• ETRI Journal
• /
• v.38 no.2
• /
• pp.252-259
• /
• 2016

Di(1-aminopyrene)quinone (DAQ) as a quinone-containing conducting additive is synthesized from a solution reaction of 1-aminopyrene and hydroquinone. To utilize the conductive property of DAQ and its compatibility with activated carbon, a composite electrode for a supercapacitor is also prepared by blending activated carbon and DAQ (3:1 w/w), and its supercapacitive properties are characterized based on the cyclic voltammetry and galvanostatic charge/discharge. As a result, the composite electrode adopting DAQ exhibits superior electrochemical properties, such as a higher specific capacitance of up to $160F{\cdot}g^{-1}$ at $100mV{\cdot}s^{-1}$, an excellent high-rate capability of up to $1,000mV{\cdot}s^{-1}$, and a higher cycling stability with a capacitance retention ratio of 82% for the 1,000th cycle.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.2 no.5
• /
• pp.1-10
• /
• 1994

By applying of total electric capacitance method on engine connecting rod bearing during engine operating, the influence of engine operating conditions and lubricants on bearing oil film thickness was investigated. Minimum oil film thickness increases with kinematic viscosity, but as increasing of viscosity, the increasing ratio of film thickness is reduced. Also minimum oil film thickness increases with engine speed but there is a limit. Above this limit, film thickness decreases in opposition because of crankshaft inertia. As increasing of engine torque and oil temperature, munimum oil film thickness decreases linearly. For non-Newtonian oils, the correlation between $100{\circ}C$ kinematic viscosity and munimum oil film thickness is very poor.

• Proceedings of the Safety Management and Science Conference
• /
• 2003.11a
• /
• pp.351-357
• /
• 2003

The optimum polymer gel electrolyte composition ratio was 23 : 66 : 11 wt% of P(VdF-co-HFP) : PVP =20 : 3), (PC: EC =44 : 22) and TEABF$_4$. And the optimal thickness of polymer gel electrolyte was 50 ${\mu}{\textrm}{m}$. The electrochemical characteristics result of unit cell were 31.41 Fig of specific capacitance, and 3.21$\times$10$^{-3}$ S/cm of ion conductivity. Ion conductivity of polymer gel electrolytes decreased according to added PVP through impedance analysis, and it was higher in 7 wt%, but electrochemical characteristics of unit cell were better in 3 wt% PVP. And for excellent ion conductivity of polymer gel electrolytes, the use of a thin layer electrolyte(20 $\mu\textrm{m}$) was an effective method, but with unit cell application, the best thickness was 50 $\mu\textrm{m}$. Unit cell showed higher capacitance and more stable electrochemical performance when hot pressed between polymer gel electrolyte and electrode. This results from enhancement of the physical contact between the electrode and the polymer gel electrolyte and good accessibility of the liquid electrolyte to the electrode surface.

• Journal of Electrical Engineering and Technology
• /
• v.7 no.3
• /
• pp.358-365
• /
• 2012

A new third harmonic injection circuit for light-emitting diode (LED) drivers is proposed to eliminate electrolytic capacitors and thereby extend the lifetime of LED drivers. When a third harmonic current is injected to the input current of the LED driver, the required capacitance of the driver can be reduced. The proposed circuit can control an injection ratio and has simple circuitry. The synchronous third harmonic is generated by a phase locked loop (PLL), a 1/3 counter, and op-amps and applied to a power factor correction circuit. Thus, the storage capacitor can install film capacitors instead of the electrolytic capacitor. The value of storage capacitance can be reduced to 78% compared to an input power factor of 100%. The proposed circuit is applied to the 80W prototype LED driver to experimentally verify the performances.

