• 한국주조공학회지
• /
• 제3권1호
• /
• pp.13-21
• /
• 1983

In order to determine the feeding distance of aluminiun alloys (Alsi7Mg and AlCu4Ti) bar castings in the sand mold, the distance of the sound castings has been observed by radiograph for various risers, melt treatment, and casting design. Variation of porosity and hardness with the distance from the riser were also measured in order to determine the casting soundness. The results obained were as follows; 1) The modulus of riser should be 1.4 times of the casting`s 2) The maximum distance which can be made sound is greatly dependent on chemical composition and ingate location, and follows the rules given by the formula; a) When the melt flows into the casting first, and the riser afterward, D = 37.7 ${\sqrt{T}}$ for AlSi7Mg D = 31.2 ${\sqrt{T}}$ for pure aluminium D ${\ge}$ 54.8 ${\sqrt{T}}$ for AlCu4Ti Where T = casting thickness in mm Of this maximum distance, $aa{\sqrt{T}}$ for AlSi7Mg and 7.5 ${\sqrt{T}}$ for pure aluminium is made sound by the chilling effect of the casting edge. b) When the melt flows into the casting passing through the riser, $30{\times}30{\times}600mm$ bars can be made sound in all cases 3) Percentage of porosity is higer in AlCu4Ti than AlSi7Mg. And it is increased gradually by moving closer to the riser in case of $30{\times}30{\times}600mm$ bars, but for the $30{\times}30{\times}600mm$ bars it is increased gradually by moving closer to the center of bars. 4) Hardness variation is similar to the tendency of porosity. And it decreased gradually with approaching to the center in case of $30{\times}30{\times}600mm$ bars.

• 한국주조공학회지
• /
• 제35권4호
• /
• pp.80-87
• /
• 2015

The Al die casting process has been widely used in the manufacturing of automotive parts when the process requires near-net shape casting and a high productive rate. However, porosity arises in the casting process, and this hampers the wider use of this method for the creation of high-durability automotive components. The porosity can be controlled by the shot condition, but, it is critical to set the shot condition in the sleeve, and it remains difficult to optimize the shot condition to avoid air entrapment efficiently. In this study, the 4.5 mm, 2.0 mm plate die castings were fabricated under various shot conditions, such as plunger velocities of 0.7 m/s ~ 3.0 m/s and fast shot set points of the cavity of -25%, 0%, 25%, and 50%. The mold filling behavior of Al melts in the cavity was analyzed by a numerical method. Also, according to the shot conditions, the results of numerical analyses were compared to those of die-casting experiments. The porosity levels of the plate castings were analyzed by X-ray CT images and by density and microstructural analyses. The effects of the porosity on the mechanical properties were analyzed by tensile tests and hardness tests. The simulation results are in good general agreements with the die-casting experimental results. When plunger velocity and fast shot set point are 1.0 m/s and cavity 25% position, castings had optimum condition for good mechanical properties and a low level of porosity.

• 한국정보통신학회논문지
• /
• 제20권8호
• /
• pp.1546-1552
• /
• 2016

일반적으로 치과용 주조기는 불때를 이용하여 합금을 용해하기 때문에 합금의 적절한 용융온도 및 주조시간을 조절하기 어렵고 이로 인해 가스공이나 핀홀과 같은 주조결함을 발생시키며 과열로 인한 보철물의 결함을 보이고 있다. 또한 합금이 용융된 후 주조 시 대부분 투시창이나 비접촉식 온도센서를 부착하여 적절한 주조온도가 되면 작업자가 원심력을 발생하는 버튼을 눌러 도가니에 용융된 합금을 주조링에 주입한다. 이러한 결과로 대부분 주조온도가 너무 높거나 낮아서 주조결함을 많이 발생하고 있으며 균일한 주조체를 얻지 못하고 있는 실정이다. 본 논문에서는 외부의 비접촉식 온도 센서를 이용한 온도계측이 아닌 실제 합금의 사용 온도를 계측할 수 있는 단일 온도센서를 이용한 치과용 고주파 주조기를 개발하였다.

