• KSBB Journal
• /
• v.15 no.4
• /
• pp.388-392
• /
• 2000

An on-line glucose flow injection analysis system was developed and used for the automatic analysis and addition of glucose in the cultivationof a Saccharomyces cerevisiae in a korean paper digestion wastewater in order to increase the cell concentration. The system was composed of a ceramic sampler a sampling valve an injection valve an immobilized glucose oxidase column a debbble a flow cell with platinum electrodes a potentiostat a computer and interface system and tubing pumps. The glucose concentration of the wastewater medium was mainitained at the low concentration of $176{\pm}31 mg/L$ with the on-line FIA system and by adding glucose and $>(NH_4)_2S0_4$ the cell concentration as total cell count can be increased by 3.1times.

• Journal of the Korean Ceramic Society
• /
• v.38 no.3
• /
• pp.207-211
• /
• 2001

The effects of the sintering atmosphere and Ni content on t도 densification of TiB$_2$-Ni have been investigated. TiB$_2$powder compacts containing 10, 20, and 30 wt% Ni were liquid-phase sintered at 1500-1$700^{\circ}C$ in vacuum or in flowing Ar. The densification was enhanced as Ni content increased. For a given Ni content, the densification was faster in compacts in compacts with larger grain size. These densification behaviors agree well with the prediction of the recently developed pore-filling theory. For samples containing high Ni contents, 80TiB$_2$-20Ni and 70TiB$_2$-30Ni, the densification was faster in vacuum than in Ar. In particular, 70TiB$_2$-30Ni was fully densified at 1$700^{\circ}C$ for 60min in vacuum. The suppressed densification in Ar was due to the entrapped Ar in the isolated pores. On the other hand, for 90TiB$_2$-10Ni, the Ar-sintering resulted in higher densification than did the vacuum-sintering. This result was attributed to the suppression of Ni volatilization by the Ar in the furnace and a retarded isolation of pores due to the limited amount of liquid in the sample. Therefore, vacuum sintering is recommended for the preparation of TiB$_2$-Ni with a high Ni content while Ar sintering is recommended for the preparation of TiB$_2$-Ni with a low Ni content.

• Journal of the Korean Ceramic Society
• /
• v.54 no.4
• /
• pp.340-348
• /
• 2017

$SiC_f/SiC$ composites were joined using a $60{\mu}m-thick$ $Ti_3AlC_2$ or $Ti_3SiC_2$ MAX phase tape. The filler tape was inserted between the $SiC_f/SiC$ composites containing a 12 wt.% $Al_2O_3-Y_2O_3$ sintering additive. The joining was performed to a butt-joint configuration at $1600^{\circ}C$ or $1750^{\circ}C$ in an Ar atmosphere by applying 3.5 MPa using a hot press. Microstructural and phase analyses at the joining interface confirmed the decomposition of $Ti_3AlC_2$ and $Ti_3SiC_2$, indicating the joining by solid-state diffusion. The results showed sound joining interface without the presence of cracks. Joining strengths higher than 150 MPa could be obtained for the joints using $Ti_3AlC_2$ or $Ti_3SiC_2$ at $1750^{\circ}C$, while those for joined at $1600^{\circ}C$ decreased to 100 MPa approximately without the deformation of the joining bodies. The thickness of initial filler tape was reduced significantly after joining because of the decomposition and migration of MAX phase owing to the plasticity at high temperatures.

• Journal of the Korean Ceramic Society
• /
• v.36 no.2
• /
• pp.172-177
• /
• 1999

Graphite and carbonaceous materials showed an excellent capability as a negative electrode in Li-ion batteries because Li-ion can be intercalated and de-intercalated reversibly within most carbonaceous materials of layered structure. Also, the electrochemical potential of Li-intercalated carbon anode is almost identical with that of Li metal. In the present study, mesocarbon microbeads(MCMB) were used as anode electrode and its properties of charge/discharge and interfacial reaction with electrolyte were studied by Potentiostat/Galvanostat test, FT-IR analysis, XRD and SEM. The passivation film of solid-state was formed as the interface between electrode and electrolyte as the cell reaction began and, once formed, became thicker with repeated charge/discharge process. Also, the relationship between the passivation film formed at the electrode interface and storage capacity was discussed.

