• 한국농촌건축학회논문집
• /
• 제21권4호
• /
• pp.45-52
• /
• 2019

Chemical grouting method is mainly used for construction of dams and reservoirs, stabilization and reinforcement of slopes, reinforcement of soft grounds such as embankments, dredging and landfills, the order of earthquake response method, and the reinforcement of structures. Recently, it is widely applied in construction sites such as highways, airfields, high-speed railways, subsea facilities, port construction works, tunnels, and subway works. As such, the demand for grouting continues to increase. The development of the grouting method was focused on increasing the strength of the ground, and the development of the chemical additives, the injection device, and the stirring device were mainly performed. But ordinary portland cement used for grouting is a product that consumes natural resources such as limestone, generates a large amount of greenhouse gases, consumes a large amount of energy sources, and it is time to develop products and new methods to replace them. In this study, Ordinary Portland Cement and New Grouting Binder (circulating fluidized bed boiler fly and blast furnace slag) were compared and analyzed by the following test. Homo-gel strength and homo-gel time, water quality analysis of the water used and soil contamination process tests of homo-gel samples were performed. In the case of NGB, when Using water is used as the reservoir water, the strength measured smaller than that of the other water. However, it shows about 2.5 times greater than the homo-gel compressive strength applied to OPC (7-day, reservoir water), so there is no problem with water quality when applied.

• Carbon letters
• /
• 제25권
• /
• pp.14-24
• /
• 2018

Electrochemical properties and performance of composites performed by incorporating metal oxide or metal hydroxide on carbon materials based on graphene and carbon nanotube (CNT) were analyzed. From the surface analysis by field emission scanning electron microscopy and field emission transmission electron microscopy, it was confirmed that graphene, CNT and metal materials are well dispersed in the ternary composites. In addition, structural and elemental analyses of the composite were conducted. The electrochemical characteristics of the ternary composites were analyzed by cyclic voltammetry, galvanostatic charge-discharge tests, and electrochemical impedance spectroscopy in 6 M KOH, or $1M\;Na_2SO_4$ electrolyte solution. The highest specific capacitance was $1622F\;g^{-1}$ obtained for NiCo-containing graphene with NiCo ratio of 2 to 1 (GNiCo 2:1) and the GNS/single-walled carbon $nanotubes/Ni(OH)_2$ (20 wt%) composite had the maximum specific capacitance of $1149F\;g^{-1}$. The specific capacitance and rate-capability of the $CNT/MnO_2/reduced$ graphene oxide (RGO) composites were improved as compared to the $MnO_2/RGO$ composites without CNTs. The $MnO_2/RGO$ composite containing 20 wt% CNT with reference to RGO exhibited the best specific capacitance of $208.9F\;g^{-1}$ at a current density of $0.5A\;g^{-1}$ and 77.2% capacitance retention at a current density of $10A\;g^{-1}$.

• Journal of Ginseng Research
• /
• 제35권4호
• /
• pp.487-496
• /
• 2011

Good manufacturing practice (GMP)-based quality control is an integral component of the common technical document, a formal documentation process for applying a marketing authorization holder to those countries where ginseng is classified as a medicine. In addition, authentication of the physico-chemical properties of ginsenoside reference materials, and qualitative and quantitative batch analytical data based on validated analytical procedures are prerequisites for certifying GMP. Therefore, the aim of this study was to propose an authentication process for isolated ginsenosides $Rb_1$ and $Rg_1$ as reference materials (RM) and for these compounds to be designated as RMs for ginseng preparations throughout the world. Ginsenoside $Rb_1$ and $Rg_1$ were isolated by Diaion HP-20 adsorption chromatography, silica gel flash chromatography, recrystallization, and preparative HPLC. HPLC fractions corresponding to those two ginsenosides were recrystallized in appropriate solvents for the analysis of physico-chemical properties. Documentation of the isolated ginsenosides was made according to the method proposed by Gaedcke and Steinhoff. The ginsenosides were subjected to analyses of their general characteristics, identification, purity, content quantitation, and mass balance tests. The isolated ginsenosides were proven to be a single compound when analyzed by three different HPLC systems. Also, the water content was found to be 0.940% for $Rb_1$ and 0.485% for $Rg_1$, meaning that the net mass balance for ginsenoside $Rb_1$ and $Rg_1$ were 99.060% and 99.515%, respectively. From these results, we could assess and propose a full spectrum of physicochemical properties for the ginsenosides $Rb_1$ and $Rg_1$ as standard reference materials for GMP-based quality control.