• 대한기계학회논문집A
• /
• 제35권10호
• /
• pp.1243-1248
• /
• 2011

내부결함은 주조제품의 강도 및 피로 수명에 있어 상당한 영향을 미치기 때문에 주조공정에서 주요 관심사 이다. 일반적으로 내부결함은 응력집중을 발생시키며 균열의 시작점이 되므로 피로 수명과 같은 기계적 거동에 있어 수축공과 같은 결함을 이해하는 것이 중요하다. 본 논문에서는 내부결함을 고려한 인장시편에 대해 피로시험을 수행하고 주조결함을 고려할 때의 특정하중피로노치 계수를 산정하였다. 실제 내부결함은 산업용 CT 장비를 통해서 확인하였으며 확인된 결함은 형상단순화법에 의해 타원체로 단순화 하고 응력해석과 피로해석을 수행하였다. 그 결과 우리가 제안한 방법이 기계적 거동에 있어 내부결함의 영향을 조사하고 피로수명 등을 예측함에 있어 유용함을 확인할 수 있었다.

• 대한치과보철학회지
• /
• 제41권3호
• /
• pp.342-350
• /
• 2003

Statement of problem. Titanium-Nickel alloy might be used in various prosthetic restorations since it has a unique property such as super-elasticity and high fatigue resistance. However, little is known about the casting ability of this alloy. Purpose. This in vitro study compared the casting accuracy and the porosity made with different investments and various sprue designs to ascertain what casting condition would be better for the fabrication of Ti-Ni cast restorations. Material and methods. A total of 70 Ti-Ni alloy crowns were made and divided into 7 groups of 10 copings on a metal master die. For measuring the effect of the sprue numbers, two groups with one and two 8-gauge sprues were compared. Moreover, the results of the conventional sprue and the double thickness sprues were compared. Three investments were used; carbon free phosphate bonded investment, titanium investment and gypsum bonded investment. The cast restorations were evaluated at 48 points on the entire circumferential margin with a stereomicroscope measuring in micrometers. Each crown was radiographically examined for casting defects and porosity. Data on casting accuracy were analyzed using two-way and Post hoc Scheffe's comparison to determine whether significant differences existed at the 95% confidence level. Student-Newman-Keuls test were performed to identify significant differences in the number of voids. Results. The double sprueing group and double thickness group had significantly less marginal discrepancy than the single sprueing group (P<.05 and P<.01, respectively). The castings with phosphate bonded investment showed the least marginal discrepancy and the smoothest surface. The castings invested in the gypsum bonded investment had the greatest gaps in margin and the largest failure rate. The double sprueing group and phosphate bonded investment group had significantly smaller void numbers and smaller void size than the other groups. Conclusion. Within the limitations of this in vitro study, the casting accuracy of the groups using thicker, double sprue design and the phosphate bonded investment was significantly superior. Moreover, void number and size were less than other groups.

