• Korean Journal of Materials Research
• /
• v.4 no.7
• /
• pp.823-827
• /
• 1994

The mechanical properties of diglycidyl ether of bisphenol A(DGEBA)/4,4- methylene dianiline(MDA) system with the addition of malononitrile(MN) and hydroquinone(HQ) were investigated. The specimens which were prepared by curing at $150^{\circ}C$ for lhr after curing at $80^{\circ}C$ for 1.5hr were tested. The effects of MN as a chain extender and HQ, a reaction accelerator on the mechanical properties were investigated. With the increase of MN and HQ contents, impact property improved significantly but tensile property decreased.

• Elastomers and Composites
• /
• v.54 no.3
• /
• pp.225-231
• /
• 2019

Bio-based polyester polyol was synthesized via esterification between azelaic acid and isosorbide. After esterification, bio-based polyurethanes were synthesized using polyester polyol, 1,3-propanediol as the chain extender, and 4,4'-diphenylmethane diisocyanate, in mixing ratios of 1:1:1.5, 1:1:1.8, 1:1:2, and 1:1:2.3. The bio TPU (Thermoplastic Polyurethane) samples were characterized by using FT-IR (Fourier Transform Infrared Spectroscopy), TGA (Thermal Gravimetric Analysis), DSC (Differential Scanning Calorimetry), and GPC (Gel Permeation Chromatography). The mechanical properties (tensile stress and hardness) were obtained by using UTM, a Shore A tester, and a Taber abrasion tester. The viscoelastic properties were tested by an Rubber Processing Analyzer in dynamic strain sweep and dynamic frequency test modes. The chemical resistance was tested with methanol by using the swelling test method. Based on these results, the bio TPU synthesized with the ratio of 1:1:2.3, referred to as TPU 4, showed the highest thermal decomposition temperature, the largest molecular weight, and most compact matrix structure due to the highest ratio of the hard segment in the molecular structure. It also presented the highest tensile strength, the largest elongation, and the best viscoelastic properties among the different bio TPUs synthesized herein.

• Transactions on Electrical and Electronic Materials
• /
• v.14 no.6
• /
• pp.308-311
• /
• 2013

The effect of an electric field on the ac electrical treeing in various epoxy/reactive diluent systems was studied in a needle-plate electrode geometry. Diglycidyl ether of bisphenol A (DGEBA) type epoxy was used as a base resin, and 1,4-butanediol diglycidyl ether (BDGE) or polyglycol (PG) as a reactive diluent was introduced to the DGEBA system, in order to decrease the viscosity of the DGEBA epoxy system. BDGE was acted as a chain extender, and PG acted as a flexibilizer, after the curing reaction. To measure the treeing initiation time and the propagation rate, three constant alternating currents (ac) of 10, 13 and 15 kV/4.2 mm (60 Hz) were applied to the specimen, in a needle-plate electrode arrangement, at $30^{\circ}C$ of insulating oil bath. When 10 kV/4.2 mm (60 Hz) was applied, the treeing initiation time and the propagation rate in the DGEBA system were 356 min and $1.10{\times}10^{-3}$ mm/min, respectively, those in the DGEBA/BDGE system were 150 min and $1.14{\times}10^{-3}$ mm/min, respectively. Those in the DGEBA/PG system were 469 min and $1.05{\times}10^{-3}$ mm/min, respectively. As 15 kV/4.2 mm (60 Hz) was applied, the propagation rate in the DGEBA system was $5.41{\times}10^{-3}$ mm/min, and that in the DGEBA/PG system was $1.42{\times}10^{-3}$ mm/min. These values meant that PG could be used as a reactive diluent in the DGEBA system, without the deterioration of the insulation breakdown property.

• Elastomers and Composites
• /
• v.42 no.2
• /
• pp.93-101
• /
• 2007

In this study, for enhancing the durability of permeable pavement material polyurethane(PU) adhesives were developed, and the physical properties upon polymerization and additives were studied. PU polymerization followed the bulk polymerization of free solvent type considering ecological aspect. Additives used in this study were carbon black, calcium carbonate and ultra violet stabilizer. The property changes upon different environment were evaluated with the compressive strength which is the principal measurement of the property of pavement materials. Among polymerized PU, one formulated with esterpolyol and crosslinkable chain extender gave the highest compressive strength of $74.9kgf/cm^2$, better than commercial $60kgf/cm^2$. The strength was the highest when the material specimen contained carbon black and calcium carbonate 20 wt%, respectively. However, UV stabilizer did not show good weathering properties.

• Journal of the Korean Chemical Society
• /
• v.27 no.1
• /
• pp.58-65
• /
• 1983

The mechanical properties (tensile strength, 100% modulus and hardness) of the urethane elastomers prepared from hydroxyl terminated polybutadiene (HTPB), several low molecular weight diols (ethylene glycol, 1, 3-propane diol, 1,4-butane diol, 1,5-pentane diol and 1,6-hexane diol) and two kinds of diisocyanates(TDI: toluene diisocyanate, IPDI: isophorone diisomechanical properties were enhanced for the increases of the concentrations of the urethane group, as predicted. In case of TDI, when the mechanical properties of the elastomers were plotted patterns were observed, which can be explained by hydrogen bondings depending on the number of the methylene carbons. But the mechanical properties of the elastomers derived from IPDI had decreasing curves against the number of methylene carbons in low molecular weight diols, without the characteristic zigzag patterns.