• Journal of the Korean Ceramic Society
• /
• v.39 no.5
• /
• pp.484-489
• /
• 2002

Hot-pressure sintered laminar composites with alumina/zirconia or mullite/zirconia as an outer layer and alumina/zircon (resulting in reaction-bonded mullite/zirconia during sintering) as an inner layer were fabricated by tape casting and lamination. Various forms of crack were observed in sintered laminar composites, these cracks included channel cracks in the outer layer, transverse cracks in the inner layer and interface cracks debonding interlayer. Based on detailed microscopic observations, the cracks were attributed to thermal expansion mismatch between the oxides consisting of the each layer. In particular, the interlayer and transverse cracks were confirmed in the laminates consisted of the mullite/zirconia system as the outer layers, however, those cracks were not observed in the alumina/zirconia system used. In addition, the crack propagation did not exhibit same behavior in the two kinds of outer layer when the indentation load was applied.

• Journal of Powder Materials
• /
• v.20 no.6
• /
• pp.405-410
• /
• 2013

During sintering of Ni-electrode multi-layer ceramic capacitors (MLCCs), the Ni electrode often becomes discontinuous because of its lower sintering temperature relative to that of $BaTiO_3$. In an attempt to retard the sintering of Ni, we introduced passivation of the Ni powder. To find the optimal passivation conditions, a thermogravimetric analysis (TGA) was conducted in air. After passivation at $250^{\circ}C$ for 11 h in air, a nickel oxide shell with a thickness of 4-5 nm was formed on nickel nanoparticles of 180 nm size. As anticipated, densification of the compacts of the passivated Ni/NiO core-shell powder was retarded: the starting temperature of densification increased from ${\sim}400^{\circ}C$ to ${\sim}600^{\circ}C$ in a $97N_2-3H_2$ (vol %) atmosphere. Grain growth was also retarded during sintering at temperatures of 750 and $1000^{\circ}C$. When the sintering atmosphere was changed from wet $99.93N_2-0.07H_2$ to wet $99.98N_2-0.02H_2$, the average grain size decreased at the same sintering temperature. The conductivity of the passivated powder sample sintered at $1150^{\circ}C$ for 8 h in wet $99.93N_2-0.07H_2$ was measured to be $3.9{\times}10^4S/cm$, which is comparable with that, $4.6{\times}10^4S/cm$, of the Ni powder compact without passivation. These results demonstrate that passivation of Ni is a viable means of retarding sintering of a Ni electrode and hence improving its continuity in the fabrication of $BaTiO_3$-based multi-layer ceramic capacitors.

• Journal of Technologic Dentistry
• /
• v.35 no.2
• /
• pp.137-142
• /
• 2013

Purpose: This study was to observe the surface and interfacial characteristic of Zirconia by surface treatment. And it was observed the roughness and contact angle according to processing, and the interfacial properties by surface treatment on zirconia. Methods: The oxide formation and ion diffusion between core and veneer ceramic were determined by the X-ray Dot Mapping of EPMA(Electron probe micro analyzer). The roughness was measured by 3D Digital microscope and the contact angle according to processing of zirconia was observed using distilled water on the surface. Results: The surface roughness of the specimens Z04, Z12, Z15 was measured $0.67({\pm}0.03){\mu}m$, $0.50({\pm}0.12){\mu}m$, $0.35({\pm}0.09){\mu}m$, respectively. As results of contact angle test, Z04, Z12, Z15 of specimen group without binder treatment was measured $46.79({\pm}3.17)^{\circ}$, $57.47({\pm}4.83)^{\circ}$, $56.19({\pm}2.66)^{\circ}$, respectively. but, L04, L12, L15 of specimen group without binder treatment was measured $63.84({\pm}2.20)^{\circ}$, $66.08({\pm}0.16)^{\circ}$, $65.10({\pm}1.01)^{\circ}$, respectively. Average contact angle of L15 was measured $65.10({\pm}1.01)^{\circ}$. In X-ray Dot Mapping results, thickness of binder including Al element was measured that each of L04, L12, L15 were $20{\mu}m$, $15{\mu}m$, $10{\mu}m$. Conclusion: The more rough surface increases the wettability, but the sintered exclusive binder decreases the wettability.