• 헤리티지:역사와 과학
• /
• 제53권2호
• /
• pp.4-23
• /
• 2020

이 연구는 우리나라 철 주조기술의 다양성과 기술 체계를 규명하기 위한 목적으로 진행되었으며, 이를 위해 고문헌 조사 및 유물 분석, 제작 도구와 제작 기술에 대한 현지 조사 그리고 주조와 거푸집에 사용된 재료의 과학 분석 등을 실시하였다. 불미기술은 송풍구인 풀무를 이용하여 주철을 녹인 뒤 그 쇳물을 토제 거푸집에 부어 주물을 완성하는 철 주조기술로 현재 유일하게 제주도에서만 전승되고 있는데, 모래 거푸집을 사용하는 육지와 비교해 토제 거푸집을 사용하고 있다는 것이 큰 차이점이라 할 수 있다. 무쇠솥 주조기술에는 석비레, 모래, 점토 등을 섞어 만든 모래 거푸집을 이용한 주물사주조법(鑄物砂鑄造法)과 점토에 볏짚과 갈대 등을 섞어 만든 토제 거푸집을 이용한 도토주조법(陶土鑄造法)이 사용되고 있다. 주물사주조법에 의한 무쇠솥 주조는 거푸집 만들기, 속심 제작, 쇳물 작업, 거푸집에 쇳물 붓기, 완성품 다듬기 등 5단계의 작업공정을 거치며, 도토주조법에 의한 무쇠솥 주조는 거푸집 만들기, 거푸집 굽기, 질먹 입히기, 쇳물 작업, 쇳물 붓기, 완성품 다듬기 등 크게 6단계의 작업 공정으로 이루어진다. 두 주조법은 거푸집의 재료, 거푸집을 불에 굽고 질먹을 입히는 제작 공정에서 차이를 보인다. 이번에 연구한 불미기술은 토제 거푸집 무쇠솥 주조로 진흙 채취 및 반죽, 거푸집 제작, 초벌 굽기, 화적모살 및 질먹 바르기, 건조 및 비얄질, 거푸집 합장, 둑(용광로)제작, 재벌 굽기, 제련, 쇳물 붓기, 주물 다듬기 등 단계별 주조 공정에 사용된 재료 및 도구 분석과 제작 기술에 담겨진 과학 기술 원리를 규명하여 우리 고유 철 주조기술의 기술 체계를 밝혀 보았다. 그리고 무쇠솥 도토주조를 위해 이용한 재료와 완성품을 과학 분석한 결과, 거푸집은 주성분이 SiO₂, Al₂O₃, Fe₂O₃으로 이루어진 진흙과 모래이고, 이형재는 SiO₂, Al₂O₃, Fe₂O₃, K₂O가 함유된 흑연이며, 완성된 무쇠솥의 미세 조직은 시멘타이트(Fe₃C)와 펄라이트(페라이트와 시멘타이트의 층상 구조)로 이루어진 백주철 조직임을 확인하였다.

• 한국주조공학회지
• /
• 제24권4호
• /
• pp.225-230
• /
• 2004

Computer simulation of mold filling and solidification has been performed in order to analyze the flow and solidification phenomena for the casting process of cylinder liner. The simulation result of mold filling shows that the molten metal flows into the mold in stable without scattering. The simulation results of solidification indicate that the last solidified area is located in the feeder. The temperature variation in casting is measured in actual casting and the result is compared with calculation result.

• 대한기계학회논문집B
• /
• 제21권3호
• /
• pp.445-456
• /
• 1997

Continuous casting process is numerically analyzed using the continuum model in a non-orthogonal coordinate system. Flow damping in the mush is modeled by combining the viscosity dependence on liquid fraction in dilute mush and the permeability dependence on liquid fraction in concentrated mush. The effect of turbulence is indirectly considered by effective diffusivity determined elsewhere by experiment. The main objective is to investigate the effects of casting parameters such as casting speed and tundish superheat on the distribution of surface temperature, shell thickness, metallurgical length and centerline segregation. Some of the computed results are compared with available experiments, and reasonable agreements are obtained.

• 동력기계공학회지
• /
• 제7권4호
• /
• pp.44-48
• /
• 2003

Alumium alloys casting are gaining increased acceptance in the automotive and electronic industeries and squeeze casting is the most efficient method of manufacturing such mass produced parts. This study has been investigated the microstructures and mechanical properties of Al-7.0Si-0.4Mg(AC4C)alloy fabricated by squeeze casting process for development of Engine Mountain Bracket. The microstructure of squeeze casted specimen were composed of eutectic structure Alumimim solid solution and $Mg_2Si$ precipitates. The tensile strength of as-solid solution treatment Al-7.0Si-0.4Mg alloy revealed 2985MPa. It was found that Al-7.0Si-0.4Mg alloy have good aging hardening effect results are presented to show the validity of the control method.

• 대한치과의사협회지
• /
• 제10권12호
• /
• pp.809-812
• /
• 1972

This present paper is concerned with four unit fixed bridge construction by one piece casting technique in the case of missing of upper left second premolar and first molar. The authors had good clinical results with following advantages. 1. The complete bridge can be delivered to the patient for two appointments. 2. The laboratory procedures for solder joint are not necessary. 3. A one piece casting can be properly shaped without weak joints. 4. The casting can be heat-treated to insure an ideal molecular structure. 5. Porcelain veneers can be applied without weakening or melting solder joints.