• Elastomers and Composites
• /
• 제45권4호
• /
• pp.298-308
• /
• 2010

패럴린 박막의 기계적 성질과 표면 특성을 개선하기 위해 Xylydene계 다이머(DPX-C, DPX-D, DPX-N)를 사용하여 각각의 다이머에 대한 증착 조건과 투입량에 따른 박막의 두께를 조절함으로써 단일 패럴린-C, D, N 박막과 두 가지 타입이 혼합된 하이브리드 타입의 화학적, 물리적 패럴린 박막을 제조하였다. 패럴린 증착은 화학기상증착법(chemical vapor deposition: CVD)을 이용하였으며, 열분석을 통해 단일 박막과 하이브리드 타입의 박막에 대한 열적 특성을 비교 분석하였다. 인장 강도와 신장율 그리고 인열력 시험을 통해 박막에 대한 기계적 물성을 알아보았으며, 접촉각과 표면 에너지를 측정하여 박막에 대한 표면 특성을 관찰하였다. 두 가지 타입이 혼합된 하이브리드 타입의 화학적 패럴린 박막은 서로 다른 다이머의 장단점을 상호 보완시켜 줄 수 있으며, 물리적 패럴린 박막은 기재에 코팅되는 면과 반대 면의 박막 특성을 자유롭게 조절할 수 있다.

• 공업화학
• /
• 제29권6호
• /
• pp.677-681
• /
• 2018

본 연구에서는 탄소블럭의 고밀도화를 위하여 불소화 표면처리된 코크스와 바인더피치를 압축성형으로 탄소블럭을 제조하였다. 불소화 표면처리 후 코크스 표면에 불소원소는 XPS 분석을 통하여 최대 24.14 at%가 도입된 것을 확인하였다. 불소화된 코크스와 바인더피치의 젖음성을 반응온도에 따라 평가하였다. 접촉각 측정 결과로부터 불소원소가 코크스 표면에 도입될수록 바인더피치와의 젖음성이 약 64.7% 향상됨을 알 수 있었다. 또한, 불소가 가장 많이 도입된 탄소블럭의 밀도는 미처리된 코크스로부터 제조된 탄소블럭의 밀도 대비 최대 6.8% 증가하였다.

• 공업화학
• /
• 제32권3호
• /
• pp.260-267
• /
• 2021

본 연구에서는 코코넛 오일로부터 카르복실레이트계 음이온 계면활성제 SLEC-3을 합성하였으며, 합성된 계면활성제의 구조를 FT-IR, ¹H-NMR 및 ¹³C-NMR 분석을 통하여 확인하였다. 합성한 계면활성제 SLEC-3에 대하여 임계 마이셀 농도, 정적 및 동적 표면장력, 유화력, 거품 안정성 등의 계면 물성을 측정한 결과, 기존 세제 제품에서 널리 사용되는 음이온 계면활성제 SLES와 비교하여 계면 활성이 보다 우수하고 계면 에너지를 낮추는데 더 효과적이었다. 또한 SLCE-3에 대한 생분해성, 급성 경구 독성 및 급성 피부자극 시험을 실시한 결과, 저자극 및 저독성을 가지고 있기 때문에 세제 및 세정제 제품에 적용할 수 있을 것으로 판단되었다.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2002년도 학술.기술논문발표회
• /
• pp.67-76
• /
• 2002

