• Korean Journal of Materials Research
• /
• v.8 no.6
• /
• pp.532-537
• /
• 1998

The purpose of this study was to investigate the behavior of ozone in DI water and the reaction with wafers during the semiconductor wet cleaning process. The solubility of ozone in DI water was not only dependent on the temperature but also directly proportional to the input concentration of ozone. The lower the initial ozone concentration and the temperature, the longer the half-life time of ozone. The reaction order of ozone in DI water was calculated to be around 1.5. The redox potential reached a saturation value in 5min and slightly increased as the input ozone concentrations increased. The completely hydrophilic surface was created in Imin when HF etched silicon wafer was cleaned in ozonized DI water containing higher ozone concentrations than 2ppm. Spectroscopic ellipsometry measurements showed that the chemical oxide formed by ozonized DI water was measured to be thicker than that by piranha solution. The wafers contaminated with a non-ionic surfactant were more effectively cleaned in ozonized DI water than in piranha and ozonized piranha solutions.

• Journal of Periodontal and Implant Science
• /
• v.31 no.2
• /
• pp.451-463
• /
• 2001

Following the extensive use of implant, the incidence of peri-implantitis increases. Guided bone regeneration has been used for the optimal treatment of this disease. Because implant surface was contaminated with plaque and calculus, cleaning and detoxification were needed for the reosseointegration when guided bone regeneration was performed. Various mechanical and chemical methods have been used for cleaning and detoxification of implant surface, air-powder abrasive and oversaturated citrate were known to be most effective among these methods. However, these methods were incomplete because these could not thoroughly remove bacteria of implant surface, moreover deformed implant surface. Recent studies for detoxification of the implant surface using laser were going on, $CO_2$ laser and Soft Diode laser were known to be effective among these methods. The purpose of this study was to obtain clinical guide by application these laser to implant surface. 15 experimental machined pure titanium cylinder models were fabricated. The $CO_2$ laser treatment under dry, wet and hydrogen peroxide condition or the Soft Diode laser treatment under Toluidine blue O solution condition was performed on the each of models. Each groups were examined with SPM and SEM to know whether their surface was changed. The results were as follows : 1. Surface roughness and surface form weren't changed when $CO_2$ laser was usedunder dry condition(P>0.05). 2. Surface roughness and surface form weren't changed when $CO_2$ laser was used under wet condition(P>0.05). 3. Surface roughness and surface form weren't changed when $CO_2$ laser was used under hydrogen peroxide condition(P>0.05). 4. Surface roughness and surface form weren't changed when Soft Diode laser was used under toluidine blue O solution condition(P>0.05). From the result of this study, it may be concluded that the $CO_2$ laser having relatively safe pulse mode and the Soft Diode laser used with photosensitizer can be used safely to treat peri-implantitis.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.11 no.6
• /
• pp.1099-1103
• /
• 2007

TFT's have been intensively researched for possible electronic and display applications. Through tremendous engineering and scientific efforts, a-Si:H TFT fabrication process was greatly improved. In this paper, the reason on defects occurring at a-Si:H TFT fabrication process is analyzed and solved, so a-Si:H TFT's yield is increased and reliability is improved. The a-Si:H TFT of this paper is inverted staggered type TFT. The gate electrode is formed by patterning with length of $8{\mu}m{\sim}16{\mu}m$ and width of $80{\sim}200{\mu}m$ after depositing with gate electrode (Cr). We have fabricated a-SiN:H, conductor, etch-stopper and photo-resistor on gate electrode in sequence, respectively. We have deposited n+a-Si:H, NPR(Negative Photo Resister) layer after forming pattern of Cr gate electrode by etch-slower pattern. The NPR layer by inverting pattern of upper Sate electrode is patterned and the n+a-Si:H layer is etched by the NPR pattern. The NPR layer is removed. After Cr layer is deposited and patterned, the source-drain electrode is formed. The a-Si:H TFT made like this has problems at photo-lithography process caused by remains of PR. When sample is cleaned, this remains of PR makes thin chemical film on surface and damages device. Therefor, in order to improve this problem we added ashing process and cleaning process was enforced strictly. We can estimate that this method stabilizes fabrication process and makes to increase a-Si:H TFT's yield.

