• 한국강구조학회 논문집
• /
• 제27권1호
• /
• pp.87-97
• /
• 2015

본 연구에서는 균열콘크리트에 매입된 선설치앵커의 정적 전단하중에 대한 콘크리트 파열파괴강도 평가 실험을 수행하였다. 이를 위해 앵커 직경 30mm, 연단거리 150mm, 매입깊이 240mm인 비균열 시험체 2개와 전단하중에 수직한 방향과 평행한 방향의 균열을 모사한 시험체 각각 3개씩에 대해 실험을 수행하였다. 실험으로부터 하중 직각방향 균열 시험체는 비균열 시험체에 비해 강도의 저하가 없었으며 하중 평행 방향 균열 시험체는 91%의 강도를 보였는데, 이는 ACI 318-11의 비균열콘크리트의 저항강도의 84%에 해당하였다. 따라서 현재 ACI 318 기준에서 균열콘크리트의 저항강도를 비균열콘크리트 강도의 71%로 고려하는 것에 비해 작은 감소율을 보였다.

• 콘크리트학회지
• /
• 제15권3호
• /
• pp.80-86
• /
• 2003

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2000년도 봄 학술발표회 논문집
• /
• pp.167-172
• /
• 2000

In this study, the behaviors of a cast-in-situ concrete pile embedded in the weathered rock were analysed by a 3D numerical analysis using PENTAGON 3D and the results were compared with those of the field load test. The load-settlement relation and the load transfer relationship were evaluated from the numerical analysis. As a result, the load-settlement relation at the pile top and the axial load distribution with depth were predicted reasonably. And those results were similar with those of the field load test.

• Structural Engineering and Mechanics
• /
• 제36권6호
• /
• pp.745-758
• /
• 2010

12 typical laminated composite reinforced concrete (RC) walls with different concrete ages and 3 cast-in-place RC walls subjected to low frequency cyclic load were carried out in this study. The failure mode, force-deformation response and energy dissipation capacity of these specimens were investigated. Differences of structural behaviours between composite RC walls and common cast-in-place RC walls were emphasized in the analysis. The compatibility of the composite specimens with different concrete ages was discussed based on the experiment. Test results indicated that the differences between the lateral bearing capacity and the displacement ductility of the composite walls and the common walls were not so obvious. Some of the composite specimen even has higher bearing capacity under the experiment loading situation. Besides, the two parts of the laminated composite specimens demonstrates incompatibility at the later loading sequence on failure mode and strain response when it is in tension. Finally, this laminated composite shear walls are suggested to be applied in rapid reconstruction structures which is not very high.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2014년도 춘계 학술논문 발표대회
• /
• pp.10-11
• /
• 2014

Energy load of building affected by insulation performance of building's exterior. and insulation system can be classify interior insulation, exterior insulation, sandwich insulation according to install place of insulation. but within interior insulation system, corner wall and the cross outer wall-slab insulation part may occur thermal bridges. And then, within exterior insulation system is more superior insulation performance than interior insulation, but it has difficult to apply, easily broken at high building because of strong wind load. And also difficult to maintenance exterior insulation system. So, in this study, to found requirement performance of cast-in-place sandwich insulation system that is superior insulation performance and easy construction and maintenance. requirement performance of cast-in-place sandwich insulation system is 1) To avoid thermal bridges in the insulation performance, 2) Both sides concrete wall can be composite action in the structural performance. Because of this study, can develops cast-in-place sandwich insulation system and this insulation system contribute to improve insulation performance of apartment-house and high building.

• Steel and Composite Structures
• /
• 제21권5호
• /
• pp.981-997
• /
• 2016

To avoid the cracks of cast-in-place concrete in shear pockets and seams in the traditional composite beam with precast decks, this paper proposed a new type of prefabricated steel truss-concrete composite beam (ab. PSTC beam) with pre-embedded shear studs (ab. PSS connector). To study the initial cracking load of concrete deck, the development and distribution laws of the cracks, 3 PSTC beams were tested under hogging moment. And the crack behavior of the deck was compared with traditional precast composite beam, which was assembled by shear pockets and cast-in-place joints. Results show that: (i) the initial crack appears on the deck, thus avoid the appearance of the cracks in the traditional shear pockets; (ii) the crack of the seam appears later than that of the deck, which verifies the reliability of epoxy cement mortar seam, thus solves the complex structure and easily crack behavior of the traditional cast-in-place joints; (iii) the development and the distribution laws of the cracks in PSTC beam are different from the conventional composite beam. Therefore, in the deduction of crack calculation theory, all the above factors should be considered.