Self-leveling material(SLM) is one of the floor finishing materials which make flat surface like as water level by itself in a short time. So it is possible to increase construction speed and enhance economical efficiency. In this study, author intended to develop SLM for the industrial warehouse and factory loading heavy weight machinery and vehicles. The demanded properties for this type of SLM are above 20mm of flow value and above 300kgf/cm2 of 28-days compressive strength. To possess demended strength and fluidity, SLM have to be composed of many types of binders and chemical additives. So it is difficult to decide suitable mixing proportion of composition materials. In this study, author investigated the weight percentage effect of main composition materials for high-strength self-leveling material, by experimental design such as tables of orthogonal arrays and simplex design, and by statistical analysis such as analysis of variance and analysis of response surface. Variables of experiments were ordinary portland cement(OPC), alumina cement(AC), anhydrous gypsum(AG), lime stone(LS) and sand, and properties of tests were fluidity of fresh state and strength of hardened state. Results of this study are showed that suitable mix proportions of binders for the high strength self-leveling materials are two groups. One is 78~85.5% OPC, 7.5~9.5% AC, 9~12.5% AG and the other is 72.5~78% OPC, 9~12.5% AC, 13~l5% AG.

• 대한기계학회논문집A
• /
• 제32권11호
• /
• pp.937-942
• /
• 2008

This research investigated to find out the possibilities of applying FRPs to the AUVs. In this study, two kinds of metal materials, which is one of the popularly used materials for manufacturing AUVs, and 6 kinds of FRP materials were considered. Material properties of FRPs were derived by tensile tests and chemical analysis. Moreover, various types of AUVs were designed by 8 kinds of materials. From structural analysis, we can find out that the weights of AUV by CFRP-Autoclave could be reduced by 60% in comparison with the weights of AUV by Al 7075-T6. Also, 40% weight reduction could be expected compared to the AUV by Ti-6Al-4V. In this result, we could conclude that the material of CFRP-Autoclave have various merits and potentialities as one of the AUV materials.

• 분석과학
• /
• 제25권2호
• /
• pp.102-113
• /
• 2012

현행 환경오염공정시험기준 중 먹는 물 수질공정시험기준과 실내공기질 공정시험기준에 대해 국제규격에 부합화된 KS ISO규격과의 일원화에 관해 연구하였다. KS규격 23,000여종을 대상으로 먹는 물 및 실내공기질관련 KS 규격을 조사하였다. 환경분야관련 KS규격은 KS I로 분류되며, 총 653종으로 조사되었으며, 이중 국제규격에 부합화된 KS I 규격은 583종으로 조사되었다. 먹는 물 수질공정 시험기준은 총 100개 기준을 대상으로 ISO/TC 147 "Water Quality" 관련 KS 규격 총 232종을 비교 검토하였으며, 실내공기질 공정시험기준은 "ISO/TC 146 "Air Quality" 관련 KS 규격 총 95종 규격을 비교 검토하였다. 문헌검토와 비교시험을 통해 먹는 물 및 실내공기질 공정시험기준과 일원화 가능한 국제규격에 부합화된 KS규격 연구결과 먹는물수질공정시험 100개 기준 중 사전일원화 완료 23개 기준, 일원화 가능 29개 기준, 일원화 불가 12개 기준, 대응 규격 없는 기준이 36개로 평가되었으며, 실내공기질 공정시험기준 17개 기준 중 사전일원화 완료 1개 기준, 일원화 가능 3개 기준, 일원화 불가 3개 기준, 대응규격 없는 기준이 10개 기준으로 평가되었다.

• 동의생리병리학회지
• /
• 제21권5호
• /
• pp.1185-1193
• /
• 2007

Ginsing polysaccharide, known to have an immune regulating effect, was administered to 23 randomly selected healthy male subjects with a mean age of 23 years in accordance with an IRB approval. Then, these subjects underwent physico-chemical tests and serum proteome was analyzed from the blood sample taken from these subjects. Analyses of proteome involved image analysis, protein sections and protein identification in sequence after two-dimensional electrophoresis was carried out. During the physico-chemical test, 4 subjects were excluded from the study. In the proteome analysis, identified were 5 spots such as SP40, 40, Cytokeratin 9, hypothetical protein LOC544932, Apolipoprotein E ,similar to Human albumin, which showed differences in the amount of protein expression. In conclusion, changes of 5 proteins were remarkable before and after administration of ginsing polysaccharides. In certain cases, hepatic and renal slight injury occurred. Thus, further clinical study on dosage regimen would be necessary for securing the basis for concentration-dependent effectiveness and safety.