• Advances in concrete construction
• /
• v.10 no.5
• /
• pp.403-416
• /
• 2020

This study investigated the effect of alkaline activators - NaOH_aq (NH) (NH: 0-16 M) and Na₂SiO_3aq (NS) (NS/NH: 0-3.5) in the synthesis of silico-manganese fume (SMF) and ground blast furnace slag (BFS) blended alkali-activated mortar (AASB). The use of individual activator was ineffective in producing AASB of sufficient fresh and hardened properties, compared to the synergy of both activators. This may be attributed to incomplete dissolution and condensation of oligomers required for gelation of the binder. An inverse relationship was noted among the fresh properties and the NH concentration or NS/NH ratio. This was influenced by the dissolution and condensation of silicate monomers under polymerization process. The maximum 28-day strength of ~45 MPa, setting time of 60 min and flow of 182 mm was obtained with the use of combined activators (10M-NH and NS/NH=2.5). The combined activators at NS/10M-NH=2.5 constituted SiO₂/Na₂O, H₂O/Na₂O and H₂O/SiO₂ molar ratio of 1.61, 17.33 and 10.77, respectively. This facilitated the formation of C-S-H, C/K-A-S-H and C-Mn-S-H in the framework together with an increase in the crystallinity due to more silicate re-organization within the aluminosilicate chain. On comparison of the high concentrated with mild alkali synthesized product, it revealed that the concentration of OH^- and Si monomers together with alkali metals influenced the dissolution of precursors and embedment of the constituent elements in the polymeric matrix. These factors eventually contributed to the microstructural densification of the mortar prepared with NS/10M-NH=2.5 thereby enhancing the compressive strength.

• Journal of Ginseng Research
• /
• v.33 no.3
• /
• pp.234-239
• /
• 2009

This study aims to establish the directions for the optimal nutrient contents determined by soil and leaf analyses. The study is to be used as a source for basic information in investigating the effects of nutritional environment on ginseng growth at the fields of Ansung region in Gyeonggi province. The physical property of soil porosity is closely related to ginseng growth, with more than 50% of good growth in the field. The optimal range of chemical properties in soil was analyzed as 0.20-0.28% T-N, 500-900 mg/kg Av.P$_2$O$_5$, and 2.3-3.5 cmol$^+$/kg Exch.Ca. The optimal range of inorganic nutrient contents in leaves was also analyzed. P value was less than 0.25%, and Mg was more than 0.22%. Other elements were not found clearly. The ratios of N/P, N/Mg, K/Mg, and Ca/P of leaves with good growth in the field showed 10<, 10-13, <14, 1<, respectively. In addition, the Ca:Mg:K ratio of the Exch.cation (cmol$^+$/kg) may be useful as an indicator in the assessment of plant growth in ginseng.

• The Journal of Engineering Geology
• /
• v.17 no.2 s.52
• /
• pp.187-196
• /
• 2007

The Dalseong acid mine drainage were studied focused on the characters of schwertmannite that controls geochemistry of the stream. Besides chemical analysis of stream water, particle size analysis, XRD SEM and TEM were performed on precipitates of streams and on wasted metalliferous ores. The AMD discharged from the abandoned mine reveals a decrease of pH and EC downward stream. Euhedral sulfur occurs as equigranular aggregates on the altered pyrite while fine acicula goethite coalesces to form cross, star, or starfish-like shapes. Water chemistry plotted on the Eh-pH diagram shows that schwertmannite and ferrihydrite are stable phases. Reddish brown precipitates consist of mostly schwertmannite with less goethite, whereas yellowish brown precipitates are composed of geothite with less schwertmannite. The particle size of precipitates ranges $d(0.1)\;0.861{\mu}m{\sim}3.769{\mu}m,\;d(0.5)\;3.984{\mu}m{\sim}15.255{\mu}m,\;and\;d(0.9)\;9.875{\mu}m{\sim}56.726{\mu}m$. Schwertmannite is characterized by equigranular spheric form. Pincushion or spicule with 100nm width and $200{\sim}300nm$length form on schwertmannite sphere with radial growth patterns. It is highly probable that reddish or yellowish brown precipitates formed in many AMDs may contain schwerhnannite. Because it can serve as sink for removing heavy elements by adsorption in AMD system, there is a need to correctly identify schwertmannite in precipitates and to characterize its phase stability.

• Journal of Environmental Impact Assessment
• /
• v.29 no.4
• /
• pp.252-271
• /
• 2020

In this study, we investigated physical and chemical properties such as grain size, heavy metal pollution, magnetic properties, and their environmental impacts of road dusts (RD) collected from 14 sampling points in Daebul industrial Complex. Heavy metal concentrations in RD were in the order of Fe>Zn>Cu>Pb>Cr>Ni>As>Cd>Hg, and this pollution pattern was related to major industries and traffic activities in this area. The results of the correlation analysis between heavy metal elements and particle size in RD showed that Fe and all of analyzed heavy metals had a significant correlation with each other and metal concentrations had a significantly negative correlation (p<0.05). However, due to the input of large metal particles some heavy metal concentrations in the particle fraction of >1000 ㎛ were highest. Pollution load per unit area of this fraction was the highest among the grain size fractions. Cr, Ni, Cu, Zn, Cd, Pb levels in RD decreased and the levels of Cr, Ni, Cu, Zn, Cd, and Pb were reduced to 85 (As) -22 (Ni)% of the whole after removal of MFs fraction from RD. The mean heavy metal levels in the study area did not exceed the soil contamination guide value of Korea, indicating that heavy metal levels in RD were not a concern. However, at some sampling points, Zn concentrations were exceeded the soil contamination guide value for the 3rd areas of Korea and this result indicated that further studies of the impact of RD on the surrounding environment through re-suspension or non-point pollution, and of effective management methods are required.

