• Journal of the Korean Recycled Construction Resources Institute
• /
• v.8 no.3
• /
• pp.356-364
• /
• 2020

An experimental study to investigate the effect of self-cleaning of mortar mixed with photocatalyst was performed out in this study. Test parameters included the photocatalyst content and surface roughness of the specimens. The experimental mortar specimens were manufactured by mixing a photocatalyst by cement weight of 2.5%, 5.0%, 7.5% and 10.0%. In addition, the surface roughness was categorized into three cases. They included flat surface condition, little surface roughness(medium roughness), and high surface roughness. After mortar specimens were cured for 28 days, they were illuminated by an ultraviolet lamp for 24 hours and immersed in a methylene blue conditioning solution for 12 hours. Thereafter, an ultraviolet(UV) lamp was illuminated on the specimens for 48 hours in an experimental chamber and then the color change of methylene blue solution was measured by using a spectrophotometer over illuminating time of UV lamp. The color change of methylene blue tended to increase as photocatalyst contents increased. Test results meant that photocatalyst was effective for self-cleaning in mortar. However, the color change of the methylene blue solution did not show a noticeable tendency at different surface roughness conditions. It might be due to the uneven photocatalyst distribution on the surface of mortar specimens.

• Journal of the Korea Concrete Institute
• /
• v.25 no.2
• /
• pp.137-144
• /
• 2013

The use of fiber-reinforced polymer (FRP) reinforcing bars in concrete structures has been increased as an alternative of steel reinforcement which has shown greater vulnerability to corrosion problem. However, the long-term performance of concrete members with FRP reinforcement is still questioned in comparison to the used of steel reinforcement. This study presents the results of an experimental study on the long-term behaviors of GFRP (glass fiber reinforced polymer) bar reinforced concrete beams after exposed to accelerated aging in an environmental chamber with temperature of $46^{\circ}C$ ($115^{\circ}F$) and 80% of relative humidity up to 300 days. The objectives of this research was to compare strength degradation and change of ductility between GFRP reinforced concrete beams and steel reinforcement beams after accelerated aging. Two types (wrapped and sand-coated surface) of GFRP bars and steel were reinforced. in concrete beams. Test results show that the failure modes of GFRP bar reinforced concrete beams are very similar with traditional RC beams, and the change of load-carrying capacity of steel reinforcing concrete beam is greater than that of GFRP bar reinforcing concrete beam under the accelerated aging. Test result also shows that the use of GFRP reinforcing in concrete could be introduced more brittle failure than that of steel reinforcing for practical application. The deformability factor up to compression failures indicates no significant variation before and after exposure of accelerated aging.

• Journal of IKEEE
• /
• v.24 no.1
• /
• pp.347-353
• /
• 2020

In this paper, the durability of an electromagnetic metamaterial absorber is verified in a temperature varying condition mimicking a maritime environment for the purpose of applying it to reduce the radar cross section of an integrated mast of the next-generation destroyer. To validate the durability, the reflectance of the electromagnetic metamaterial absorber was measured after storing it in a chamber that can control the temperature according to Procedure I of Method 501.7 included in MIL-STD-810H. Before and after the environmental test, both of the measured reflectances were retained less than -10 dB over the X band, that can guarantee the stealth functionality.

• Progress in Medical Physics
• /
• v.15 no.4
• /
• pp.186-191
• /
• 2004

The periodic Quality Assurance (QA) of each radiation treatment related equipments is important one, but quality assurance of the radiation treatment planning system (RTPS) is still not sufficient rather than other related equipments in clinics. Therefore, this study will present and test the periodic QA program to compare, evaluation the efficiency of the treatment planning systems. This QA program is divided to terms for the input, output devices and dosimetric data and categorized to the weekly, monthly, yearly and non-periodically with respect to the job time, frequency of error, priority of importance. CT images of the water equivalent solid phantom with a heterogeneity condition are input into the RTPS to proceed the test. The actual measurement data are obtained by using the ion chamber for the 6 MV, 10 MV photon beam, then compared a calculation data with a measurement data to evaluate the accuracy of the RTPS. Most of results for the accuracy of geometry and beam data are agreed within the error criteria which is recommended from the various advanced country and related societies. This result can be applied to the periodic QA program to improve the treatment outcome as a proper model in Korea and used to evaluate the accuracy of the RTPS.

