• Journal of Biomedical Engineering Research
• /
• v.23 no.6
• /
• pp.477-484
• /
• 2002

A pacemaker autosense algorithm with dual thresholds. one for noise or tachyarrhythmia detection (noise threshold, NT) and the other for intrinsic beat detection (sensing threshold. ST), was developed to improve the sensing performance in single pass VDD electrograms. unipolar electrograms, or atrial fibrillation detection. When a deflection in an electrogram exceeds the NT (defined as 50% of 57), the autosense algorithm with dual thresholds checks if the deflection also exceeds the ST. If it does, the autosense algorithm calculates the signal to noise ratio (SNR) of the deflection to the highest deflection detected by NT but lower than ST during the last cardiac cycle. If the SNR 2, the autosense algorithm declares an intrinsic beat detection and calculates the next ST based on the three most recent intrinsic peaks. If the SNR $\geq$2, the autosense algorithm checks the number of deflections detected by NT during the last cardiac cycle in order to determine if it is a noise detection or tachyarrhythmia detection. Usually the autosense algorithm tries to set the 57 at 37.5% of the average of the three intrinsic beats, although it changes the percentage according to event classifications. The autosense algorithm was tested through computer simulation of atrial electrograms from 5 patients obtained during EP study, to simulate a worst sensing situation. The result showed that the ST levels for autosense algorithm tracked the electrogram amplitudes properly, providing more noise immunity whenever necessary. Also, the autosense algorithm with dual thresholds achieved sensing performance as good as the conventional fixed sensitivity method that was optimized retrospectively.

• Journal of Preventive Medicine and Public Health
• /
• v.40 no.5
• /
• pp.404-410
• /
• 2007

Objectives: Due to the assumptions of homogeneity as well as challenges in the socioeconomic position of the elderly, they have been relatively neglected in studies of health inequalities. Therefore, this study was conducted to investigate the social inequalities in preventive services among elderly men and women. Methods: Data were obtained from a nationally representative sample of 342 men and 525 women aged 65 and over collected during the 2001 National Health and Nutrition Examination Survey. Age adjusted proportions and logistic regression were used to identify the social patterning of preventive services among elderly Koreans using various social position indicators. Results: The findings of this study generally supported the presence of social gradients in preventive services among the Korean elderly. The likelihood of using the service becomes progressively higher with social position. Educational level, income, and self-rated living status were significantly associated with increased medical checkups and cancer checks. In addition, logistic regression detected educational inequalities only among older women receiving BP checks. After being stratified based on health status and chronic disease status, social disparities still existed when educational level and self-rated living status were considered. Among unhealthy individuals, place of residence was observed as a barrier to medical checkups. Conclusions: This study demonstrated strong and consistent associations between socioeconomic position and preventive services among the elderly in Korea. The results indicate that public health strategies should be developed to reduce the barriers to preventive services encountered by the elderly.

• Journal of Fashion Business
• /
• v.4 no.4
• /
• pp.41-54
• /
• 2000

The purpose of this study was to investigate various expressions in textile design using CAD and present print design of '01/02 A/W. Four steps were taken in order to achieve this purpose. The first step was to investigate prior research and to analyze textile design methods using CAD. The second step was to study '01/02 A/W fashion trend, especially textile trend. The third step was to design the print design according to textile trend and apply the designed print pattern to real model. The research results are as follows: 1. Textile design is a very important field to help making fashion industry more informative and valuable. 2. Using CAD system in textile design will be very useful and urgent in saving working time and exercising design works. 3. In '01/02 A/W hound's tooth, zigzag, herringbone will be prevalent bold geometric patterns while tartan checks, multi color stripes will be popular too. 4. Textile designs using flower, stripe, checks, dot, abstract pattern were applied to real model, the images of patterns design are as follow, flower pattern-romantic stripe-avantgarde check-cute dotclassic abstract motive-intelligent.

• Journal of the Korea Furniture Society
• /
• v.17 no.1
• /
• pp.33-46
• /
• 2006

This study was carried out to investigate a radio-frequency/vacuum (RF/V) drying ability and physical properties of the green boards and the pre-kiln dried boards with 40 mm thickness, and the 70 mm-thick green board of Iroko (Milicia excelsa). The major results were summarized as follows; The drying time from initial moisture content (MC) of 110% to approximate 6% MC for a 40mm-thick green board was 192 hours, and about 200 hours for the 70 mm-thick green board, respectively and so the RF/V drying times were dramatically shortened compared to conventional kiln drying time. The case hardenings at the RF/V drying completion stage test were very negligible, thus represented almost no existence of the residual stress. The checks were very slightly formed on all of the boards during the RF/V drying test, but crook appeared quite severely. During the accelerating test, the water-resistant treated specimens had not experienced any signs of checking occurred, whereas the control boards had encountered very frequent occurrences of end checking and slight surface checking. There were no observations of warping and discoloring regardless of the treatment.