• Journal of the Korean Applied Science and Technology
• /
• v.38 no.1
• /
• pp.19-28
• /
• 2021

Corrosion is the degradation of metals by reaction with the environment. It is difficult to completely remove. Corrosion proceeds rapidly after the protective barrier is destroyed, and several reactions occur that alter the composition and properties of the metal surface and local environments, such as diffusion of metal cations into the matrix, the formation of oxides, and local pH changes. The study of corrosion of steel and iron is of theoretical and practical interest and is receiving considerable attention. Acid solutions, which are widely used in industrial pickling, acid descaling, cleaning and acidification of oil wells, require the use of corrosion inhibitors to suppress corrosion attacks on metallic materials. Physical removal of rust requires expensive special equipment, and chemical removal of it can cause corrosion or shorten the life of the metal. In this study, an eco-friendly rust cleaner was developed using cosmetics and food materials by applying the concept of perm reducing agent and chelate, and applied to remove rust from industrial and hot water pipes and various industrial devices. As a result, it was found that rust cleaners remove rust more effectively and safely compared to conventional treatment methods. At the same time, the rust removal efficiency was 1.75 to 2.5 times better for industrial piping and 1.56 to 2.2 times better for boiler hot water than conventional methods.

• Applied Chemistry for Engineering
• /
• v.16 no.5
• /
• pp.677-683
• /
• 2005

In this work, the effect of additives such as solvent, sodium dodecyl sulfate and NaCl on microemulsion phase behavior and flux removal efficiency in systems containing commercial alkyl ethoxylates nonionic surfactant was investigated. The addition of a n-hydrocarbon as a solvent produced on O/W (Oil/Water) microemulsion phase over a wider range of temperature and cosurfactant to surfactant ratios. Especially, the addition of n-hexadecane to the surfactant system, which was the most hydrophobic solvent among the solvents used in this study, produced a microemulsion phase over a wide range of temperatures and promoted formation of a microemulsion phase at lower temperatures. The candidate for cleaner samples, prepared from phase behavior experiments, showed excellent removal efficiency for abietic acid at $40^{\circ}C$. These data suggested the potential applicability of hydrocarbons to actual cleaner formulations.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.30 no.4 s.48
• /
• pp.525-532
• /
• 2004

N-acyl taurates are known as environmental-friendly and non-irritating to skin. In this study, the physicochemical properties of N-acyl taurates, which are amide-type anionic surfactants, were measured and also compared with sulfate-type anionic surfactants that show low biodegradability and are highly irritating to skin. The possibility of replacing the currently existing sulfate-type surfactants by N-acyl taurates was examined. Based on the experimental results, shampoos were formulated with these anionic surfactants and their stability and properties were measured. The possibility of application of amide-type surfactants to personal care cleaner was evaluated. Experimental results show that N-acyl taurates have various favorable aspects in making personal care cleanser: high viscosity, low surface tension, and low CMC values. These properties of N-acyl taurates generate nano-scale particles in emulsion, which is stable due to its high viscosity. This emulsion also has good cleaning ability with small amount of usage due to easy penetration into contaminants. Shampoo with N-methyl oleyl taurate showed high yield point and constant viscosity, and formed stable emulsion with nano- scale uniform particles. These results suggest that N-acyl taurates play an important role in making stable Interior structure in shampoo, and which improves the storage property.

• Applied Chemistry for Engineering
• /
• v.20 no.1
• /
• pp.9-14
• /
• 2009

A zwitterionic surfactant shows not only detergency but also softening effect since it shows characteristics of a nonionic or an anionic surfactant above an isoelectric point, while showing characteristics of a cationic surfactant below an isoelectric point. Therefore, a zwitterionic surfactant can serve as a dual function surfactant by a single molecule through the interconversion of cleaning and softening effects depending on pH of the aqueous solution. In this study, the dual function characteristics of an amine oxide zwitterionic surfactant were investigated by measuring the zeta potential and the isoelectric point using quartz crystal microbalance (QCM). In addition, the physical properties of an amine oxide surfactant such as critical micelle concentration, surface tension, interfacial tension, contact angle and viscosity were measured and phase behavior study was also performed. The isoelectric point of an amine oxide surfactant determined by zeta potential measurement was near 7.35 and that obtained by QCM experiment was about 7.4, where both results were found to be close to the value reported in the literature.

• Proceedings of the Membrane Society of Korea Conference
• /
• 1998.06a
• /
• pp.135-153
• /
• 1998

