• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.16 no.6
• /
• pp.119-125
• /
• 2002

The temperature decrease of discharge space was very important to generate the high concentration of ozone in silent discharge type ozone generator. At this time, binding materials and methods between dielectric barrier and ground electrode affected to the discharge importantly in electrical and thermal point of view. So, above two factors become very important parameters should be considered before designing the ozone generator. In this study, binders of silicone compound, electroconductive resin and charcoal were used for variations of binders properties. Resultantly, when the binding materials were used, better ozone generation characteristics were shown(maximum ozone generation 28044［ppmV］ at 6.0［kV］) in comparison with the non-used case (maximum ozone generation 15944［ppmV］ at 4.0［kV］). In addition, when the binding materials were used, the case of pure silicone compound showed better characteristics(maximum ozone generation 28044［ppmV］ at 6.0［kV］) than the cases of conductive binding materials(maximum ozone generation 25842［ppmV］ at 5.5［kV］ and including the charcoal 5%).

• Journal of the Korean Wood Science and Technology
• /
• v.51 no.3
• /
• pp.207-221
• /
• 2023

The increasing demand for clean energy requires considerable effort to find alternative energy sources, such as briquettes. This research aims to develop a charcoal briquette with added pine resin (API) that has excellent combustion speed and distinctive aroma. Briquettes are composed of charcoal, pine resin (concentration: 0%-30%), and starch (up to 7%). They are produced in several stages, including coconut shell pyrolysis in conventional combustion, to obtain charcoal for the briquette precursor. Briquette compaction is conducted by mixing and densifying the charcoal, pine resin, and starch using a hydraulic press for 3 min. The hydraulic press has a total surface area and diameter of 57.7 cm² and 3.5 cm, respectively. The briquettes are dried at different temperatures, reaching 70℃ for 24 h. The study results show that the briquettes have a thickness and diameter of up to 2 and 3.5 cm, respectively; moisture of 2.18%-2.62%; ash of 11.61%-13.98%; volatile matter of 27.15%-51.74%; and fixed carbon content of 40.24%-59.46%. The compressive strength of the briquettes is 186-540 kg/cm². Their calorific value is 5,338-6,120 kcal/kg, combusting at a high speed of 0.15-0.40 s. The methoxy naphthalene, phenol, benzopyrrole, and lauryl alcohol; ocimene, valencene, and cembrene are found in the API. The API briquette has several chemical compounds, such as musk ambrette, ocimene, sabinene, limonene, 1-(p-cumenyl) adamantane, butane, and propanal, which improve aroma, drug application, and fuel production. Accordingly, API briquettes have considerable potential as an alternative energy source and a health improvement product.

• Asian-Australasian Journal of Animal Sciences
• /
• v.32 no.8
• /
• pp.1205-1210
• /
• 2019

Objective: The inhibitory effects of dietary antioxidants, diallyl disulfide (DADS) and quercetin, in marinade were investigated on the formation of carcinogenic polycyclic aromatic hydrocarbons (EPA priority 16 PAHs) in grilled pork. Methods: The formation of PAHs in grilled sirloin pork with different marinades after charcoal-grilling for 2 min/side were evaluated using high performance liquid chromatography with a photodiode array detector (HPLC-DAD). Results: Compared with the control marinade treatment (without antioxidant), the addition of DADS (500 mg/kg meat sample) in marinade significantly decreased benzo[a]pyrene (BaP) (100%) and heavy PAHs (84%) in charcoal-grilled pork, while the addition of quercetin at the same concentration could reduce 23% and 55% of BaP and heavy PAHs, respectively. Conclusion: The results of this study suggested that the addition of DADS in the marinade could be important in decreasing the levels of PAHs in grilled meat.

• Journal of Environmental Health Sciences
• /
• v.35 no.4
• /
• pp.315-321
• /
• 2009

Under-fired charbroiling cooking processes are known as important contributors of particulate matter (PM). In this study, we characterized the emission of particulate matters from under-fired charbroiling cooking processes using the hood method. Accumulated mass concentration of $PM_{10}$ was 92.2~99.5% and particle size of 2.0~2.5 ${\mu}m$ was highest. The concentration of PM increased very sharply at the beginning of charbroiling meats and then gradually decreased as the charbroiling continued. PM concentration also increased very sharply when gravy from meat spilled onto the frame of fire. However, mass concentration during charbroiling using only charcoals was very low compared to that of meats. We estimated the emission factors of charcoal, pork belly and pork shoulder respectively; 0.01~0.02 g/kg, 5.02~6.26 g/kg, 2.86~4.15 g/kg of $PM_{2.5}$, 0.01~0.03 g/kg, 7.44~7.91 g/kg, 4.54~5.56 g/kg of $PM_{10}$, and 0.02~0.05 g/kg, 7.59~7.95 g/kg, 4.93~5.68 g/kg of TSP. The emission factors of charcoal were negligible and the emission factors of pork belly were higher than that of pork shoulder. Emission rates of particulate matters from under-fired charbroiling cooking process were estimated as 578,009~1,265,152 kg/yr of $PM_{2.5}$, 917,539~1,598,619 kg/yr of $PM_{10}$ and 996.358~1,606,703 kg/yr of TSP. But emission factors should be verified with an in-stack cascade impactor because the reported method involves some assumptions.