• Journal of the Korean Wood Science and Technology
• /
• v.21 no.3
• /
• pp.61-66
• /
• 1993

24mm-thick specimens from three species of plantation-grown softwood were press dried under two platen pressures of 1.75kgf/$cm^2$ and 3.50kgf/$cm^2$ to obtain drying information regarding to drying rate, thickness shrinkage and drying defects. The influence of platen pressure on drying fare in range of moisture content (30 to 10 percent) increased for pitch pine and larch, but reduced for korean white pine at higher pressure. Thickness shrinkage was increased at the higher pressure, and estimated thickness shrinkage at final MC of 10 percent became unrealistically greater for specimens containing higher final moisture content under the great influence of compressive strain. The effects of pressure on the amount of surface checks and honeycombing were different from species used. These species should have applied lower temperature than 177$^{\circ}C$ in this study to reduce surface checks and honeycombing.

• Journal of the Korean Wood Science and Technology
• /
• v.47 no.6
• /
• pp.667-673
• /
• 2019

The performance of a wooden deck made of refractory materials that have difficulties in achieving target penetrations as stipulated in the specification and quality standards for treated wood in Korea, was assessed via a case study in this research. A wooden deck built in Jinju in 2009 was selected for this study because of its fabrication method using pressure and treated refractory materials. The penetration and retention analysis did not satisfy the domestic standard for treated wood. Inspection of the deck in 2019 revealed that the deck had been attacked by decay fungi. Cap rails showed much deeper and wider checking on their surface compared with the top and base rails, resulting in a severe fungal attack. The decking boards exhibited severe fungal decay primarily in the end parts. However, the rails and balusters without checks and posts were virtually free of fungal attack irrespective of the preservative penetration measures. Copper content in the soil 5 cm away from the deck was less than 150 mg/kg, implying that copper movement in the soil was very limited. These results suggest that the inhibition of surface propagation and the protection of end surfaces are essential factors in increasing the longevity of treated wooden decks; further, the results also showed that the deck was within an acceptable range from the point of copper contamination.

• The Research Journal of the Costume Culture
• /
• v.29 no.6
• /
• pp.932-948
• /
• 2021

Tartan, the woven, checked, and wool textile considered by many to be originally from Scotland, has in fact been in use in a range of forms across numerous cultures and during various historical periods. The characteristic checked feature is due to the assembly of different coloured threads in both warp and weft directions which intersect at 90 degrees in a combination known as a sett. For well over one hundred years, different setts and thus different colour combinations have been associated closely with different geographical regions within Scotland, as well as different clans or families. Tartan-type textiles have reached popularity at various times and those have often been a predicted fashion trend suggested, for example, by contributors to fashion gatherings such as Premier Vision in Paris. Often proposed designs are best considered based on tartan combinations rather than simple reproductions. Promotional terms such as "patched checks" or "textured checks" have been common, and often these have been derived from tartan-type constructions. This paper explores novel pattern design methods by identifying the underlying grid structures and proportions exhibited by various well-known tartan setts. The possibility of pattern development from tartan grids and their manipulations is thus the focus of attention. An insight into the methodology associated with the production of original pattern designs is thus provided.

• Smart Structures and Systems
• /
• v.32 no.4
• /
• pp.207-218
• /
• 2023

Real-time monitoring of the behavior of reinforced soil retaining wall (RSW) is required for safety checks. In this study, a targetless displacement measurement technology (TDMT) consisting of an image registration module and a displacement calculation module was proposed to monitor the behavior of RSW, in which facing displacement and settlement typically occur. Laboratory and field experiments were conducted to compare the measuring performance of natural target (NT) with the performance of artificial target (AT). Feature count- and location-based performance metrics and displacement calculation performance were analyzed to determine their correlations. The results of laboratory and field experiments showed that the feature location-based performance metric was more relevant to the displacement calculation performance than the feature count-based performance metric. The mean relative errors of the TDMT were less than 1.69 % and 5.50 % for the laboratory and field experiments, respectively. The proposed TDMT can accurately monitor the behavior of RSW for real-time safety checks.

