• 한국세라믹학회지
• /
• 제47권2호
• /
• pp.195-198
• /
• 2010

It has been considered to apply GDC ($Gd_{0.1}Ce_{0.9}O_{1-X}$) for low-temperature SOFC electrolytes because it has higher ionic conductivity than YSZ at low temperature. However, open circuit voltage with using GDC ($Gd_{0.1}Ce_{0.9}O_{1-X}$) electrolyte in SOFCs, becomes lower than using YSZ (8 mol% Yttria stabilized Zirconia) electrolyte because GDC has electronic conductivity. In this work, the effect of changing GDC electrolyte thickness on the open circuit voltage has been investigated. Ni-GDC anode-supported unit cells were fabricated as follows. Mixed NiO-GDC powders were pressed and pre-sintered at $1200^{\circ}C$. And then, GDC electrolyte material was dip-coated on the anode and sintered at $1400^{\circ}C$. Finally the LSCF-GDC cathode material was screen-printed on the electrolyte and sintered at $1000^{\circ}C$. Electrolyte thickness was controlled by the number of dip-coating times. Open circuit voltage was measured depending on electrolyte thickness at $650^{\circ}C$ and found that the thicker GDC electrolyte was, the better OCV was.

• 한국전기전자재료학회논문지
• /
• 제17권12호
• /
• pp.1296-1300
• /
• 2004

SnO$_2$ is one of the most suitable gas sensor materials. The microstructure and surface morphology of films must be controlled because the electrical and optical properties of SnO$_2$ films depend on these characteristics. The effects of chemical mechanical polishing(CMP) on the variation of morphology of SnO$_2$ films prepared by RF sputtering system were investigated. The commercially developed ceria-based oxide slurry, silica-based oxide slurry, and alumina-based tungsten slurry were used as CMP slurry. Non-uniformities of all slurries met stability standards of less than 5 %. Silica slurry had the highest removal rate among three different slurries, sufficient thin film topographies and suitable root mean square(RMS) values.

• The Korean Journal of Ceramics
• /
• 제5권1호
• /
• pp.1-11
• /
• 1999

The effect of aliovalent dopents, $Nb_3O_5$ and MnO, on the grain growth kinetics of 12 mol% ceria stabilized tetragonal zirconia polycrystals (Ce-TZP) was studied. All specimens were sintered at $1550^{\circ}C$ for 20 minutes prior to annealing at different temperatures to study grain growth kinetics. Grain growth kinetics of Ce-TZP and 1 mol% $Nb_2O_5$ doped Ce-TZP (Ce-TZP/$Nb_3O_5$) during annealing at 1475, 1550, and $1600^{\circ}C$ adequately matched with square law $(D^2-D_\;o^2=k_at)$. However, grain growth in 1 mol% MnO suppressed grain growth in Ce-TZP by drag force exerted by $Mn^{+2}$ ions which segregated strongly to the positively-charged grain boundaries of Ce-TZP, $Nb_2O_5$ enhanced grain growth by increasing the concentration of vacancies of $Zr^{+4}$ ion and $Ce^{+4}$ ions. Surface analysis with X-ray photoelectron spectroscopy (XPS) showed the segregation of Mn+2 ions to grain boundaries. The kinetics of grain growth obtained in the base Ce-TZP and the Ce-TZPs with the aliovalent dopants were examined in the context of impurity drag effect and space charge effect.

• 한국세라믹학회지
• /
• 제44권10호
• /
• pp.542-547
• /
• 2007

We have determined an optimal reduction condition for NiO-based anode in single chamber solid oxide fuel cells that involve samaria-doped ceria (SDC) as an electrolyte. Optimal condition should not only induce sufficient reduction of NiO to Ni, but also prevent the reduction of SDC electrolyte in order to achieve high open circuit voltage (OCV) and power output. Thermodynamic consideration allowed us to determine the optimal anode reduction condition as $96%H_2-4%H_2O$ atmosphere at $250^{\circ}C$. This finding was in a good agreement with the experimental verifications by monitoring the conductivities of SDC and NiO under different reducing conditions.

• 신재생에너지
• /
• 제5권1호
• /
• pp.11-17
• /
• 2009

To improve the performance of the anode-supported Solid Oxide Fuel Cell (SOFC) which can be operated at an intermediate temperature, the functional layer (FL) is introduced on a anode substrate. And the scandia-stabilized zirconia (ScSZ) and samaria-doped ceria (SDC) which have higher ionic conductivity and better chemical stability than yttria-stabilized zirconia (YSZ) are used as material for the anode FL with the Ni, The fabrication process of anode-supported single cell with the anode FL was established and the power density of those was evaluated. As a result, the sample with anode FL (Ni-YSZ) has higher power density than normal cell. The single cell which was composed of the FL (Ni-YSZ) and electrolyte (YSZ) showed about $550mW/cm^2$ of the maximum power density at $650^{\circ}C$ and $1430mW/cm^2$ at $750^{\circ}C$ respectively, In case of the single cell using the ScSZ and SDC as anode FL, the performance of samples decreased rapidly and those showed unstable voltage during long-term test. In case of using methane as a fuel, the cell performance with each FL decreased comparing with $H_2$ fuel. In the region of a high current density, there are large concentration polarizations.

