• Proceedings of the Korea Committee for Ocean Resources and Engineering Conference
• /
• 2006.11a
• /
• pp.173-176
• /
• 2006

There are many kinds of protection methods for marine structures by using and environmental condition. Coating protection method, one of these methods is being widely adopted to both all ground and marine structures. In this study, by adding some additives such as Zn powder(Zn), carbon black(CB) to epoxy anti-corrosive paint, the effect to promote corrosion resistance was investigated with electrochemical method. Corrosion potentials with additives shifted to negative direction than no additive. However passivity current density increased than no additive except for Zn(20)+CB(10), especially, additive of Zn(20)+CB(10) showed the smallest passivity current density. Polarization resistance of Zn(20)+CB(10) by both cyclic voltammogram and impedance measurement was the largest value than other additives. And also surface phenomenon by adding Zn(20)+CB(10) was observed a good add condition not showing bubbling than other additives.

• Polymer(Korea)
• /
• v.34 no.5
• /
• pp.430-433
• /
• 2010

The gasket materials of for the lithium ion battery requires chemical resistance to electrolyte, electrical insulating, compression set, anti-contamination and low temperature property. To check the special characteristics of fillers which are applied to rubber for gasket, compound of EPDM, NBR and FKM (fluoro elastomer) were made by adjusting weights of carbon black and silica additive. Using these compounds, we had done tests of long-term stability against electrolyte, compression set and low-temperature property with considering operating condition of the lithium ion battery. From this test, we investigated the physical and chemical characteristics of rubber with using of carbon black and silica additive in each.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.25 no.4
• /
• pp.145-152
• /
• 2015

In this work, we were investigated the effect of the additive gases on the relationship between bonding structure and mechanical properties of the deposited films when the DLC films were deposited on Si-wafer by the rf-PECVD method with the addition of small amounts of carbon dioxide and nitrogen to the mixture gas of methane and hydrogen. The deposition rate of the films increased as the rf-power increased, while it decreased with increasing the amount of additive gases. Also, as the carbon dioxide gas increased, the hydrogen content in the films decreased but the $sp^3/sp^2$ ratio of the films increased. In case of nitrogen gas, the hydrogen content decreased, however the $sp^3/sp^2$ ratio and nitrogen gas flow rate did not show a specific tendency.

• Carbon letters
• /
• v.12 no.4
• /
• pp.218-222
• /
• 2011

Well-aligned multi-walled carbon nanotubes (MWCNTs) were successfully synthesized by catalytic chemical vapor deposition using a hydrogen sulfide ($H_2S$) additive onto Al/Fe thin film deposited on Si wafers. Transmission electron microscopy images indicated that the as-grown carbon products were thin MWCNTs with small outer diameters of less than 10 nm. $H_2S$ plays a key role in synthesizing thin MWCNTs with a large inside hollow core. The well-aligned thin MWCNTs showed a low turn-on voltage of about 1.1 V/${\mu}m$ at a current density of 0.1 ${\mu}A/cm^2$ and a high emission current of about 1.0 mA/$cm^2$ at a bias field of 2.3 V/${\mu}m$. We suggest a possible growth mechanism for the well-aligned thin MWCNTs with a large inside hollow core.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09b
• /
• pp.1216-1217
• /
• 2006

We investigated on the additive effect of carbon nanotube in the sulfur electrode on the first discharge curve and cycling property of lithium/sulfur cell. The sulfur electrode with carbon nanotube had two discharge plateau potentials and the first discharge capacity about 1200 mAh/g sulfur. The addition carbon nanotube into the sulfur electrode did not affect the first discharge behavior, but improved the cycling property of lithium/sulfur cell. The optimum content of carbon nanotube was 6 wt% of sulfur electrode

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.21 no.8
• /
• pp.79-86
• /
• 2022