• Proceedings of the KWS Conference
• /
• 2010.05a
• /
• pp.51-51
• /
• 2010

Recently just as in the automobile industry, shipbuilders also try to reduce material consumption and weight in order to keep operating costs as low as possible and improve the speed of production. Naturally industry is ever searching for welding techniques offering higher power, higher productivity and a better quality. Therefore it is important to have a details research based on the various welding process applied to steel and other materials, and to have the ability both to counsel interested companies and to evaluate the feasibility of implementation of this process. Submerged-arc welding (SAW) process is usually used about 20% of shipbuilding. Similar to gas metal arc welding(GMAW), SAW involves formation of an arc between a continuously-fed bare wire electrode and the work-piece. The process uses a flux to generate protective gases and slag, and to add alloying elements to the weld pool and a shielding gas is not required. Prior to welding, a thin layer of flux powder is placed on the work-piece surface. The arc moves along the joint line and as it does so, excess flux is recycled via a hopper. Remaining fused slag layers can be easily removed after welding. As the arc is completely covered by the flux layer, heat loss is extremely low. This produces a thermal efficiency as high as 60% (compared with 25% for manual metal arc). SAW process offers many advantages compared to conventional CO2 welding process. The main advantages of SAW are higher welding speed, facility of workers, less deformation and better than bead shape & strength of welded joint because there is no visible arc light, welding is spatter-free, fully-mechanized or automatic process, high travel speed, and depth of penetration and chemical composition of the deposited weld metal. However it is difficult to application of thin plate according to high heat input. So this paper has been focused on application of the field according to SAW process for thin plate in ship-structures. For this purpose, It has been decided to optimized welding condition by experiments, relationship between welding parameters and bead shapes, mechanical test such as tensile and bending. Also finite element(FE) based numerical comparison of thermal history and welding residual stress in A-grade 3.2 thickness steel of SAW been made in this study. From the result of this study, It makes substantial saving of time and manufacturing cost and raises the quality of product.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.16 no.3
• /
• pp.95-100
• /
• 2006

Synthesis of the non-swelling property micas was carried out by hydrothermal method. In order to artificially induce the diffusion of ions, a rotating system was attached to the hydrothermal apparatus and by adding 0.7 mm zircon beads, synthesis of the non-swelling property micas could be performed in a low temperature area. The hydrothermal conditions for the preparation of micas were a reaction temperature of $260^{\circ}C$, for 72 hrs, using $1K_2O,\;1Al(OH)_3,\;4Mg(OH)_2\;and\;6SiO_2$ as the starting materials and a 8M-KOH solution as the hydrothermal solvent. The micas obtained under these conditions were a plate shape with a size of $2.89{\mu}m$ and showed a whiteness of over 97 %. Also, through the FT-IR analysis, because the absorption peak of the $Mg_3OH$ vibration was observed at approximately $3700cm^{-1}$, it could be known that it was phlogopite of non-swelling property showing the chemical composition of $KMg_3AlSi_3O_{10}(OH)_2$. This result was very consistent with the EDS analysis where O (41.34 %), Mg (3.88 %), Al (11.45 %), Si (17.62 %) and K (25.71%) elements were detected.