• Economic and Environmental Geology
• /
• v.53 no.5
• /
• pp.529-542
• /
• 2020

The cesium (Cs) sorption characteristics of a bead-type polysulfone carrier contained HNO₃-treated bamboo charcoal (3 - 5 mm in diameter) in water system were investigated and its Cs removal efficiency as an adsorbent from water was also identified by various laboratory experiments. From the results of batch sorption experiments, the bead-type polysulfone carrier with only 5% HNO₃-treated bamboo charcoal (P-5NBC) represented the high Cs removal efficiency of 57.8% for 1 hour sorption time. The Cs removal efficiency of P-5NBC in water after 24 hours reaction maintained > 69% at a wide range of pH and temperature conditions, attesting to its applicability under various water systems. Batch sorption experiments were repeated for P-5NBC coated with two cultivated microorganisms (Pseudomonas fluorescens and Bacillus drentensis), which were typical indigenous species inhabited in soil and groundwater. The Cs removal efficiency for two microorganisms coated polysulfone carrier (BP-5NBC) additionally increased by 19% and 18%, respectively, compared to that of only P-5NBC without microorganisms coated. The average Cs desorption rate of P-5NBC for 24 h was lower than 16%, showing the Cs was stably attached on HNO₃-treated bamboo charcoal in so much as its long-term use. The maximum Cs sorption capacity (q_m) of P-5NBC calculated from the Langmuir isotherm model study was 60.9 mg/g, which was much higher than those of other adsorbents from previous studies for 1 h sorption time. The results of continuous column experiments showed that the P-5NBC coated with microorganisms packed in the column maintained > 80% of the Cs removal efficiency during 100 pore volumes flushing. It suggested that only 14.7 g of P-5NBC (only 0.75 g of HNO₃ treated bamboo charcoal included) can successfully clean-up 7.2 L of Cs contaminated water (the initial Cs concentration: 1 mg/L; the effluent concentration: < 0.2 mg/L). The present results suggested that the Cs contaminated water can be successfully cleaned up by using a small amount of the polysulfone carrier with HNO₃-treated bamboo charcoal.

• Journal of Energy Engineering
• /
• v.25 no.3
• /
• pp.9-17
• /
• 2016

In this study, a method for CO reduction using char-coal combustions was developed with lignin and glycerin as combustion improvers. The relationship between CO emission and the combustion improvers was confirmed by measuring the CO concentration. The experiment to determine the combustion characteristics was conducted using glycerin, which shows high combustibility at low temperatures, impregnated with lignin, which has a specific surface area. The combustibility, volatility, and CO concentration were measured using thermo-gravimetric analysis(TGA), and gas chromatography-mass spectrometry(GC-MS). This study presents the optimal CO reduction ratio, which occurred when the combustible material contained a 20% blend of combustion improvers. This resulted in a 20-30% CO reduction rate compared to that achieved with normal char-coal.

• Korean Journal of Agricultural Science
• /
• v.34 no.2
• /
• pp.111-117
• /
• 2007

This study was carried out to investigate the influences of feed containing activated charcoal on the performances of calves The daily weight gain, feed intake, feed requirement and the content of ammonia in the excreta were measured. The experiment was conducted with 10 male calves for 30 days. Each were equally divided with treatment group and control group and for the treatment group's animal fed diets containing 1.0% activated charcoal. The daily weight gain of calves were decreased by 1.92% when they were fed activated charcoal(1.02kg/day) compared to that of control calves(1.04kg/day) and the daily feed intake of treatment group(2.86kg/day) was 10.06% lower comparing to the control group(3.18kg/day). In case of feed requirement, the result showed 8.2% lower in the treatment group(2.80kg) than control group(3.06kg). The content of ammonia in excreta was significantly lower for treatment group(0.33ppm) than control group (2.67ppm)(p<0.05), which showed more improvement for reducing ammonia content in the treatment group with 87.6%(p<0.05).

