• 한국태양에너지학회:학술대회논문집
• /
• 2009.11a
• /
• pp.246-250
• /
• 2009

String & tabbing step in the crystalline PV module manufacturing process for the temperature directly affects solar cells. In fact, in the manufacture of PV modules tend to be temperature factor and the corresponding changes n the output shows the same characteristics. In this journal, it will be considered about thermal characteristics, especially changes of characteristic in high temperature of the solar cell through experiment that we measure electric output characteristics of solar cells after those are applied with high temperature changes for two seconds. And we can think about the possibility of efficiency improvements over looks in PV module manufacturing processes.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.36 no.1
• /
• pp.42-48
• /
• 2023

Abstract: In this study, an induction heating system using resonance is developed to remove remaining moisture and contaminations which could be generated during fabricating secondary batteries. This system is composed of power supply and induction coil. Power supply needs an oscillator, zero crossing detection, frequency tracking function, and induction coil needs a dummy coil to obtain a uniform temperature distribution. It is very important to obtain a uniform heating temperature distribution of battery cell case in the induction heating system before pouring electrolyte into battery cell. Experimental results show a temperature distribution deviation of below 1℃ in the external position of battery cell cases. As well, the temperature of battery cell itself shows distribution of 40℃±3℃.

• Journal of the Korean Society for Geothermal and Hydrothermal Energy
• /
• v.14 no.3
• /
• pp.8-14
• /
• 2018

PV module power is calculated on PV module surface temperature adjustment by irradiation on the summer and autumn in NOCT(Nominal Operating Cell Temperature) conditions. The summer and autumn periods were selected because of large variation in outdoor air temperature and irradiation. This study was performed to understand relationship between PV module surface temperature and photovoltaic power using field measurement. As a results, it was determined that the amount of irradiation was proportional to the amount of photovoltaic power in the field measurement. However, it was also identified that the PV power generation decreased by increased PV module surface temperatures due to irradiation.

• Proceedings of the KIEE Conference
• /
• 2009.04a
• /
• pp.186-188
• /
• 2009

In this thesis, output voltage, current and power of solar module were classified by irradiation and module temperature from data of overall operating characteristics collected for one year in order to manage efficient photovoltaic generation system and deliver maximum power. In addition, from these data, correlations between irradiation, module temperature of photovoltaic cell and amount of power given by photovoltaic cell was quantitatively examined to deduce optimization of the design and construction of photovoltaic generation system. The results of this thesis can be summarized as follows. As output power characteristics according to a temperature range of 10$\sim$50[], output power was increased with an increase in temperature. Since output power increases with temperature increase, the result corresponds well to the related equation on temperature and output power.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.11 no.4
• /
• pp.1-6
• /
• 2012

This paper addresses the issue of Renewable Energy for Electricity Storage device is one of the NAS (Sodium-Sulfur) battery will be about the module. For safety reasons, not the actual battery cells using a dummy cell in the module's operating temperature setting to examine the characteristics of the insulation vacuum of the wall temperature and external temperature changes measured over time. Upper and lower boundaries of the wall vacuum insulation characteristics cotton C intervals over time, average $5^{\circ}C$, but the temperature is rising, 4C section with little temperature change did not occur. On the other hand, about $3^{\circ}C$ in section 4D, and it was confirmed that the temperature rises. Wall vacuum insulation characteristics over time to look at the experiments and measurements are described.

• Korean Chemical Engineering Research
• /
• v.62 no.3
• /
• pp.253-261
• /
• 2024

The impact of temperature on electrode reactions in 100 cm² molten carbonate cells operating as Fuel Cells (FC) and Electrolysis Cells (EC) was examined using the Reactant Gas Addition (RA) method across a temperature range of 823 to 973 K. The RA findings revealed that introduction of H₂ and CO₂, reduced the overpotential at Hydrogen Electrode (HE) in both the modes. However, no explicit temperature dependencies were observed. Conversely, adding O₂ and CO₂ to the Oxygen Electrode (OE) displayed considerable temperature dependencies in FC mode which can be attributed to increased gas solubility due to the electrolyte melting at higher temperatures. In EC mode, there was no observed temperature dependence for overpotential. Furthermore, the addition of O₂ led to a decrease in overpotential, while CO₂ addition resulted in an increased overpotential, primarily due to changes in the concentration of O₂ species.