• Journal of the Korean Wood Science and Technology
• /
• v.16 no.4
• /
• pp.10-39
• /
• 1988

This study investigated the temperatures and relative humidities in the semi-greenhouse type solar dryer with a black rock-bed heat storage and without heat storage and outdoor temperature and relative humidity at 9 a.m. and 2 p.m.. A comparison was made of the drying rates, final moisture contents, moisture content distributions, casehardening stresses, drying defects, volumetric shrinkage of dried lumber for solar- and air-drying from the green condition of mixtures of Douglas-fir, lauan, taun, oak and sycamore 25mm- and 50 mm-thick lumber during the same period for four seasons, and heat efficiencies for solar dryer with and without the heat storage for saving of heat energy and the cost of lumber drying using the solar energy. The results from this study were summarized as follows: I. The mean weekly temperatures in the solar dryers were 3 to $6^{\circ}C$ at 9 a.m. and 9 to $13^{\circ}C$ at 2 p.m. higher than mean outdoor temperature during all the drying period. 2. The mean weekly relative humidities in the solar dryers were about 1 to 19% at 9 a.m. higher than the outdoor relative humidity. and the difference between indoor and outdoor relative humidity in the morning was greater than in the afternoon. 3. The temperatures and relative humidities in the solar dryer with and without the heat storage were nearly same. 4. The overall solar insolation during the spring months was highest and then was greater in the order of summer, atumm, and winter month. S. The initial rate of solar drying was more rapid than that of air drying. As moisture content decreased, solar drying rate became more rapid than that of air drying. The rates of solar drying with and without heat storage were nearly same. The drying rate of Douglas-fir was fastest and then faster in the order of sycamore, lauan, taun and oak. and the faster drying rate of species, the smaller differences of drying rates between thicknesses of lumber. The drying rates were fastest in the summer and slowest in the winter. The rates of solar drying during the spring were more slowly in the early stage and faster in the later stage than those during the autumn. 6. The final moisture contents were above 15% for 25mm-thick air dried and about 10% for solar dried lumber, but the mean final MCs for 50mm-thick lumber were much higher than those of thin lumber. The differences of final MC between upper and lower course of pile for solar drying were greater than those of pile for air drying. The differences of moisture content between the shell and the core of air dried lumbers were greater than those of solar dried lumber, smallest in the drying during summer and greatest in the drying during winter among seasons. 7. Casehardening stresses of 25mm- and 50mm-thick dried lumber were slight, casehardening stress of solar dried lumber was severer than that of air dried lumber and was similar between solar dried lumber with and without heat storage, Casehardening stresses of lumber dried during spring were slightest and then slighter in the order of summer, autumn, and winter. Casehardening stresses of Douglas -fir, sycamore and lauan were slight, comparing with those of taun and oak. 8. Maximum initial checks of 25mm-thick lumber occurred above and below fiber saturation point and those of 50mm-thick lumber occurred in the higher moisture content than thin lumber. As the moisture content decreased, most of checks were closed and didn't show distinct difference of the degree of checks among drying methods. The degree of checks were very slight in case of Douglas-fir and lauan, and severe in case of taun and oak. The degree of checks for 50mm-thick lumber were severer than those for 25mm-thick lumber. 9. The degree of warpage showed severe in case of oak and sycamore lumber, but no warping was found in case of Douglas-fir, lauan and taun. 10. The volumetric shrinkages of taun and oak were large and medium in case of Douglas-fir, lauan and sycamore. 11. Heat efficiencies of solar dryer with heat storage were 6.9% during spring, 7.7% during summer, 12.1% during autumn and 4.1% during winter season. Heat efficiency of solar dryer with heat storage was slightly greater than that of without heat storage. As moisture content of lumber decreased, heat efficiency decreased.

• Journal of the Korean Wood Science and Technology
• /
• v.42 no.1
• /
• pp.49-57
• /
• 2014

The pre-air-drying of Korean pine before the high-temperature and low-humidity drying was shown to be effective in uniform moisture content distribution and prevention of surface check. Our results suggest that initial moisture content of the timber also plays important role in high-temperature and low-humidity drying method. The pre-air-drying also helps in the reduction of surface checks in Korean pine when compared to the Korean pine dried by only high-temperature and low-humidity. End-coating was not effective in the prevention of twist, shrinkage, case hardening and internal checks. The pre-air-drying reduces the internal tension stresses which occur during high-temperature and low-humidity drying thus decreasing case hardening and also preventing internal checks. The pre-air-drying decreases the moisture content and causes shrinkage which leads to increased twist in the Korean pine.