• 한국구조물진단유지관리공학회 논문집
• /
• 제24권2호
• /
• pp.94-102
• /
• 2020

프리캐스트 콘크리트의 장점과 및 석조 아치의 거동을 접목한 콘크리트 패널 분절 아치 시스템은 가설재가 불필요한 시공성을 확보할 수 있는 경제적 시공법이다. 분절된 프리캐스트 콘크리트 패널의 연속 배치로 구성된 아치는 인양 및 시공을 위한 V형-스트립 연결부의 선설치 앵커 설치가 필수적이다. 그러나 좁은 폭과 얇은 두께의 콘크리트 패널은 선설치 앵커의 충분한 묻힘 깊이 확보를 보장할 수 없고 앵커 인발 거동 시 패널의 휨변형을 동반하는 등 앵커 저항성능 확보를 위한 콘크리트 패널의 기하학적 영향이 고려되어야 한다. 따라서 본 연구에서는 프리캐스트 패널과 강재 아웃리거로 구성된 아치구조의 제작시 설치되는 선설치 앵커의 인발 강도 평가를 위한 실험 연구를 수행하였다. 이를 위해 실제 아치 시스템과 동일한 크기의 프리캐스트 콘크리트 패널을 제작하였으며, 선설 앵커의 직경, 앵커 묻힘 깊이, 와이어 매쉬 사용 등의 영향에 따라 총 24개 실험체의 선설치 앵커 인발 강도를 측정하였다. 또한 측정 변수에 따른 설계기준강도 확보 및 파괴 모드 평가를 통해 프리캐스트 콘크리트 패널 분절 아치 구조에 적용 가능한 선설치 앵커의 형태를 결정하였다.

• 한국해양공학회지
• /
• 제15권4호
• /
• pp.120-125
• /
• 2001

This paper describes the effect of fly ash replacement on the setting time of antiwashout underwater concrete, where cement was replaced by 0% to 50%. Experimental work was performed on the condition of sea water and in air to find out the characteristics of setting time between the concretes that were cast in air and cast in 15$^{\circ}C$ of sea water. The experimental results show that the setting time of underwater concrete with 50% replacement was delayed about 10 hours than normal concrete. And it can be concluded that, at the case of underseawater concrete addicted with fly ash, the delayed final setting times are shown as the function Tf=0.069F+7.69, where Tf is the delayed final setting time and F is quantity of fly ash, respectively. These results confirm that the setting time underseawater concrete could be prolonged.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2000년도 봄 학술발표회 논문집
• /
• pp.491-496
• /
• 2000

This paper presents the evaluation of behavior and the prediction of tensile capacity of anchors that fail concrete, as the design basis for anchorage. Tests of cast-in-place headed anchors, domestically manufactured and installed in uncracked, unreinforced concrete are performed to investigate the behavior of single anchors and multiple anchors with the consideration of various embedment lengths and edge distances. The failure mode and the load-deformation response of these anchors are discussed and the concrete failure dta are then compared with capacity predictions by the two existing methods : the 45 degree cone method of ACI 349, 318 and the concrete capacity design (CCD) method. Discrepancies between the test results and these two prediction methods, FEM analysis are assessed.

• Structural Engineering and Mechanics
• /
• 제43권5호
• /
• pp.623-636
• /
• 2012

The aim of the current work is to describe the flexural behaviour of simply supported concrete beams with tension reinforcement spliced at mid-span. The parameters included in the study were the type of the concrete, the splice length and the configuration of the hooked splice. Fifteen beams were cast using an ordinary concrete mix and two fiber reinforced concrete mixes incorporating steel and polypropylene fibers. Each concrete mix was used to cast five beams with continuous, spliced and hooked spliced tension steel bars. A test beam was reinforced on the tension side with two 12 mm bars and the splice length was 20 and 40 times the bar diameter. The hooked bars were spliced along 20 times the bar diameter and provided with 45-degree and 90-degree hooks. The test results in terms of cracking and ultimate loads, cracking patterns, ductility, and failure modes are reported. The results demonstrated the consequences due to short splices and the improvement in the structural behaviour due to the use of hooks and the confinement provided by the steel and polypropylene fibers.