• Journal of Hydrogen and New Energy
• /
• v.29 no.1
• /
• pp.56-63
• /
• 2018

In this study, a $100cm^2$ cell frame for a molten carbonate fuel cell was designed using CFD analysis. Electrochemical reactions, gas flow, and the heat transfer in $100cm^2$ cell frame were modeled using COMSOL Multiphysics. Two design variables such as the height of the cell frame and the length of the gas input area were determined to obtain minimized temperature distribution and uniform gas distribution. With two design parameter such as height of the cell frame and the length of the gas flow channel, the temperature difference in the cell fame was decreased to $5^{\circ}C$ and the gas uniformity in the flow channel were achieved.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.7
• /
• pp.4065-4071
• /
• 2014

The analysis results of the temperature distribution and deformation at the PV cell with a thickness of $200{\mu}m$ according to hot-air temperature at the soldering process of a PV cell and ribbon tend to agree somewhat with the experimental measured values. The best result of the electrical efficiency appears in the module soldered at a hot-air temperature of $390^{\circ}C$. An analysis of the soldering PV cell with a thickness of $150{\mu}m$ at a hot-air temperature of $350^{\circ}C$ confirmed that the maximum deformation was approximately 5.9mm. As the temperature of hot air is set to decrease, the deformation is reduced and it is predicted that the electrical efficiency can be improved.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.12 no.4
• /
• pp.449-457
• /
• 2012

The program/erase (P/E) cyclic endurances including bias temperature instability (BTI) behaviors of Metal-$Al_2O_3$-Nitride-Oxide-Semiconductor (MANOS) memories are investigated in comparison with those of Semiconductor-Oxide-Nitride-Oxide-Semiconductor (SONOS) memories. In terms of BTI behaviors, the SONOS power-law exponent n is ~0.3 independent of the P/E cycle and the temperature in the case of programmed cell, and 0.36~0.66 sensitive to the temperature in case of erased cell. Physical mechanisms are observed with thermally activated $h^*$ diffusion-induced Si/$SiO_2$ interface trap ($N_{IT}$) curing and Poole-Frenkel emission of holes trapped in border trap in the bottom oxide ($N_{OT}$). In terms of the BTI behavior in MANOS memory cells, the power-law exponent is n=0.4~0.9 in the programmed cell and n=0.65~1.2 in the erased cell, which means that the power law is strong function of the number of P/E cycles, not of the temperature. Related mechanism is can be explained by the competition between the cycle-induced degradation of P/E efficiency and the temperature-controlled $h^*$ diffusion followed by $N_{IT}$ passivation.

• Korean Journal of Environmental Biology
• /
• v.35 no.2
• /
• pp.152-159
• /
• 2017

For the effective seedling production of the hard shelled mussel, Mytilus coruscus, this study assessed the effects of the dietary value of live food, density, water temperature and salinity on growth and survival rate of the larvae. The optimal survival rate and growth rate were examined under differing conditions of water temperature, salinity, and rearing density for 30 days. The three groups were provided different feeding organisms, such as Isochrysis galbana and Teleaulax suecica. The mixtures were provided at a rate of $5{\times}10^4cell\;mL^{-1}$. The best growth was observed in the group with conditions $21^{\circ}C$ water temperature ($16.2{\pm}9.1{\mu}m$), 33 psu of salinity ($16.82{\pm}3.9{\mu}m$), $2500individual\;m^{-2}$ ($17.2{\pm}5.9{\mu}m$), and fed with $5{\times}10^4cell\;mL^{-1}$ of I. galbana and T. suecica mixture ($16.0{\pm}7.3{\mu}m$). The highest survival rate was found in the group at conditions $18^{\circ}C$ water temperature (66.4%), 33 psu of salinity (24.4%), $2500individual\;m^{-2}$ (65.8%), and fed with $5{\times}10^4cell\;mL^{-1}$ of I. galbana and T. suecica mixture (58.8%). We therefore conclude that the suitable culture conditions for the stable production of hard shelled mussel artificial seedlings was at 18 to $21^{\circ}C$ of temperature, 30 to 33 psu of salinity, 2500 to $5000individual\;m^{-2}$ of rearing density, and feeding supplement of $5{\times}10^4cell\;mL^{-1}$ of I. galbana and T. suecica mixture under semi running water system.