2$ plasma is applied to etch out the exposed graphene and then Ti/Au is deposited. As a result, the one-dimensional edge contact geometry is built between metal and graphene. The contact resistance of the fabricated one-dimensional metal-graphene edge contact is compared with the contact resistance of vertically stacked conventional metal-graphene contact.

• Journal of the Korean institute of surface engineering
• /
• v.55 no.2
• /
• pp.84-90
• /
• 2022

With the growing interest in energy storage and conversion systems including secondary batteries, capacitors, and water electrolysis, various electrode materials are being developed to improve the energy efficiency. Among them, graphene is regarded as one of the promising candidates owing to its exceptional properties - large surface area, and excellent electrical conductivity. Herein, we report a facile one-step electrochemical approach to synthesize exfoliated graphene/Fe oxide compound. The effect of experimental conditions - the types of applied voltage, kinds of counter electrodes, acidity of electrolyte on the synthesis of graphene/Fe oxide compound is investigated.