• Restorative Dentistry and Endodontics
• /
• v.32 no.3
• /
• pp.198-207
• /
• 2007

The purpose of this study was to investigate the effect of calcium hydroxide on dentin bonding strength of various dentin bonding systems as a function of time in composite resin restoration. Dentin adhesives used in this study were Scotchbond Multipurpose, Single Bond, SE Bond and Prompt L-Pop. Flat dentin surfaces adjacent to pulp chamber were created, then $Ca(OH)_2$ and saline were mixed and applied on dentin surface of experimental group, then IRM was used to cover the mixture on dentin surface and the specimens were stored at $36.5^{\circ}C$ for experiment period (7 days, 30 days). After removing IRM and $Ca(OH)_2$, each dentin adhesives were treated on dentin surfaces. Composite resin (Z-250, 3M) was placed with S mm height and was light-cured for 20 seconds. After stored in distilled water for 24 hours, each dentin-composite bonded spicemen was embedded in epoxy resin and sectioned into $1.0\times1.0mm^2$ cross section composite-dentin beams. Specimen was mounted on zig of Universal testing machine and ${\mu}TBS$ test was performed. SEM analysis was performed to examine the fractured surfaces. The results suggested that applying calcium hydroxide did not show significant difference in dentin bonding strength.

• Journal of Korean Society of Environmental Engineers
• /
• v.32 no.10
• /
• pp.973-978
• /
• 2010

The emission of volatile organic compounds (VOCs) from building materials is one of great concerns due to maintain airtight condition of a building to reduce energy consumption, and it causes the deterioration of indoor air quality. Therefore, the emission characterization of VOCs from building materials is necessary to improve indoor air quality. Emission characteristics of VOCs from a plywood flooring that is one of the most commonly used materials in an under-heating system, and from an adhesive that is generally used to stick a plywood flooring to a concrete floor were investigated using an emission chamber test in this study. It was found that the VOCs emission factor was dependent upon and proportional to indoor temperature, and the emission characteristics were closely related to the existing places and conditions of VOCs sources inside the building materials. Maximum emission factors of hexane and toluene from building materials were generally observed at the beginning, however, only that of toluene from a plywood flooring was shown after 6 hours from the beginning. It could be considered that the existing place and condition of toluene source inside a plywood flooring could influence on the VOCs emission. From this study, bake-out time more than 72 hours could be recommended before moving in to avoid the exposure to high concentration of VOCs emitted from an under-heating system.

• Journal of Animal Environmental Science
• /
• v.11 no.1
• /
• pp.35-44
• /
• 2005

The objectives of this study were to develop an image processing algorithm for finding the sick or the dead layers(SDL) rearing in the multi-tier layer battery, which is a core technology of remote monitoring systems for layers, and to test the performance of algorithm developed in the experimental poultry housing. Based on the literature study and experiment, the standing up of layer was set as a criterion for judging layers whether sick or dead. Then, by the criterion set, an algorithm was developed. The image processing algorithm developed was tested how well it could and SDL at the experimental poultry housing. Test results showed that its monitoring correctness of layers standing up in the cages having all healthy layers was $92\%$, and $96\%$ in the cages having SDL. Therefore, it would be concluded that the image processing algorithm developed in this study was well suited to the purpose of development.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.64 no.3
• /
• pp.246-268
• /
• 2019

