• Journal of the Korean Ceramic Society
• /
• v.50 no.2
• /
• pp.163-167
• /
• 2013

A modified two-point impedance spectroscopy technique exploits the geometric constriction between an electrolyte and a cathode with an emphasis on semispherical-shaped electrolytes. The spatial limitation in the electrolyte/electrode interface leads to local amplification of the electrochemical reaction occurring in the corresponding electrolyte/electrode region. The modified impedance spectroscopy was applied to electrical monitoring of a YSZ ($Y_2O_3$-stabilized $ZrO_2$)/SSC ($Sm_{0.5}Sr_{0.5}CoO_3$) system. The resolved bulk and interfacial component was numerically analyzed in combination with an equivalent circuit model. The effectiveness of the "spreading resistance" concept is validated by analysis of the electrode polarization in the cathode materials of solid oxide fuel cells.

• Proceedings of the KSME Conference
• /
• 2004.11a
• /
• pp.297-301
• /
• 2004

The optimum design against contact crack initiation is investigated to find major parameters in designing desirable surface-coated asymmetric layered components. Hard ceramic coated soft materials with various elastic modulus mismatch are prepared for the analysis. Spherical indentation is conducted for producing contact cracks from the surface or interface between the coating and the substrate layer. A finite element analysis of the stress fields in the loaded layer components enables a direct correlation between the damage patterns and the stress distributions. Implications concerning the design of asymmetric layered components indicate that the coating thickness and the elastic modulus mismatch are important parameters for designing layered component to prevent the initiation of contact cracks.

• Journal of the Korean Ceramic Society
• /
• v.29 no.5
• /
• pp.377-382
• /
• 1992

For the development of solid oxide fuel cell the joined interface formation between perovskite oxygen electrode and YSZ solid electrolyte is emphasized in the aspect of reducing the undisirable overpotential. The diffusion couple of LaMnO3 and YSZ was prepared by hot pressing at 130$0^{\circ}C$ in the flow of oxygen gas. The high temperature solid state reaction mechanism between LaMnO3 and YSZ is discussed on the basis of the cation composition profile through EDX analysis. The cation components in perovskite compound diffuse considerably into YSZ, while cations of YSZ diffuse little into perovskite.

• Journal of the Korean Ceramic Society
• /
• v.30 no.5
• /
• pp.347-356
• /
• 1993

In joining alumina ceramics to metal by using Mo-Mn metallizing process the effects of metallizing thickness, temperature, and the composition of paste on the bond strength and the microstructure of joining interface were investigated. The bond strength variation in the range of metallizing temperature, 1350~155$0^{\circ}C$ was more than 150MPa above 145$0^{\circ}C$ and the optimum metallizing thickness was 30${\mu}{\textrm}{m}$. The optimum contents of Mn in Mo-Mn paste was 5% due to the bond strength decrease with the increase of addition. The effect of SiO2 addition in paste on bond strength was saturated around 200MPa. It was also observed that as the particle size of Mo decreased, the joinning with higher bond strength was shown in spite of low metallizing temperature.

• Journal of the Korean Ceramic Society
• /
• v.31 no.7
• /
• pp.731-738
• /
• 1994

TiN films were deposited on high speed steels by plasma assisted chemical vapor deposition (PACVD), cathode arc ion plating (CAIP) and reactive magnetron sputtering (RMS). The properties of the films deposited by the three different methods were compared. The preferred oriented plane of PACVD-TiN is (200) and those of CAIP-TiN and RMS-TiN are (111). PACVD-TiN shows a dome surface and a microstructure having small grains. CAIP-TiN shows the highest microhardness and the best adhesion strength of the three because it has a dense microstructure and an ill-defined interface. But is shows the greatest surface roughness due to the Ti droplet created by the arc. RMS-TiN shows a microstructure having large voids so that its properties in microhardness and adhesion are the worst of the three.