• 한국정밀공학회지
• /
• 제28권8호
• /
• pp.929-935
• /
• 2011

As a deterministic finishing process for the optical parts having complex surface, machining performance of the magnetorheological(MR) fluid jet polishing of optical glass are studied and compared with a general water jet polishing. First, design of the jet polishing system which has the special electromagnet-nozzle unit for stabilizing the slurry jet based on MR fluid and the change of jet shape as magnetic field is applied are explained. Second, for the BK7 glass, machining spot and its cross section profile are analyzed and the unique effect of MR fluid jet polishing is shown. Third, both material removal depth and surface roughness are explored in order to investigate the polishing performance of MR fluid jet. With the same ceria abrasives and amount in the polishing slurries, MR fluid jet shows superior machining performance compared to water jet and the difference of material removal mechanism and its resulting performance are described.

• 한국세라믹학회지
• /
• 제27권2호
• /
• pp.233-243
• /
• 1990

For theinvestigation of MgO addition effect on 12Ce-TZP ceramics, MgO-CeO2-ZrO2 ceramics was fabricated using commercial powders under sintering condition of 130$0^{\circ}C$-1$600^{\circ}C$ for 2hr. Fully tetragonal phase could be obtained by proper heat treatment and MgO addition amount. Minor cubic phase was appeared in relatively high MgO content composition at each sintering temperature. As alloying amount of MgO increased, tetragonal stability increased and grain size decreased. Grain size dependence on MgO content was verified by SEM observation of fractured surface. Surface bloating was observed from the 2 m/o to 6m/o in the temperature range of 150$0^{\circ}C$ to 1$600^{\circ}C$. In spite of very porous microstructure owing to surface bloating, 100% TZP could be maintained in 2.0m/o MgO composition by heat treatment of 150$0^{\circ}C$. This result indicated that MgO was more powerful stabilizer than CeO2. Mechanical proprties of MgO-CeO2-ZrO2 ceramics were consistent with the stability observation of tetragonal phase very well.

• 한국세라믹학회지
• /
• 제51권3호
• /
• pp.224-230
• /
• 2014

Nano-sized gadolinium-doped ceria (GDC)/nickel particle-dispersed $La_ySr_{1-y}Ti_{1-x}Fe_xO_3$ (LSFTO)-based composite solid oxide fuel cell anodes were fabricated by an infiltration method and the effects of the GDC/Ni nanoparticles on the anode polarization resistance and cell performance were investigated in terms of the infiltration time and nickel content. The anodic polarization resistance of the LSFTO anode was significantly enhanced by GDC and/or Ni infiltration and it decreased with increasing infiltration time and Ni content, respectively. It is believed that the observed phenomena are associated with enhancement of the ionic conductivity and catalytic activity in the nanocomposite anodes by the addition of GDC and Ni. Power densities of cells with the LSFTO and LSFTO-GDC/Ni nanocomposite anodes were 150 and $300mW/cm^2$ at $800^{\circ}C$, respectively.

• Environmental Analysis Health and Toxicology
• /
• 제23권2호
• /
• pp.87-91
• /
• 2008

In this study, three different sizes of cerium oxide ($CeO_2$) nanoparticles were synthesized and exposed to Caenorhabditis elegans to investigate the potential harmful effect of $CeO_2$ nanoparticles on the environment. The effects of the $CeO_2$ nanoparticles on C. elegans were assessed at multiple levels, such as with respect to stress response gene expression, growth, reproduction and mortality. Moreover, to test the ecotoxicological relevance of $CeO_2$-induced gene expression. The overall results suggest that $CeO_2$ nanoparticles may provoke ecotoxicity in C. elegans especially with respect to gene expression, reproduction and survival, which can comprise an important contribution to knowledge on the ecotoxicity of $CeO_2$ nanoparticles, about which little data are available. This is particularly valuable in the biomarker research on ecotoxicology, as ecological relevance is a crucial criterion for the applicability of the biomarker in field biomonitoring and ecological risk assessment.

• 한국세라믹학회지
• /
• 제37권10호
• /
• pp.1014-1020
• /
• 2000

RF 마크네트론 스퍼터법으로 Ce의 일부를 희토류 원소로 치환한 Ce$_{1-x}$RE$_{x}$O$_{2-y}$(0.1$\leq$x$\leq$0.4, RE=Y, Nd) 박막을 Si(111), $Al_2$O$_3$(1012) 기판 위에 1450~1$600^{\circ}C$로 소결한 target을 이용하여 성장시켰다. Ce$_{1-x}$RE$_{x}$O$_{2-y}$ 박막의 성장시 기판온도 및 증착시간 등을 변화시켜 성장시켰으며, 성장된 박막의 특성분석은 XRD, SEM, TEM으로 행하였다. 증착된 박막의 방향성 및 결정성장 거동은 증착온도 및 시간에 따라 차이를 보였다. Si(111) 기판 위에 증착된 Ce$_{1-x}$Y$_{x}$O$_{2-y}$(x=0.3) 박막의 경우, 80$0^{\circ}C$에 비해 7$50^{\circ}C$에서 증착 시간에 따른 (111) 우선배향성의 정도가 나은 결과를 보였으며, $Al_2$O$_3$(1012) 기판 위에 증착한 Ce$_{1-x}$Nd$_{x}$O$_{2-y}$(x=0.3) 박막 또는 (111) 우선배향성을 나타내었다.을 나타내었다.