• 콘크리트학회논문집
• /
• 제24권3호
• /
• pp.323-331
• /
• 2012

이 논문에서는 콘크리트 기둥에 새로운 보강방법을 제시하여 반복하중에 대한 구조적인 성능시험을 하였다. 두 개의 콘크리트 기둥에 고성능 탄소섬유 다발을 이용하여 X자 형태의 보강을 실시하고, 기둥의 내부에 X-브레이싱을 고정하기 위해 기둥 단면을 천공하여 탄소섬유 다발을 기둥에 삽입한 후 탄소섬유로 단부를 감싸주는 새로운 보강방법인 탄소섬유 앵커 X-브레이싱 보강공법을 이용해 콘크리트 기둥의 구조성능과 보강효과를 시험을 통하여 규명하였다. 이를 위해 탄소섬유로 보강된 휨 파괴형 실험체 기둥과 전단 파괴형 실험체 기둥을 축소모형으로 각각 제작하였다. 휨과 전단저항 기둥에 대해 X-브레이스 보강 유, 무 실험체에 반복하중시험을 통해 기둥의 연성과 강도 보강효과를 확인하였다.

• International Journal of Concrete Structures and Materials
• /
• 제5권1호
• /
• pp.43-48
• /
• 2011

This paper presents the performance of anchor systems for reinforced concrete beams retrofitted with carbon fiber reinforced polymer (CFRP) strips. Nine simply-supported beams are tested with various anchor systems such as steel hooks, steel plates with anchor bolts, CFRP anchor plates, and near-surface mounted (NSM) CFRP strip. The effects of these anchors on the behavior of the retrofitted beams are discussed, including load-carrying capacity, failure modes, and ductility characteristics. Test results indicate that end-anchorage is an important parameter when a CFRP-retrofit design is conducted. Mechanical bolts and NSM CRFP anchors are recommended.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1999년도 봄 학술발표회 논문집(I)
• /
• pp.727-732
• /
• 1999

In this research, we made an experiment on the 10 specimen beams that we made. The specimen beams consist of 4 steel plate strengthening beams and 5 carbon fiber sheet strengthening beams. We applied the methods of notch, rounding off a edge, anchor bolt and side shear strengening to the steel plate and for the case of carbon fiber sheet, we applied the methods of anchor bolt, line anchor and shear strengthening. After all the cases were applied, the beams was measured and analyzed about the behavior property of strengthened beams, th ability of strengthening method, the relation between load and the shape of failure, the crack load, the yield load, the shape of crack pattern, the increasing rate from yield load and maximum load and the strain of rebar. All the strengthening methods resulted in almost same value until the yield load, and it wasn't quite different from the theoretical value. In comparison with existing method, the SER, SEAS for the steel plate and the CEA, CESS, CCESS for carbon fiber sheet showed the increasement of ductility with big displacement.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1998년도 가을 학술발표대회 논문집(III)
• /
• pp.809-814
• /
• 1998

Recently many cases that using strengthening method with a steel plate or carbon-fiber sheet in a construction field are increasing. In this reason, it is demanded that developing a plan of preventing delamination of strengthening material. So in this research, for the case of strengthening method of steel plate, it is made use of notch and anchor bolt and for the case of carbon fiber sheet, it is made use of notch, anchor bolt, line anchor and shear strengthening. After all the cases were applied, we made 15 specimen beams. The beams was measured and analyzed about the behavior property of strengthened beams, the ability strengthening method, the relation between load and the shape of failure, the crack load, the yield load, the shape of crack pattern, the increasing rate from yield load and maximum load and the strain of rebar. All the strengthening methods results in almost same value until the yield load, and it wasn't quite different from the theoretical value. But for the case of increasing rate from the yield load and maximum load, comparing with the existing method, the new strengthening methods are proved to be profitable about the safety.

