• 제목/요약/키워드: ceramic tool

검색결과 224건 처리시간 0.031초

유리섬유 강화 플라스틱(GERP) 절삭시의 공구마멸 특성 (Characteristics of tool wear in cutting glass fiber reinforced plastics : the effect of physical properties of tool materials)

  • 이원평;강명순
    • 오토저널
    • /
    • 제10권1호
    • /
    • pp.33-41
    • /
    • 1988
  • A turning (facing) test on Glass Fiber Reinforced Plastics was performed with several tool materials, e.g., cemented carbides, cermet and ceramic, and the wear patterns and wear rate were analyzed to clarify the relation between physical(mechanical) properties and flank wear of cutting tool. The main results are obtained as follows: (1) When cutting speed is increased, the flank wear in every tool material grows the abnormal wear in the shape of triangle at a certain speed, i.e., a critical speed. (2) When cutting speed is increased, the wear rate in experimental tool material starts to increase remarkably at a critical speed. (3) The thermal conductivity among the properties of the tool material and the thermal crack coefficient of it are almost in proportion to the critical speed. (4) The order of performance in tool materials for cutting GFRP is K 10, M10, P20, TiC, CB.

  • PDF

선삭가공에서 초내열합금 Inconel 600의 가공성 평가 (Estimation of Machinability for Super Heat-resistant Alloys Inconel 600 in Turning Process)

  • 원종식;임은성;정윤교
    • 한국기계가공학회지
    • /
    • 제10권6호
    • /
    • pp.1-8
    • /
    • 2011
  • Recently, super heat-resistant alloy Inconel 600 come into spotlight as the material of airplane parts but this material causes lots of problems that is, reduction of machinability and attritious wear and breakage of cutting tool during turning processing due to high temperature strength and cohesion between tool material and Inconel 600. Therefore, in this study, it was purposed to determine tool material kind and to select of proper cutting range when turning process was carried out for Inconel 600. In order to these Purpose, coated carbide tool and ceramic tool was used in this experiment and the machinability of Inconel 600 was investigated from perspective of the cutting force, chipping and wear of tool and deposition phenomenon of chip.

지르코니아 코어와 전장용 세라믹의 결합 강도에 대한 표면 처리 방법 평가 (Evaluation of surface treatment methods on the bond strength of veneer ceramic to the zirconia core)

  • 이광영;홍민호
    • 대한치과기공학회지
    • /
    • 제42권3호
    • /
    • pp.213-219
    • /
    • 2020
  • Purpose: This study aimed to identify the impact of physical surface roughing with a polishing tool onto the pre-sintering yttria-stabilized tetragonal zirconia polycrystals (TZP) core and liner treatment for chemical bonding on the bond strength of TZP core and veneering ceramic. Methods: Overall, 80 specimens were classified into two groups (non-liner, NL; and usingliner, UL ) depending on the use of liner, and these two groups were then subclassified into four groups depending on the polishing tool used. (1) Non-liner groups: NS, non-liner+stone point; NC, non-liner+carbide bur; NP, non-liner+paper cone point; NT, non-liner+silicon point. (2) Using-liner groups: US, using-liner+stone point; UC, using-liner+carbide bur; UP, usingliner+paper cone point; UT, using-liner+silicon point. The pre-sintering surface roughing values and shapes were observed, and after burning up the veneering ceramic, the shear bond strength was measured using a universal testing machine. For significance testing, a one-way analysis of variance and Tukey's multiple comparison test were conducted. An optical microscope was used to observe the fracture plane, and the following results were obtained. Results: Surface roughness NP (4.09±0.51 ㎛) represented a higher value than other groups (p<0.001). In shear bond strength, NS (35.21±1.44 MPa) of the NL group showed the highest bond strength (p<0.001). The UL group did not show a statistically significant difference between groups (p=0.612). Conclusion: Our study findings reveal that the bond strength of TZP core and veneering ceramic was improved by pre-sintering physical surface treatment than by chemical bonding with liner surface treatment.

단침보강세라믹공구를 이용한 금형강(SKD61)의 선삭가공 시 표면거칠기에 영향을 미치는 인자 및 회귀방정식 도출 (Extract to Affected Factor to Surface Roughness and Regression Equation in Turning of Mold Steel(SKD61) by Whisker Reinforced Ceramic Tool)

  • 배명일;이이선;김형철
    • 한국기계가공학회지
    • /
    • 제11권4호
    • /
    • pp.118-124
    • /
    • 2012
  • In this study, we turning mold steel (SKD61) using whisker reinforced ceramic tool (WA1) to get affected factor to surface roughness and regression equation. For this study, we adapt system of experiments. Results are follows; From the analysis of variance, it was found that affected factor to surface roughness was feed rate, cutting speed, depth of cut in order. From multi-regression analysis, we calculated regression equation and the coefficient of determination($R^2$). $R^2$ was 0.978 and It means regression equation is significant. Regression equation means if feed rate increase 0.039mm/rev, surface roughness will increase $0.8391{\mu}m$, if cutting speed increase 50m/min, surface roughness will decrease $0.034{\mu}m$, if depth of cut increase 0.1mm, surface roughness will increase $0.0203{\mu}m$. From the experimental verification, it was confirmed that surface roughness was predictable by system of experiments.