With the recent increase in the demand for electric vehicles, it is necessary to identify the high current safety of automobile parts. Among the automobile parts, the EPDM parts required colored parts from the existing black; therefore, it was necessary to change the basic filler from carbon black to silica. The rubber used in automobile parts is flexible and exhibits basic characteristics of high strength and elongation. However, as the filler is changed to silica, its physical properties, such as tensile strength and elongation, are lower than those of the existing carbon black base. Therefore, it is necessary to evaluate the mechanical properties with the addition of the EPDM compound using silica as a base without degrading the physical properties of EPDM. In this study, an experiment based on the additive content was performed using the mixture experimental planning method to analyze the mechanical properties according to the additive type and mixing ratio of silica-based EPDM. The mixing ratio of the four additives was set using a simplex lattice design, and the tensile strength, elongation, modulus 300%, and permanent compression reduction rate were analyzed for mechanical characteristics, and rheometer experiments were performed for vulcanization characteristics. Through statistical analysis of the measured data, the main effects and interactions of the EPDM-blended rubber additives were analyzed. These results can be used to derive a mixing ratio of additives that satisfies the required characteristics of the EPDM compound.

• Bulletin of the Korean Chemical Society
• /
• v.30 no.2
• /
• pp.319-322
• /
• 2009

Gel polymer electrolytes were prepared by immersing a porous poly(vinylidene fluoride-co-hexafluoropropylene) membrane in an electrolyte solution containing small amounts of polymerizable additive (3,4-ethylenedioxythiophene, thiophene, biphenyl). The organic additives were electrochemically oxidized to form conductive polymer films on the electrode at high potential. With the gel polymer electrolytes containing different organic additive, lithium-ion polymer cells composed of carbon anode and LiCo$O_2$ cathode were assembled and their cycling performances were evaluated. Adding small amounts of thiophene or 3,4-ethylenedioxythiophene to the gel polymer electrolyte was found to reduce the charge transfer resistance in the cell and it thus exhibited less capacity fading and better high rate performance.

• Korean Journal of Materials Research
• /
• v.22 no.12
• /
• pp.701-705
• /
• 2012

The effects of clay, aluminum hydroxide, and carbon powder on the sintering of a Si/SiC mixture from photovoltaic silicon-wafer production were investigated. Sintering temperature was fixed at $1,350^{\circ}C$ and the sintered bodies were characterized by SEM and XRD to analyze the microstructure and to measure the apparent porosity, absorptivity, and apparent density. The XRD peak intensity of SiC in the sintered body was increased by adding 5% carbon to the Si/SiC mixture. From this result, it is confirmed that Si in the Si/SiC mixture had reacted with the added carbon. Addition of aluminum hydroxide decreased the cristobalite phase and increased the stable mullite phase. The measurement of the physical properties indicates that adding carbon to the Si/SiC mixture enables us to obtain a dense sintered body that has high apparent density and low absorptivity. The sintered body produced from the Si/SiC mixture with aluminum hydroxide and carbon powder as sintering additives can be applied to diesel particulate filters or to heat storage materials, etc., since it possesses high thermal conductivity, and anticorrosion and antioxidation properties.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2014.05a
• /
• pp.252-253
• /
• 2014

This study is to XRD and image analysis of low carbon type recycled cement from waste concrete powder and cement raw materials. Waste concrete powder possible to low carbon type recycled cement in small part of additive materials. Also, low carbon type recycled cement using waste concrete powder is suitable for ordinary portland cement.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2002.08a
• /
• pp.655-657
• /
• 2002

The carbon nanotube emitters for field emission displays were fabricated by screen printing techniques. The pastes for screen printing are composed of organic binders, carbon nanotubes, and some additive materials. Then the pastes were printed on Cr-coated/Ag-printed soda-lime glass substrates. From the I-V characteristics, the turn-on field of SWNT was lower than that of MWNT. The decrease in the mesh size of screen masks resulted in decreasing the turn-on field and increasing the electron emission current. When the carbon nanotubes were mixed with glass frit, glass frit appeared to contribute to the vertically aligning of carbon nanotubes on glass.