• 한국해양공학회지
• /
• 제14권1호
• /
• pp.52-59
• /
• 2000

Flexural fracture characteristics of newly-developed Grid-type carbon fiber plastics in the deteriorated reinforced concrete structures were investigated by the four-points fracture test to verify the strengthening effects in the beam specimens. Results showed that initial cracks appeared in the boundary layers of fibers embedded in the newly-placed mortar concrete slowly progressed to the direction of supports and showed fracture of fiber plastics and brittle failure of concrete in compression in sequence after the yielding of steel reinforcement. Accordingly the reasonable area of Grid-type carbon-fiber plastics in the strengthening design of deteriorated RC structures should be limited and given based on the ultimate strength design method to avoid the brittle failure of concrete structures.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1998년도 봄 학술발표회논문집(II)
• /
• pp.573-578
• /
• 1998

Recently, the Carbon Fiber Sheet(CFS) is widely used to strengthen the RC beams. But the behaviour of the RC beams which is strengthened with the CFS is not clearly defined yet. So, in this study we experimented with simply supported RC beams strengthened with the CFS, under monotonic loads. We included three parameters in this experiment which are the number of the sheets, the length of the sheets, and the existence of the anchor bolts. We investigated the strength effect of the RC beams by adhesion of the CFS, and the strengthening effect of CFS as to the respective parameters.

• 한국산업융합학회 논문집
• /
• 제9권4호
• /
• pp.309-315
• /
• 2006

Important material properties of UCAS rod can divide by tension characteristic of base rod part and both end part of U type anchor. Tensile properties of base rod part need as concrete reinforcement material as an alternative material of reinforcing rod, and tensile properties of U type anchor is used at connection with UCAS rod. This treatise carry out tensile test of UCAS rod, examine necessary properties such as strength, elastic modulus and maximum capacity of UCAS rod as reinforcement material of concrete. Also, to examine material properties carry out tensile test of U type anchor.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2008년도 추계 학술발표회 제20권2호
• /
• pp.453-456
• /
• 2008

섬유보강재는 부식에 대한 저항성이 높고, 고강도이며, 또한 강도에 대한 중량비(섬유보강재의 중량은 보강철근의 약 1/4정도)가 매우 낮아서 구조물 및 내하력이 저하된 콘크리트구조물의 보강에 따른 추가적인 중량의 증가 없이 보강을 할 수 있는 장점을 가지고 있다. 그러나 섬유보강재는 하중을 가하면, 최대 응력점까지 응력이 선형적으로 증가하다가 파괴되는 취성적 성질을 가지고 있다. 이러한 단점을 보완하기 위해 여러 섬유를 혼합하여 하이브리드화된 섬유보강재를 개발하였다. 개발된 하이브리드 섬유보강재는 유리섬유와 탄소섬유를 혼합하여 바 형태로 제작했으며, 유리섬유에 대한 탄소섬유의 체적비는 약 9 : 1로 구성이 된다. 하이브리드 섬유보강재를 타격식 앵커를 사용하여 시험체를 보수한 다음 인발 및 휨 시험을 실시하여 정착앵커의 수에 대한 시험체의 거동을 분석하였다. 본 연구에서는 타격식 앵커를 이용한 하이브리드 섬유보강재로 보강된 구조물의 보강특성을 알아보는데 목적이 있다.

• 한국구조물진단유지관리공학회 논문집
• /
• 제24권6호
• /
• pp.102-112
• /
• 2020

본 연구에서는 교량구조물에 활용할 수 있는 폭 100mm 이상의 대형 탄소판을 고정할 수 있는 쐐기형 정착구를 설계하기 위해서, 주요설계변수인 쐐기의 각도, 정착블록-쐐기 사이의 마찰계수 등을 기준으로 거동특성을 수치해석방법으로 분석하였다. 설계변수 별로 탄소판의 응력상태를 계산하고, 복합재료 파괴기준에 의하여 정착구의 극한상태에서의 성능을 평가하였고, 이를 바탕으로 정착구의 최적설계 제원을 결정하였다. 실물실험을 통하여 최적설계된 정착구의 성능을 검증하였으며, 본 연구의 결과는 대형 구조물을 보강하기 위한 탄소판 정착구의 최적설계에 활용될 수 있을 것으로 판단된다.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1994년도 가을 학술발표회 논문집
• /
• pp.343-349
• /
• 1994

The purpose of this study is to investigate the mechanical properties of floor slab structures with high-strength and lightweight CFRC panel using fly ash, PAN-derived and Pitch-derived carbon fiber. As a result, the flexural strength of CFRC is remarkably increased by CF contents, but compressive strength of the CFRC is not so increased as flexural strength. The bulk specific gravity is influenced by FA contents more than by CF contents, The compressive strength and the flexural strength are increased by FA contests, but decreased the case of 30% of contents. In order to increasing the flexural-carrying capacity of floor slab structures, it is recommended that the shape of anchor for reinforcement is required type-C and the spacing of anchor is required below 60mm.