• Journal of Technologic Dentistry
• /
• v.32 no.3
• /
• pp.195-207
• /
• 2010

Purpose: The purpose of this study was to observe the microstructural changes of surface in the specimens, performing the shear bond strength testing. The currently most used non-precious alloys are nickel-chromium based alloys with or without beryllium. However, their biocompatibility has been questioned concerning possible damages to the health of the patient and professionals involved in the fabrication of prosthesis caused by long exposure to Ni and Be. An option to nickel-chromium alloys is the cobalt-chromium alloy, an alternative that does not sacrifice the physical properties of the metal porcelain systems. Studies in the animals substantially show that the cobalt-chromium alloys are relatively well tolerated, being therefore more biocompatible than the nickel-chromium alloys. Methods: Non-addition Be to nickel-chromium based alloy(Bellabond plus) and cobalt-chromium alloy which has been widely used(Wirobond C) fused with ZEO light porcelain classified control group and cobalt-chromium alloy which is developing alloy of Alphadent company in Korea(Alphadent alloy) fused with ZEO light porcelain classified experimental group. The specimens of $4mm{\times}4mm{\times}0.5mm$ were prepared as-cast and as-opaque to cast body to analyze the mechanical characteristic change, the microstructure of alloy surface. The phase change was used to observe through XRD analysis and OM/SEM was used to observe the surface of specimens as-cast and as-opaque to cast body. Chemical formation of their elements was measured with EDS. Then hardness was measured with Micro Vicker's hardness tester. Shear bond strength test thirty specimens of $10mm{\times}10mm{\times}2mm$ was prepared, veneered, 3mm high and 3mm in diameter, over the alloy specimens. The shear bond strength test was performed in a universal testing machine(UTM) with a cross head speed of 0.5mm/min. Ultimate shear bond strength data were analyzed with one-way ANOVA and the Scheffe's test (P<0.05). Within the limits of this study, the following conclusions were drawn: The X-ray diffraction analysis results for the as-cast and as-opaque specimens showed that the major relative intensity of Bellabond plus alloy were changed smaller than Wirobond C and Alphadent Co-Cr based alloys. Results: Microstructural analysis results for the opaque specimens showed all the alloys increased carbides and precipitation(PPT). Alphadent Co-Cr based alloy showed the carbides of lamellar type. The Vickers hardness results for the opaque specimens showed Wirobond C and Alphadent Co-Cr based alloys were increaser than before ascast, but Bellabond plus alloy relatively decreased. The mean shear bond strengths (MPa) were: 33.11 for Wirobond C/ZEO light; 25.00 for Alphadent Co-Cr alloy/ZEO light; 18.02 for Bellabond plus/ZEO light. Conclusion: The mean shear bond strengths for Co-Cr and Ni-Cr based alloy were significantly different. But the all groups showed metal-metal oxide modes in shear bond strengths test at the interface.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.12 no.2
• /
• pp.41-51
• /
• 2004

Recycled plastic containers, so-called 'Tarai' in Korea which are often used as food containers, were collected from 23 domestic manufacturers. Then, their components were analyzed to find out whether they are safe for the use of food-contact material, to meet the standards and specifications of Korean hygienic regulations, the 'Food Code.' The components of the material were analyzed by using Fourier Transform-Infrared (FT-IR), Differential Scanning Calorimeter (DSC), and Elementary Analyzer (EA). The analysis of the FT-IR and the DSC showed that the main component of the samples was polyethylene. Furthermore, the analysis of the EA for 'Tarai' sample revealed the same ratio of C and H elements as in the case of polyethylene which was 1 to 2. Phenol and formaldehyde were not detected in all the samples. As for the antioxidant tests, Irganox 1010, Irganox 1076 and Irganox 1330 were detected in various samples. With regard to the material test for heavy metals, 7 out of 23 samples exceeded the limit value of 100 mg/kg in lead contents. No standard and specification is yet prescribed in the 'Food Code' for the material of 'Tarai' as plastic containers for food. This study suggests that the use of 'Tarai' as a food container should be strictly controlled.

• Journal of the Mineralogical Society of Korea
• /
• v.22 no.2
• /
• pp.97-106
• /
• 2009

It is known that the natural amethyst is changed to citrine after heat treatment. However, when all amethyst samples from Zambia were heat-treated in the temperature range of $350{\sim}380^{\circ}C$ for 1 hour, the result was that five out of eight samples were changed to citrine and all the rest of samples became rock crystal quartz. These differences in the color appearance seem to be influenced by the original colors contained in the amethyst before the heat treatment. The amethyst containing yellow color changed to citrine and the amethyst without containing yellow color changed to rock crystal quartz after the heat treatment. The results compared after the instrumental analysis on the difference of color change, it showed the differences of peak intensity in 3,400 $cm^{-1}$ and the existence and non-existence of peak at the range of 5,200${\sim}$5,400 $cm^{-1}$ in FTIR. It revealed the difference in the quantity of Cr which is a trace element in the WD-XRF analysis. The identical result in the FTIR spectra before and after the heat treatment reveals that the heat treatment did not cause any change in the main composing elements or crystal structure.

• Journal of Conservation Science
• /
• v.33 no.3
• /
• pp.155-165
• /
• 2017

As interest in the public display of art and outdoor sculptures is increasing, the conservation and treatment of these sculptures is becoming increasingly crucial. Long-term exposure to the natural elements and atmospheric pollution can cause corrosion and deterioration in outdoor sculptures. In the case of Kim Chan Shik's "Feeling", which was exhibited in the outdoor sculpture park at the National Museum of Modern and Contemporary Art (MMCA), the patina of the sculpture was damaged during a long outdoor exhibition. Therefore, the treatment process was as follows: recording of condition, sanding, repatination, and wax coating. Consequently, the sculpture was restored similar to the original. Chemical analysis revealed that the sculpture was crafted from bronze and was cast from a quaternary alloy of Cu-Pb-Sn-Zn. The welding is lower in Zn, Sn, and Pb content than the metal used in the sculpture itself. Bright strains contain about 13.0 wt% Sn and 10.5 wt% Pb. The strains are higher in Sn and Pb content than the rest of the metal in the sculpture (7.0 wt% Sn and 4.4 wt% Pb). As a result of component analysis and microstructure observation, the material is estimated to have been made by casting without artificial treatment.