• Journal of the Korean Ceramic Society
• /
• v.31 no.11
• /
• pp.1315-1322
• /
• 1994

In this study, stable PbTiO3 coating solution was prepared using diethanolamine(DEA) complexing agent and deposited on indium-tin oxide(ITO) coated glass substrate. Prepared thin films were dense and crack-free. Perovskite-type PbTiO3 thin films could be obtained above 50$0^{\circ}C$, while the films heat-treated above $650^{\circ}C$ showed undesired properties due to interface reactions between films and substrates and warpage phenomena of substrates. Measured maximum dielectric constant and loss tangent were found to be 144 and 0.0163 at 1 kHz, 55$0^{\circ}C$ heat-treatment, respectively.

• Journal of the Korean Ceramic Society
• /
• v.31 no.7
• /
• pp.739-744
• /
• 1994

The B4C-C system was investigated to gain an understanding of the sintering behaviors of B4C. In order to get sintered density of 97% TD, sintering temperature of 225$0^{\circ}C$ was necessary. Since such a high temperature operation is actually difficult on a commercial basis, our objective was to examine the possibility of decreasing the sintering temperature by adding SiC. The addition of SiC in B4C increases the sintering rate about at 210$0^{\circ}C$ and results in a fine microstructure with more than 98% relative density on 55 wt% B4C-40wt% SiC-5 wt% C composition. The probability of liquid phase sintering was investigated, but the evidences of liquid phase formation were not observed with XRD and TEM observation. It was proposed that the addition of SiC and carbon to B4C reduce interface energy during sintering, which results in enhanced grain-boundary diffusion. Thus, the enhanced grain-boundary diffusion and retarded grain growth by SiC improve densification.

• Journal of the Korean Ceramic Society
• /
• v.32 no.6
• /
• pp.697-702
• /
• 1995

The rough growth surfaces of diamond films fabricated by the hot filament CVD were polished using thermomechanical polishing method. And then, its application to the optical windows was discussed through the measurement of transmittance in the range of infrared radiation and analysis of surfaces structure. The results were compaerd with those of the films polished with conventional mechanicla polishing. The transmittance of the mechanically polished film reached 57~66% over the whole range from 500 to 4000 cm-1. But the transmittance of the film polished with thermomechanical polishing method was reduced below 35%. This decrease in transmittance was due to both the graphitization of diamond on the polished surface and the growth of $\beta$-SiC at diamond/Si interface during polishing. The residual Fe in hte thermomechanically polished surface was confirmed by SIMS analysis. This Fe played the role of the graphitization of near surface region of the diamond film.

• Journal of the Korean Ceramic Society
• /
• v.36 no.6
• /
• pp.604-610
• /
• 1999

Silicide layer structures and morphology degradation of the surface and interface of the silicide layers for he Co/refractory metal bilayer sputter-deposited on the P-doped polycrystalline Si substrate and subjected to rapid thermal annealing were investigated and compared with those on the single Si substrate. The CoSi-CoSi2 phase transition temperature is lower an morphology degradation of the silcide layer occurs more severely for the Co/refractorymetal bilayer on the P-doped polycrystalline Si substrate than on the single Si substrate. Also the final layer structure and the morphology of the films after silicidation annealing was found to depend strongly upon the interlayer metal. The layer structure after silicidation annealing of Co/Hf/doped-poly Si is Co-Hf alloy/polycrystalline CoSi2/poly Si substrate while that of Co/Nb is polycrystalline CoSi2/NbSi2/polycrystalline CoSi2/poly Si.

• Journal of the Korean Ceramic Society
• /
• v.31 no.6
• /
• pp.678-684
• /
• 1994

The surface of alumina is capable of acquiring a change when it is in an aqueous solution. This surface change will have a strong influence on the surrounding ions, particularly those of opposite change known as the counter ions. A site-binding model of the {{{{ gamma }}-alumina/KCl(aq) interface was used to calculated theoretical surface ionization constants and P.Z.C.(Point of zero change) of {{{{ gamma }}-alumina. This paper was carried out to investigate the effect of calcination temperature on the acidic and electrical properties of pure {{{{ gamma }}-alumina prepared by the precipitation method from the Al(NO3)3.9H2O and NH4OH. From the experimental data it was shown that {{{{ gamma }}-alumina have a mainly Br nsted acid site. However, the acidity of {{{{ gamma }}-alumina decreased with increasing calcination temperature at strength Ho +9.3. The surface charge density of {{{{ gamma }}-alumina was increased with electrolyte ionic strength and calcination temperature.