• 한국세라믹학회지
• /
• 제47권6호
• /
• pp.633-637
• /
• 2010

In this study, lithium manganese oxide spinel ($LiMn_{1.9}Fe_{0.1}Nb_{0.0005}O_4$) as a cathode material of lithium ion secondary batteries is synthesized with spray drying, and in order to increase its crystallinity and electrochemical properties, the granulated $LiMn_{1.9}Fe_{0.1}Nb_{0.0005}O_4$ particle surface is coated with lithium titanium oxide spinel ($Li_4Ti_5O_{12}$) through a sol-gel method. The granulated particles present a higher tap density and lower specific surface area. The crystallinity and discharge capacity of the $Li_4Ti_5O_{12}$ coated material is relatively higher than uncoated material. With the coating layer, the discharge capacity and cycling stability are increased and the capacity fading is suppressed successfully.

• 한국결정성장학회지
• /
• 제29권4호
• /
• pp.154-159
• /
• 2019

용융 온도를 낮추고 균질화에 영향을 줄 수 있는 yttrium oxide(산화 이트륨)과 iron oxide(산화철)를 사용하여 $LI_2O-Al_2O_3-SiO_2$ 계 결정화 유리를 제조하였다. 조핵제는 Zirconium sulfate(황산지르코늄)을 사용했고, 유리 점도를 낮추기 위해 calcium phosphate(인산칼슘)을 사용해 유리 유동성을 원활하게 하였다. 결정화 유리는 열충격 $750^{\circ}C$ 이상을 만족했고, $800^{\circ}C$ 이상에서 열팽창계수가 급격하게 상승하는 온도를 약 $30^{\circ}C$ 이상 시프트 하였다. 따라서 yttrium oxide와 iron oxide 포함하는 LAS 계 유리는 고온에서 양호한 용융 상태와 우수한 열팽창 저항성을 확인하였고 특수 주방용 재료 분야에 충분히 활용이 가능하리라 판단되었다.

• 한국세라믹학회지
• /
• 제52권5호
• /
• pp.350-355
• /
• 2015

To develop ceramic composite anodes of solid oxide fuel cells without metal catalysts, a small amount of barium carbonate was added to an $(La_{0.8}Sr_{0.2})(Cr_{0.5}Mn_{0.5})O_3(LSCM)$ - YSZ ceramic composite anode and its catalytic effects on the electrode performance were investigated. A barium precursor solution with citric acid was used to synthesize the barium carbonate during ignition, while a barium precursor solution without citric acid was used to create hydrated barium hydroxide. The addition of barium carbonate to the ceramic composite anode caused stable fuel cell performance at 1073 K; this performance was higher than that of a fuel cell with $CeO_2$ catalyst; however, the addition of hydrated barium hydroxide to the ceramic composite anode caused poor stability of the fuel cell performance.

• 한국결정성장학회지
• /
• 제28권6호
• /
• pp.263-270
• /
• 2018

최근 반도체, 디스플레이 제조장비용 세라믹소재로 대전방지 기능을 가지는 다공성 세라믹스가 시급히 요구되고 있다. 본 연구에서는 다공성 산화티탄-산화망간 기지상에 산화티탄 나노분말을 첨가하여 부분소결함으로써 $10^8-10^{10}$ ohm의 표면저항을 가지고 향상된 기계적 강도를 가지는 다공성 세라믹스를 제조하였다. 나노 크기의 산화티탄 분말을 첨가함으로써 입자 사이의 목 형성을 강화하였고, 그 결과 꺽임강도를 170 MPa(@기공률 15 %), 110 MPa(@기공률 31 %) 수준으로 증가시킬 수 있었다. 이는 P-25를 첨가하지 않았을 때의 꺽임강도(80 MPa @ 기공률 26 %)에 비하여 주목할만큼 증가한 값으로 단순한 기공률 감소가 아닌 목 형성등 미세구조 변화에 따른 것으로 판단된다. 개발 세라믹스를 적용한 OLED 유연소자 제조공정용 공기부상용 모듈을 제작하여 진공척의 성능을 평가하였다.

