• Membrane Journal
• /
• v.30 no.5
• /
• pp.350-358
• /
• 2020

A membrane capacitive deionization (MCDI) cell is constructed by applying thin layer of a cation exchange membrane (Nafion) on cathode and an anion exchange membrane (aminated polyphenylene oxide, APPO) on anode. Compared to CDI cell without CEM and AEM coating, MCDI exhibits enhanced salt removal efficiency. When Nafion and APPO are used as CEM and AEM, optimized salt removal performance as high as 82.1% is observed when 1.2 V is applied for 3 min during absorption process and -1.0 V is applied for 1 min during desorption.

• Applied Chemistry for Engineering
• /
• v.31 no.5
• /
• pp.552-559
• /
• 2020

Activated carbon-nickel (II) oxide (AC-NiO) electrodes were studied as materials for the capacitive deionization (CDI) of aqueous sodium chloride solution. AC-NiO electrodes were fabricated through physical mixing and low-temperature heating of precursor materials. The amount of NiO in the electrodes was varied and its effect on the deionization performance was investigated using a single-pass mode CDI setup. The pure activated carbon electrode showed the highest specific surface area among the electrodes. However, the AC-NiO electrode with approximately 10 and 20% of NiO displayed better deionization performance. The addition of a dielectric material like NiO to the carbon material resulted in the enhancement of the electric field, which eventually led to an improved deionization performance. Among all as-prepared electrodes, the AC-NiO electrode with approximately 10% of NiO gave the highest salt adsorption capacity and charge efficiency, which are equal to 7.46 mg/g and 90.1%, respectively. This finding can be attributed to the optimum enhancement of the physical and chemical characteristics of the electrode brought by the addition of the appropriate amount of NiO.

• Membrane and Water Treatment
• /
• v.7 no.1
• /
• pp.39-53
• /
• 2016

In this study, polysufone (PSf) was used as a base polymer to synthesize sulfonated polysulfone (SPSf) and aminated polysulfone (APSf) as cation and anion exchange polymers, respectively. Then the ion exchange polymers were coated onto the surface of commercial carbon electrodes. To compare the capacitive deionization (CDI) and membrane capacitive deionization (MCDI) processes, the pristine carbon electrodes and ionic polymer coated electrodes were tested under various operating conditions such as feed flow rate, adsorption time at fixed desorption time, and feed concentration, etc., in terms of effluent concentration and salt removal efficiency. The MCDI was confirmed to be superior to the CDI process. The performance of MCDI was 2-3 times higher than that of CDI. In particular, the reverse desorption potential was a lot better than zero potential. Typically, the salt removal efficiency 100% for 100 mg/L NaCl was obtained for MCDI at feed flow rate of 15 ml/min and adsorption/desorption time of 3 min/1 min and applied voltages 1.0 V for adsorption and -0.3 V for desorption process, and for 500 mg/L, the salt removal efficiency 91% was observed.

• Journal of the Korean Society of Visualization
• /
• v.20 no.2
• /
• pp.13-20
• /
• 2022

An effective capacitive deionization process termed membrane capacitive deionization (MCDI) is newly designed and experimentally tested for seawater desalination. By preventing co-ions to be expelled, MCDI can improve the ion removal performance, but there is a trade-off between blocking co-ion transfer and increasing contact resistance. The conventional MCDI uses 2D-shaped films which increase contact resistance and reduce desalination performance in the trade-off. In this paper, with the 3-D shape of Nafion coated activated carbon cloth, the mentioned problems are expected to be solved making the desalination performance better. We visualized ion concentration and fluid flows with half-MCDI cell that can measure only efficiency of cathode. We found the optimal number of coatings which have the better efficiency than CMX, commercial cation exchange membrane in fixed current conditions of 100uA.

• Journal of the Korean Electrochemical Society
• /
• v.18 no.1
• /
• pp.24-30
• /
• 2015

To desalinate the aqueous solutions with high salt concentration using the capacitive deionization technology, two resin/membrane capacitive deionization(RMCDI) cells were fabricated by filling mixed ion exchange resins in two different flow channels (spacer and spiral type). The salt removal efficiency of the spacer- and spiral-RMCDI was 77.21 and 99.94%, respectively. Many ions were significantly removed in a spiral RMCDI cell because the feed solution could be more evenly contacted with the ion exchange resins filled on the spiral type flow channel. As the result of the changes of pH and accumulative charges, it was observed that Faradaic reaction was diminished for a spiral RMCDI cell filled by the mixture of cation and anion exchange resins. Therefore, the desalination of the aqueous solutions with high salt concentration by the capacitive deionization technology was proven. In addition, further studies on the optimization of the mixing ratio with ion exchange resins and the introduction of the regeneration process generally occurred in the continuous electrodeionization (CEDI) technology are required to improve the RMCDI technology.