• Journal of the Korean Ceramic Society
• /
• v.38 no.11
• /
• pp.1000-1007
• /
• 2001

In an evacuated tube solar collector, the stable sealing of the heat pipe to the glass tube is important for the collector to use for a long period of time. The sealing of copper tube to the glass is quite difficult because of the large differences in the physical and chemical properties of the two materials. In this study, therefore, a proper copper oxide layer was induced to improve the chemical bonding of the two materials, and the oxidation state of copper and the interface between copper and glass were examined by XRD, SEM and EDS. Its bonding strength was also measured. Cu$_2$O was formed when the bare copper was heat-treated under 600$^{\circ}C$, while CuO oxide layer was formed above that temperature. The bonding state of CuO to the copper was very poor. The borate treatment of the copper, however, extend the stable forming of Cu$_2$O layer to 800$^{\circ}C$. Borosilicate glass tube was sealed to a copper tube by Housekeeper method only when the sealing part was covered with Cu$_2$O layer. The bonding strength at the interface was measured 354.4N, its thermal shock resistance was acceptable.

• Journal of the Korean Ceramic Society
• /
• v.53 no.6
• /
• pp.689-699
• /
• 2016

The effects of composition, structure design, and coating thickness of thermal barrier coating (TBC) on thermal barrier performance were investigated by measuring the temperature differences of TBC samples. TBCs with the thin and thick top coats were used for these studies, including TBCs with rare-earth (Gd, Yb, and La) compositions. The thermal barrier performance was enhanced with increasing the thickness of top coat even for thin TBCs, indicating that the thermal barrier performance was commensurate to the thickness of top coat. On the other hand, the bi-layered TBC, which was prepared with Yb-Gd-YSZ feedstock powder, with the buffer layer of high purity 8YSZ showed a better thermal barrier performance than that of regular purity 8YSZ. The interfaces in the bi-layered TBCs had a decisive effect on the thermal barrier performance, showing the performance enhanced with increasing numbers of interfaces. However, a new structural design and an additional process should be considered to reduce stress concentrations and to ensure interface stability, respectively, for improving thermal durability in the multi-layered TBCs.

• Journal of the Korean Ceramic Society
• /
• v.55 no.5
• /
• pp.446-451
• /
• 2018

In this study, different formulations of magnesium oxide and various modifiers (phosphoric acid, ferrous sulfate, pure acrylic emulsion, silicone acrylic emulsion, glass fiber, and polypropylene fiber) were used to prepare magnesium oxychloride cement composites. The compressive strength of the magnesium oxychloride cement was tested, and the softening coefficients of the composites after soaking in water were also calculated. The results showed that a magnesium oxychloride cement sample could not be coagulated when the MgO activity was 24.3%, but the coagulation effect of the magnesium oxide cement sample was excellent when the MgO activity was 69.5%. While pure acrylic emulsion, silicon-acrylic emulsion, and glass fiber showed insignificant modification effects on the magnesium oxychloride cement, ferrous sulfate heptahydrate, phosphoric acid, and polypropylene fiber could effectively improve its water resistance and compressive strength. When the phosphoric acid, ferrous sulfate heptahydrate, and polypropylene fiber contents were 0.47%, 0.73%, and 0.25%, respectively, the softening coefficient of a composite soaked in water reached 0.93 after 7 days, and the compressive strength reached 64.3 MPa.