Soybean [Glycine max (L.) Merr.] is a species of legume native to East Asia. The interactions between climatic conditions and genetic characteristics are known to affect the agricultural performance of soybean. Therefore, the present investigation was conducted to identify the main elements affecting the agricultural performances of 11 soybean varieties/lines from China [Harbin ($45^{\circ}12^{\prime}N$), Yanji ($42^{\circ}53^{\prime}N$), Dalian ($39^{\circ}30^{\prime}N$), Qingdao ($36^{\circ}26^{\prime}N$)] and the Republic of Korea [Suwon ($37^{\circ}16^{\prime}N$), and Jeonju ($35^{\circ}49^{\prime}N$)]. The days to flowering (DTF) of soybeans with the e1-nf and e1-as alleles and the E1e2e3e4 genotype, except in 'Keumgangkong', 'Tawonkong', and 'Duyoukong', were relatively short compared to those of soybeans with other alleles. Although DTF of the soybeans was highly correlated with all climatic conditions [negative: precipitation, average temperature (AVT), accumulated temperature; positive: day-length (DL)], days to maturity and 100-seed weight of the soybeans showed no significant correlation with any climatic conditions. The soybeans with a dominant Dt1 allele, except 'Tawonkong', had the longest stem length (STL). Moreover, STL of the soybeans grown in the test fields showed a positive correlation with only DL; however, the results of our chamber test that was conducted to complement the field tests showed that STL of soybean was positively affected by AVT and DL. Although soybean yield (YLD) showed positive correlations with latitude and DL (except L62-667, OT89-5, and OT89-6), the response of YLD to the climatic conditions was cultivar-specific. Our results show that DTF and STL of soybeans grown in six different latitudes are highly affected by DL, and AVT and genetic characteristic also affect DTF and STL.

• Animal Bioscience
• /
• v.35 no.11
• /
• pp.1760-1770
• /
• 2022

Objective: It is crucial to accurately determine the net energy (NE) values of feed ingredients because the NE system is expected to be applied to the formulation of broilers feed. The NE values of 5 wheat and 5 wheat brans were determined in 12-to 14-day old Arbor Acres (AA) broilers with substitution method and indirect calorimetry method. Methods: A total of 12 diets, including 2 reference diets (REF) and 10 test diets (5 wheat diets and 5 wheat bran diets) containing 30% of test ingredients, were randomly fed to 864 male AA birds with 6 replicates of 12 birds per treatment. These birds were used to determine metabolizable energy (ME) (8 birds per replicate) in the chicken house and NE (4 birds per replicate) in the chamber respectively at the same time. After a 4-d dietary and environment adaptation period, growth performance, energy values, energy balance and energy utilization were measured during the following 3 d. Multiple linear regression analyses were further performed to generate prediction equations for NE values based on the chemical components and ME values. The NE prediction equation were also validated on another wheat diet and another wheat bran diet with high correlation (r = 0.98, r = 0.75). Results: The NE values of 5 wheat and 5 wheat bran samples are 9.34, 10.02, 10.27, 11.33, and 10.49 MJ/kg, and 5.37, 5.17, 4.87, 5.06, and 4.88 MJ/kg DM, respectively. The equation with the best fit were NE = 1.968AME-0.411×ADF-14.227 (for wheat) and NE = -0.382×CF-0.362×CP-0.244×ADF+20.870 (for wheat bran). Conclusion: The mean NE values of wheat and wheat bran are 10.29 and 5.07 MJ/kg DM in AA broilers. The NE values of ingredients could be predicted by their chemical composition and energy value with good fitness.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.22 no.5
• /
• pp.530-536
• /
• 2021

This paper presents the performance measurement results of a hybrid sheet with both shielding and heat dissipation functions developed by laminating copper mesh sheets and natural graphite sheets, which are used widely as electromagnetic shielding and heat-dissipating materials in electronic devices, without a pressure-sensitive adhesive (PSA). The results were compared by measuring the vertical and horizontal thermal conductivity with two other products to confirm the heat dissipation performance. A radiation emission test confirmed the electromagnetic shielding performance using a 3m electromagnetic anechoic chamber according to the CISPR 11 standard. In the case of vertical thermal conductivity, the proposed hybrid sheet was approximately 8.63 times higher than that of an aluminum sheet with heat dissipation coating and 18.7 times higher than that of a copper sheet laminated with artificial graphite with PSA. The proposed hybrid sheet was approximately 0.64 times that of the sheet, and approximately 1.76 times that of the heat-dissipated aluminum sheet in case of horizontal thermal conductivity. Measurements after applying each sheet in the same heat source revealed the proposed hybrid sheet to have the best heat dissipation performance. The radiation emission test showed that significantly radiation noise had been removed.