• 한국재료학회지
• /
• 제24권7호
• /
• pp.363-369
• /
• 2014

This is the study on diffusion of ceramic body oxide compounds to glaze. For ceramic bodies, no ferrous oxides contain white ware, celadon, and 3 wt% iron oxides contained white ware was used in this experiment. These ceramic bodies were glazed by transparency glaze, iron oxides contained glaze, and glaze made by pine tree ash that treated in 1240 degree, under reduction condition for an hour. An electron probe microanalyzer(EPMA) was used to study diffusion of oxides and to calculate distance of ceramics bodies. As a result, only iron oxide and magnesium oxide from the body diffused to glaze, and also made a band which shown very thin layer of iron oxide and magnesium oxide between the body and glaze. The densest band of iron oxide formed 100 to $150{\mu}m$ in the glaze, and the densest band of magnesium oxide was found 50 to $100{\mu}m$ in the glaze. Therefore, it could be concluded that iron oxide in the body is diffused to the glaze and it affects the color of glaze, even though iron oxide exists in the glaze. Furthermore, the thickness of the glaze has an effect on the color of celadon.

• 한국세라믹학회지
• /
• 제51권4호
• /
• pp.231-242
• /
• 2014

An interconnect in solid oxide fuel cells (SOFCs) electrically connects unit cells and separates fuel from oxidant in the adjoining cells. The interconnects can be divided broadly into two categories - ceramic and metallic interconnects. A thin and gastight ceramic layer is deposited onto a porous support, and metallic interconnects are coated with conductive ceramics to improve their surface stability. This paper provides a short review on ceramic materials for SOFC interconnects. After a brief discussion of the key requirements for interconnects, the article describes basic aspects of chromites and titanates with a perovskite structure for ceramic interconnects, followed by the introduction of dual-layer interconnects. Then, the paper presents protective coatings based on spinel-or perovskite-type oxides on metallic interconnects, which are capable of mitigating oxide scale growth and inhibiting Cr evaporation.

• 한국세라믹학회지
• /
• 제51권1호
• /
• pp.11-18
• /
• 2014

Onggi, which is described as a breathing pottery, has strongly influenced the traditional food culture in Korea. In this study Onggi is compared to porcelains including celadon and white porcelain to analyze the sources of pore formation. The differences in starting materials are examined for chemical and mineralogical compositions, particle size and distribution. The gas permeability of the fired samples is correlated to the matrix microstructure. The broad particle size distribution and high iron oxide content of Onggi are revealed as the major cause for the pore formation. Open pores are formed with large particles in the Onggi body while closed pores have a high iron oxide concentration. The Onggi body with increased open pores leads to the high gas permeability.

• Bulletin of the Korean Chemical Society
• /
• 제20권8호
• /
• pp.869-874
• /
• 1999

In this paper, electrochemical techniques are used to investigate hydrothermal-electrochemically formation of barium titanate (BT) ceramic films. For comparison, the electrochemical behaviors of anodic titanium oxide films formed in alkaline solution were also investigated both at room temperature and in hydrothermal condition at 150.0 ℃. Film structure and morphology were identified by scanning electron microscopy (SEM) and atomic force microscopy (AFM). Titanium oxide films produced at different potentials exhibit different film morphology. The breakdown of titanium oxide films anodic growth on Ti electrode plays an important roles in the formation of BT films. BT films can grow on anodic oxide/metal substrate interface by short-circuit path, and the dissolution-precipitation processes on the ceramic film/solution interface control the film structure and morphology. Based upon the current experimental results and our previous work, extensively schematic proce-dures are proposed to model the mechanism of ceramic film formation by hydrothermal-electrochemical method.

• 한국세라믹학회지
• /
• 제34권7호
• /
• pp.699-702
• /
• 1997

The cross sectional image of thin oxide failure of MOS device could be observed by Emission Microscope and Focused Ion Beam at the weak point. The oxide failures in low electric field was associated with the presence of a particle or abnormal pattern. The failures occuring at medium field are related to a pit of Si substrate. The pits could be originated from the microdefects of Cz Si wafer.

• 한국세라믹학회지
• /
• 제11권1호
• /
• pp.3-9
• /
• 1974

The role of added metal oxide in the adherence mechanism of low melting glass to several metal plates such as oxygen free high conducting copper, low carbon steel, chrominum galvanized on copper, and stainless steel was investigated. The metal oxide which added to glass were cupric oxide, ferric oxide, chromic oxide, and stainless steel oxide. The glass to that various metla oxide were added, sealed with several metal plates in the electric furnace at $650^{\circ}C$ for 5 minutes. The results as follows; 1) The interfacial reaction was promoted and strong chemical bonding with glass and metals by which the surface energy was decreased showed excellent sealing by addition of metal oxide. 2) When the interfacial reaction of glass and metals was promoted by addition of metal oxide found out that various adhernece mechanism were related to the sealing. 3) When the amount of metal oxide addition was 3-5% the excellent sealing was achieved.