Nanofiltration (NF) is a recently introduced term in membrane separation. In 1988, Eriksson was one of the first authors using the word 'nanofiltration' explicitly. Some years before, FilmTech started to use this term for their NF50 membrane which was supposed to be a very loose reverse osmosis membrane or a very tight ultrafiltration membrane. Since then, this term has been introduced to indicate a specific boundary of membrane technology in between ultrafiltration and reverse osmosis. The application fields of the NF membranes are very broad as follows: Demeneralizing water, Cleaning up contaminated groundwater, Ultrapure water production, Treatment of effleunts containing heavy metals, Offshore oil platforms, Yeast production, Pulp and paper mills, Textile production, Electroless copper plating, Cheese whey production, Cyclodextrin production, Lactose production. The earliest NF membrane was made by Cadotte et al, using piperazine and trimesoyl chloride as monomers for the formation of polyamide active layer of the composite type membrane. They coated very thin interfacially potymerized polyamide on the surface of the microporous polysulfone supports. The NF membrane exhibited low rejections for monovalent anions (chloride) and high rejections for bivalent anions (sulphate). This membrane was called NS300. Some of the earliest NF membranes, like the NF40 membrane of FilmTech, the NTR7250 of Nitto-Denko and the UTC20 and UTC60 of Toray, are formed by a comparable synthesis route as the NS300 membrane. Commercially available NF membranes nowadays are as follows: ASP35 (Advanced Membrane Technology), MPF21; MPF32 (Kiryat Weizmann), UTC20; UTC60; UTC70; UTC90 (Toray), CTA-LP; TFCS (Fluid Systems), NF45; NF70 (FilmTec), BQ01; MX07; HG01; HG19; SX01; SX10 (Osmonics), 8040-LSY-PVDI (Hydranautics), NF CA30; NF PES 10 (Hoechst), WFN0505 (Stork Friesland). The typical ones among the commercially available NF membranes are polyamide composite membrane consisting of interfacially polymerized polyamide active layer and microporous support. While showing high water fluxes and high rejections of multivalent ions and small organic molecules, these membranes have relatively low chemical stability. These membranes have low chlorine tolerance and are unstable in acid or base solution. This chemical instability is appearing to be a big obstacle for their applications. To improve the chemical stability, we have tried, in this study, to prepare chemically stable NF membranes from PVA. The ionomers and interfacially polymerized polyamide were used for the modification of'the PVA membranes. For the detail study of the active layer, homogeneous NF membranes made only from active layer materials were prepared and for the high performance, composite type NF membranes were prepared by coating the active layer materials on microporous polysulfone supports.

• Korean Chemical Engineering Research
• /
• v.51 no.6
• /
• pp.666-670
• /
• 2013

Recovery method of silicon wafer from defective products generated from manufacturing process of silicon solar cells was studied. The removal effect of the N layer and antireflection coating (ARC) of the waste solar cell were investigated at room temperature ($25^{\circ}C$) by variation of concentration of $H_3PO_4$, $NH_4HF_2$, and concentration and types of chelating agent. Removal efficiency was the best in the conditions; 10 wt% $H_3PO_4$ 2.0 wt% $NH_4HF_2$, 1.5 wt% Hydantoin. Increasing the concentration of $H_3PO_4$, the surface contamination degree was increased and the thickness of the silicon wafe became thicker than the thickness before surface treatment because of re-adsorption on the silicon wafer surface by electrostatic attraction of the fine particles changed to (+). The etching method by mixed solution of $H_3PO_4$-$NH_4HF_2$-chelating agents was expected to be great as an alternative to conventional RCA cleaning methods and as the recycle method of waste solar cells, because all processes are performed at room temperature, the process is simple, and less wastewater, the removal efficiency of the surface of the solar cell was excellent.

• Journal of Environmental Science International
• /
• v.24 no.5
• /
• pp.633-639
• /
• 2015

The experience of natural dyeing is expected to be effective in promoting health through good exercise, in giving emotional stability based on the functional aromatic components of the dyeing material, and in improving self-esteem and increasing positive experiences through the behavior of creation. A natural dyeing material easily found around us, artemisia has long been used in food and Oriental medicine and was recently found to contain antioxidative, anticancer, deodorizing, antibacterial, anti-obesity, and anti-diabetes substances through chemical analysis. It has also been reported that group reminiscence therapy using the fragrance of artemisia is effective in relieving pain and depression and in promoting ego integrity in the elderly population. This study aimed to make a comparative analysis of dyeability, washing fastness, and deodorization between Artemisia princeps, Artemisia iwayomogi, and Artemisia annua, all of which are considered to be healthful and functional dyeing materials, among about thirty domestic plants in the genus of Artemisia and to provide basic data concerning natural dyeing in mind-peace education for the silver generation. The fabric dyed and post-mordanted at $80^{\circ}C$ for 40 minutes showed the greatest surface color variation; in this condition, artemisia princes (32.29) gave the greatest color difference, followed by artemisia iwayomogi (31.07) and artemisia annua (26.17). While all the types of artemisia were excellent in washing fastness, dry-cleaning fastness, and rubbing fastness at the fourth- or fifth-grade, light fastness was at the third grade for artemisia princes, at the second to third grade for artemisia annua, and at the second grade for artemisia iwayomogi; therefore, artemisia princes was found to give better fastness than the other two types of artemisia. In determining functionality of the fabric dyed with artemisia, deodorization test also found that the fabric dyed with artemisia princes had 20% higher deodorization.