• Journal of the Korean Applied Science and Technology
• /
• v.29 no.1
• /
• pp.13-18
• /
• 2012

A die casting mold releasing agent was prepared from aqueous mixture of powdery carbon black and water soluble natural polymeric materials such as xanthan gum(X-gum) and carboxymethyl cellulose(CMC), which were used as thickening agent as well as curing agent with aldehydes. The suitable concentration of natural polymers for stable dispersion of carbon black in water was 0.25 wt% of X-gum or 1.0 wt% of CMC. When CMC was used less than 1 wt%, the final carbon black disperion showed a rapid phase separation. The adhesion of carbon black releasing agent on glass plate was improved with the amount of crosslinking agent, glutaraldehyde and chain extender, oligosaccharide. However, the affinity of carbon black releasing agent prepared with X-gum was stronger than that with CMC on glass plate. The final carbon black mold releasing agents prepared under our mixing conditions can be applied to the production of castings of high quality with good workability and without worthening evironmental situations.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.57 no.3
• /
• pp.226-232
• /
• 2012

Through the sampling four rice cultivars with differing amylose contents, the relationship between the structural and gelatinization properties of endosperm starches was analyzed. These rice varieties exhibited different chain length distribution ratio within the amylopectin cluster as well as varing amylose levels. The proportion of amylopectin short chains of in Goami cutlivars was higher than the other varieties, whereas the Goami 2 which shows amylose extender mutant properties in the endosperm showed the highest proportion of long chains. In X-ray diffraction analysis of rice starches, the Goami 2 variety displayed a B-type pattern whereas the other varieties were all A-type. Among the cultivars with high and normal rice starch levels, those with the higher amylose contents showed distinctly lower swelling. Goami 2 rice was found to have the highest onset and peak gelatinization temperature from the differential scanning calorimetry results. The four rice cultivars under analysis also showed different rates of hydrolysis by amyloglucosidase. These findings suggest that the composition and chemical structure of the starch content is a major determinant of both the gelatinization and functional properties of rice.

• Polymer(Korea)
• /
• v.37 no.2
• /
• pp.167-176
• /
• 2013

Linear and cross-linked waterborne polyurethanes (WPUs) based on isophorone diisocyanate and mixed diols of poly(tetramethylene glycol)/hydroxyethyl-terminated polydimethylsiloxane (PDMS-OH) were synthesized with dimethylol propionic acid as an anionic component, trimethylolpropane as a cross-linking agent, and butanediol as a chain extender and characterized. The hydrophobicity, $T_g$, stress-strain behaviors of the linear or cross-linked siloxane-containing WPU (WPU-Si) films with different PDMS content were analyzed by using water contact shape analyzer, energy dispersive spectrometer, dynamic mechanical analyzer, and universal testing machine. The results reveal that as the PDMS content increased, the hydrophobicity of WPU-Si films increased, $T_g$ moved to higher temperature, the breaking stress increased, and the breaking strain decreased.

• Clean Technology
• /
• v.23 no.2
• /
• pp.148-157
• /
• 2017

To prepare UV-curable polyurethane-acrylate oligomer, NCO-terminated urethane prepolymers with trimethylolpropane, [TMP; 0 (0), 0.1 (0.021) and 0.2 (0.043) mole (mole fraction)] as crosslinkable tri-functional chain extender were end-capped with pentaerythritol triacrylate [PETA; 2.0 (0.400), 1.7 (0.354) and 1.4 (0.304) mole (mole fraction)] with one hydroxyl group/three vinyl functionalities. The stable as-formulated UV-curable polyurethane-acrylates [stable mixtures of PETA-capped oligomer/reactive acrylic monomer diluents without/with heptadecafluorodecyl methacrylate (PFA; 0, 6 and 9 wt%)] were formed up to 0.2 (0.043) mole (mole fraction) of TMP content in the prepolymer, while homogeneous-mixing failed at 0.3 (0.068) mole (mole fraction), in which the crosslink density in NCO-terminated urethane prepolymer was too high to enable the formation of stable mixture. This study examined the effect of TMP/PETA molar ratio and heptadecafluorodecyl methacrylate (PFA) content (wt%) on the properties of UV-cured polyurethane-acrylates as marine antifouling coating materials. The properties of UV-cured polyurethane-acrylate were found to be significantly dependent on the crosslinkable TMP/PETA ratio and PFA content. With the increasing of the TMP and PFA contents, the contact angles increased, and consequently the surface tension decreased. The adhesion of algae/barnacles to PFA contained film samples were found to be sufficiently weak to allow their easy removal. These results suggest that the UV-cured samples containing PFA have strong potential as coating materials for antifouling applications.

• Polymer(Korea)
• /
• v.29 no.2
• /
• pp.177-182
• /
• 2005

Montmorillonite (MMT) modified with siloxane diamine was reacted with a reactant obtained from 4,4'-diphenyl methane diisocyanate (MDI) and polyester type polyol, $Nippollan4010(\bar{M}_n2000)$. Finally, polyurethane (PU)/MMT composites were prepared by using 1,4-butane diol as a chain extender in $25\;wt\%$ solution of N,N-dimethyl acetamide (DMAc). It was expected that these nanocomposites had superior exfoliation property to that of MMT dispersed polyurethanes produced by simple mixing due to insertion of siloxane main chain to the silicate interlayer of MMT. Extent of reaction and formation of final products were analysed by using FT-IR spectroscopy. Dispersion into the PU and intercalation of MMT were identified by applying X-ray diffraction (XRD) and transmission electron microscopy (TEM). Tensile data were acquired by universal test machine (UTM). Thermal stability and variation of surface energy were characterized by thermal gravimetric analysis (TGA) method and measurement of contact angle on the synthesized composites, respectively. As the results the organo-MMT modified with siloxane diamine in the PU composites has an intercalated structure relatively well-expanded rather than a completely exfoliated structure. The tensile strengths and the moduli for the PU/organo-MMT composites were drastically enhanced in comparison to those of $PU/Na^+-MMT$ composites.