• Journal of the Korean Wood Science and Technology
• /
• v.36 no.3
• /
• pp.93-100
• /
• 2008

For investigation of adsoption properties of cadmium elimination by wood charcoal, $25m{\ell}$ aqueous cadmium solutions in various concentrations were treated with 0.2 g wood charcoal of Red Oak (Quercus mongolica) for 280 minutes. Almost 100% of cadmium elimination ratio was obtained in the solutions with initial concentration of 20 and 40 ppm in the treatment, whereas they were 75 and 50% in those of 80 and 160 ppm. In the effect of treatment time, the highest amount of cadmium ions was eliminated during the first ten minutes in each solution so that the elimination ratio of each case was over 70% of the maximum elimination value. From the analysis of adsorptive cadmium adsorption mechanism using the Langmuir adsorption isotherm, it was suggested that cadmium ion molecules were adsorbed at the active sites on the charcoal particle in form of one layer. The Gibbs free energy of the adsorption process was calculated in negative value for each solution. This means the adsorption processes are spontaneous which do not require the extra input energy.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.7 no.1
• /
• pp.33-48
• /
• 1997

Korean diffusive sampler (KDS) and charcoal tube (CT) were used for sampling n-hexane, trichloroethylene and toluene in air KDS was made by Department of Environmental Health, SNU-SPH in 1995. Surveys were conducted at ten industrial plants with organic solvents. The relationship between two sampling methods was examined by linear regression analysis, and concentrations by two sampling methods were compared using paired t-test. The results are as follows: 1. The geometric means by CT and KDS methods were 3.26ppm and 3.32ppm for n-hexane, 5.07ppm and 6.34ppm for toluene, and 7.18ppm and 7.90ppm for toluene, respectively. There was no significant difference between results by CT and KDS methods in three organic vapors (p>0.05). When linear regression analysis was performed, two sampling methods were highly related ; correlation coefficients were 0.98, 0.90 and 0.96 for n-hexane, toluene and trichloroethylene, respectively. 2. Airborne concentrations of n-hexane (n=21) were below 0.5 TLV level. The GM by two methods were almost same (3.09 ppm). And there was no significant difference between results by two methods (p>0.05). 3. Since toluene and trichloroethylene concentrations showed several levels, appropriate sampling rates were applied for each level. The GM of toluene concentrations by two methods at 0.5 TLV level were 3.75ppm and 5.48ppm. The KDS method overestimated the toluene concentrations at 0.5 TLV level (p<0.05). The GM values of toluene concentrations at 1 TLV level were 31.80ppm and 25.38ppm and at 2 TLV level were 64.13 ppm and 51.37 ppm. The KDS method underestimated concentration at both level (p<0.05). For trichloroethylene, the GM at 0.5 TLV level were 4.97 ppm and 7.11ppm. The KDS method overestimated the concentration of trichloroethylene (p<0.05). In conclusion, concentrations of three organic vapors measured by CT and KDS were not significantly different and results by two methods were highly related. But at contain concentrations, the levels by method were significantly different. Therefore, it is suggested that sampling rate of KDS should be studied simultaneously using CT method for organic vapors.

• Journal of Plant Biotechnology
• /
• v.46 no.2
• /
• pp.119-126
• /
• 2019

This study was conducted to investigate the optimal culture method for gametophyte and sporophyte propagation in Coniogramme japonica (Thunb.) Diels, which can be used in various fields. The propagation of prothallus were cultured in 1/4 - 1 Murashige and Skoog medium and Knop medium for 10 weeks. The results indicated that the fresh weight of prothallus was the highest (14.5 g) in 1MS medium. Subsequently, various concentrations of sucrose, activated charcoal and nitrogen source were also added to 1MS medium and cultured for 8 weeks. The results provided that the sucrose concentration was 3% and the fresh weight of prothallus was the highest 10.8 g. According to the concentration in the range of 8.8 ~ 10.8 g, in the case of activated charcoal, the four treatments showed no significant difference. The nitrogen source was added at a concentration of 30, 60 and 120 mM with the ratio of ${NH_4}^+:{NO_3}^-$ being 1 : 2. As a result, the fresh weight of all treatments increased to similar level but there was no significant difference. We investigated sporophyte formation according to soil type and the highest number of sporophytes at 228.0 was formed in soils mixed with horticultural substrate and decomposed granite at 2 : 1 (v : v). On the other hand, sporophyte was not formed in soils containing peatmoss except for the one with peatmoss and decomposed granite at 2 : 1 (v : v).