금형강 가공에서 절삭력 모델에 의한 공구마멸의 예측 (The Prediction of Tool Wear by Cutting Force Model in the Machining of Die Material)

  • 조재성;강명창;김정석
    • 한국정밀공학회:학술대회논문집
    • /
    • 한국정밀공학회 1994년도 추계학술대회 논문집
    • /
    • pp.61-66
    • /
    • 1994
  • Tool condition monitoring is one of the most important aspects to improve productivity and quality and to achieve intelligent machining system. The tool state is classified into three groups as chipping, wear and fracture. In this study, wear of a ceramic cutting tool for hardened die material (SKD11) was investigated. Flank wear was occured more dominant than crarer wear. Therefore, to predict flank wear, the modeling of cutting force has been performed. The modeling of cutting force by an assumption that act the stress distribution on the tool face obtained through a numerical analysis. The relationships between the cutting force and the tool wear can be constructed by machining paraneters with cutting conditions. Experiments were performed under the various cutting conditions to ensure the validity of force models. The theoretical predictions of the flank wear is approximately in good agreement with experimental result.

  • PDF

질코니아 세라믹 연삭시 표면조도와 굽힘강도에 관한 연구 (A Study on the Surface Roughness & Bending Strength for Zirconia Ceramic Grinding)

  • 하상백
    • 한국공작기계학회:학술대회논문집
    • /
    • 한국공작기계학회 2000년도 춘계학술대회논문집 - 한국공작기계학회
    • /
    • pp.465-470
    • /
    • 2000
  • This paper is concerned with the surface roughness and the bending strength of ground workpiece in ZrO2 ceramic grinding. Surface roughness was measured with surface tracer and bending strength value was obtained by three-point bending test on machining center using tool dynamometer. Grinding experiments were carried out to examine the effects of grinding conditions including diamond mesh size, table speed, and depth of cut on ground surface roughness. The correlation between surface roughness and bending strength was also inspected. The experimental results indicate that the rougher surface was produced as the mesh size of diamond wheel is reduced and table speed is increased, but surface roughness is not affected by depth of cut. The values of bending strength decrease as the values of Ra, Rmax and Ku increase.

  • PDF

Scanning Nonlinear Dielectric Microscopy : Overview -A High Resolution Tool for Observing Ferroelectric Domains and Nano-domain Engineering-

  • Cho, Yasuo
    • 한국세라믹학회지
    • /
    • 제40권11호
    • /
    • pp.1047-1057
    • /
    • 2003
  • A sub-nanometer resolution Scanning Nonlinear Dielectric Microscope (SNDM) was developed for observing ferroelectric polarization. We also demonstrate that the resolution of SNDM is higher than that of a conventional piezo-response imaging. Secondly, we report new SNDM technique detecting higher nonlinear dielectric constants $\varepsilon$$\_$3333/ and $\varepsilon$$\_$33333/. Higher order nonlinear dielectric imaging provides higher lateral and depth resolution. Finally, the formation of artificial small inverted domain is reported to demonstrate that SNDM system is very useful as a nano-domain engineering tool. The nano-size domain dots were successfully formed in LiTaO$_3$ single crystal. This means that we can obtain a very high density ferroelectric data storage with the density above 1T-bits/inch$^2$.

자종공무마모계측시스템개발 (System Development for Automatic Tool Wear Measurement)

  • Kim, Y.I.
    • 한국정밀공학회지
    • /
    • 제11권6호
    • /
    • pp.185-199
    • /
    • 1994
  • This study has been performed to present a new automatic tool wear measurement by digital image processing. The purpose of this paper is to develop an automatic tool wear measuring system based on the image processing which can be applied to the quasi-real time measurement of the characteristics of insert tip in turning. Tool wear monitoring is one of the key-problems, for the development of control systems of modern unmanned factory which are not completely solved now. In oredr words at present complete qualitative and quantitative information on tool wear morphology is required, at least on the following aspects : flank wear, its dimensions and distribution on the maximum and mean values on VB pqrqmeter in the various zones of the wearland. crater wear, its main dimensions and values of KT parameters. This research has been performed to this technique made possible by designing a proper lighting system to the worn tool with following features : The flank wear is measured by observing the active cutting part from a proper direction and by lighting the wearland by a diffuser optic system. The crater wear is visualized by lighting the tool by a He-Ne gas laser system developed in this study. By means of this system it is research to evaluate classical parameters of tool wear and to have complete information about tool wear morphology.

  • PDF

압축성형공정에 대한 알루미나 성형체 밀도분포의 FE 분석 (FE Analysis of Alumina Green Body Density for Pressure Compaction Process)

  • 임종인;육영진
    • 한국세라믹학회지
    • /
    • 제43권12호
    • /
    • pp.859-864
    • /
    • 2006
  • For the pressure compaction process of the ceramic powder, the green density is very different with both the ceramic body shape and the processing conditions. The density difference cause non-uniform shrinkages and deformations, and make cracks in the sintered ceramics. In this paper, Material properties of the alumina powder mixed with binder and the friction coefficient between the powder and the tool set were determined through the simple compaction experiments: Also the powder flow characteristics were simulated and the green density was analyzed during the powder compaction process with Finite Element Method (FEM). The results show that the density distributions of the green body were improved at the optimized processing condition and both the possibility of the farming crack generation and rho deformation of the sintered Alumina body were reduced.

글라스 주형을 이용한 폴리머 미세 형상 핫-엠보싱 공정 연구 (Development of a Hot-Embossing Process using Ceramic Glass Molds for Polymer Micro Structures)

  • 김주한;신기훈
    • 한국공작기계학회논문집
    • /
    • 제16권6호
    • /
    • pp.168-174
    • /
    • 2007
  • A ceramic glass mold was developed for micro hot-embossing and replicated polymer parts are fabricated. The glass-ceramic micro mold could be fabricated with a laser process and a wet etching process and the fabrication time could be saved a lot. Various polymer micro structures can be obtained by hot-embossing. The process parameters such as ho-embossing temperatures or pressures were investigated and optimized. This process can be applied for fabrication of micro structures for flip-chips or micro fluidic channels for bio-engineering. The advantages and disadvantages of this process are discussed, too.