• Membrane Journal
• /
• v.26 no.1
• /
• pp.62-69
• /
• 2016

In this study, sulfonated poly(ether ether ketone) (SPEEK) as cation exchange membrane and blended and crosslinked poly(vinyl amine) (PVAm) with poly(vinyl alcohol) (PVA) membrane as anion exchange membrane were used and then the performance experiments of the membrane capacitive deionization (MCDI) installed with both membranes were carried out. The newly prepared anion exchange membrane were characterized through water content, ion exchange capacity and FT-IR. The crosslinking time of 3 h to 5 h indicated that the salt removal was reduced from 81.3, 65.7% to 53.8%. The effect of PVAm contents from 40, 60, to 80% on the salt removal was shown 81.3, 75.2 and 37.7%, respectively. As a result, it was concluded that the crosslinking time and the content of PVAm had an influence on the salt removal efficiency.

• Journal of the Korean Society of Industry Convergence
• /
• v.24 no.5
• /
• pp.563-571
• /
• 2021

In this study, calcium alginate based cation exchange membrane was prepared and used to develop membrane capacitive deionization (MCDI) system for effective hardness control. As a major result, the MCDI with Ca-alginate membrane showed 27% better deionization capacity than the MCDI with a commercial cation exchange membrane. This superior improvement in the deionization capacity was expected to be due to the high ratio of transport number/electrical resistance (S_c/R_ratio) of Ca-alginate membrane. In addition, the MCDI with Ca-alginate membrane showed better deionization performance than the MCDI with Ca-alginate coating. This was because the space between the electrode and the Ca-alginate membrane was utilized for ion adsorption. The preliminary results indicated that the MCDI with Ca-alginate membrane can be a viable technique for the hardness control.

• Journal of the Korean Electrochemical Society
• /
• v.12 no.3
• /
• pp.287-294
• /
• 2009

Desalination effects of Capacitive deionization(CDI) process using activated carbon $TiO_2$ composite electrode. In this study, we made the activated carbon electrod and activated carbon $TiO_2$ composite electrode, which analysed at cyclic voltammetry and charge-discharge. The results measured for discharge capacitance in cyclic voltammetry were 125 F/g in activated carbon electrode and capacitance of activatd carbon composite electrode was increased about two time, 243 F/g. The $TiO_2$ content of activated carbon composite electrode was 10 wt.%. When it was added wtih TiO2, electric double layer adsorption content was increased, so it was increased 25% in ion removal ratio of activated carbon electrode.

• Journal of Electrochemical Science and Technology
• /
• v.6 no.4
• /
• pp.139-145
• /
• 2015

Capacitive deionization (CDI) process is a novel approach for desalination of an aqueous salt solution. In the present study, an activated carbon cloth (ACC) is proposed as effective electrode material. Initially the carbon cloth was activated in 1 M and 8 M HNO₃ for 9 hours at room temperature. The untreated and chemically activated carbon cloth (ACC) electrode materials were subjected to BET surface area measurements in order to get information about their specific surface area, average pore size, total pore volume and micropore area. The above materials were characterized by X-ray diffraction (XRD) and scanning electron microscope (SEM) also. The electrochemical studies for the electrodes were done using cyclic voltammetry (CV) in 0.1 M Na₂SO₄ medium. From the studies, it was found that resistivity of the activated carbon cloth electrodes (treated in 1 M and 8 M HNO₃) was decreased significantly by the chemical oxidation in nitric acid at room temperature and its capacitance was found to be 90 F/g (1 M HNO₃) and 154 F/g (8 M HNO₃) respectively in 0.1 M Na₂SO₄ solution. The capacitive deionization behavior of a single cell CDI with activated carbon cloth electrodes was also studied and reported in this work.

• Membrane Journal
• /
• v.29 no.6
• /
• pp.355-361
• /
• 2019

We studied the removal of barium ions that may be contained in industrial wastewater using the existing capacitive deionization (CDI). The 30 mg/L BaCl₂ (barium chloride dihydrate) solution was used as the feed solution, and the flow rate was set to 10 mL/min. The adsorption conditions were varied from 1.2 V to 3, 5 and 7 min, and the desorption conditions were -1, -1.5, -2 V and 1, 2 and 3 min, respectively, to select the most efficient conditions. As a result, barium ion removal efficiency of 64.4% was obtained under the adsorption conditions of adsorption of 1.2 V/7 min and the desorption -1 V/1 min. For the desorption voltages and time, under the same experimental conditions, the removal efficiency of CDI for 30 mg/L NaCl aqueous solution with the same concentration as barium showed 69.9% removal efficiency under the adsorption conditions of and the desorption conditions of 1.2 V/7 min desorption -1 V/1 min, respectively.