• Proceedings of the IEEK Conference
• /
• 2000.07b
• /
• pp.587-590
• /
• 2000

For high-accuracy signal processing of differential capacitance transducers, an interface circuitry based on a switched-capacitor sample/hold circuit is developed. Driven by nonoverlapping two-phase clocks, the interface produces the output voltage which is proportional to the ratio of difference-to-sum of two capacitors of a differential transducer. Performances of a prototype chip fabricated using 0.6 $\mu\textrm{m}$ n-well CMOS process were measured and compared with those simulated by HSPICE. The measured results indicate that 0.1% resolution is achievable with the proposed interface and the temperature-dependence of the interface is small enough fur practical applications.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.5 no.2
• /
• pp.197-204
• /
• 1997

In order to investigate the relationship between the ring gap ratio and oil consumption, the axial motion of piston ring was measured by capacitance technique. The pressures of each land and the motions of each ring were calculated by orifice-volume method in which it is assumed that the ring gaps are the only gas leakage paths. The calculated results were compared with the measured ones. Consequently, it is known that the increase of ring gap ratio has the effect of lifting the first ring. The calculated results were roughly in accordance with those measured. Therefore, it is possible to predict the effect of design variables on the pattern of ring motion. It is known that the lift off of first ring accompanied by the increase of ring gap ratio make rise of oil consumption.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.43 no.10 s.352
• /
• pp.1-9
• /
• 2006

In this paper, a couple of 10Gb/s transimpedance amplifiers are realized in a 0.18um standard CMOS technology for optical communication applications. First, the voltage-mode inverter TIA(I-TIA) exploits inverter input configuration to achieve larger effective gm, thus reducing the input impedance and increasing the bandwidth. I-TIA demonstrates $56dB{\Omega}$ transimpedance gain, 14GHz bandwidth for 0.25pF photodiode capacitance, and -16.5dBm optical sensitivity for 0.5A/W responsivity, 9dB extinction ration and $10^{-12}$ BER. However, both its inherent parasitic capacitance and the package parasitics deteriorate the bandwidth significantly, thus mandating very judicious circuit design. Meanwhile, the current-mode RGC TIA incorporates the regulated cascade input configuration, and thus isolates the large input parasitic capacitance from the bandwidth determination more effectively than the voltage-mode TIA. Also, the parasitic components give much less impact on its bandwidth. RGC TIA provides $60dB{\Omega}$ transimpedance gain, 10GHz bandwidth for 0.25pF photodiode capacitance, and -15.7dBm optical sensitivity for 0.5A/W responsivity, 9dB extinction ration and $10^{-12}$ BER. Main drawback is the power dissipation which is 4.5 times larger than the I-TIA.

• Journal of the Semiconductor & Display Technology
• /
• v.8 no.2
• /
• pp.11-14
• /
• 2009

The $Sr_{0.7}Bi_{2.3}Nb_2O_9$(SBN) thin films are deposited on Pt-coated electrode(Pt/Ti/$SiO_2$/Si) using RF sputtering method at various $Ar/O_2$ ratio. We investigated the effect of deposition condition(specially $Ar/O_2$ ratio) on the structural properties of SBN thin film. As $Ar/O_2$ ratio was increased, the peaks in the XRD pattern became more sharp. Also, the peaks(008)(115)(220) in 80/20 of $Ar/O_2$ ratio were suddenly appeared. The optimum of the rougness showed about 4.33 nm in 70/30 of $Ar/O_2$ ratio. The crystallinity of SBN thin films were increased with the increase of $Ar/O_2$ ratio. Also, Deposition rate of SBN thin films was about 4.17 nm/min in 70/30 of $Ar/O_2$ ratio. The capacitance of SBN thin films were increased with the increase of $Ar/O_2$ ratio.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.54 no.6
• /
• pp.274-278
• /
• 2005

Voltage transformer(VT) comparison measurement system is usually used for measurements of ratio error and phase angle error of VT made in industry. Both ratio error and phase angle error in VT are critically influenced by values of burden of VT used. External burden effects on both ratio error and phase angle error in VT are theoretically calculated. From the theoretical calculation, a method of evaluation for linearity of ratio error and phase angle error in VT measurement system have been developed using the standard capacitive burdens, with negligible dissipation factor less than 10$^{-4}$. These burden consists of five standard capacitors, with nominal capacitance of 1.1 $\mu$F, 1 $\mu$F, 0.1 $\mu$F, 0.01 $\mu$F, 0.001 $\mu$F. The developed method has been applied in VT measurement system of industry, showing in good consistency and linearity within 0.001 $\%$ between theoretical and measured values.

• Electrical & Electronic Materials
• /
• v.9 no.2
• /
• pp.138-145
• /
• 1996

A multilayer piezoelectric transformer (MPT) which generates a high voltage dc power with low driving voltage and high voltage setup ratio was made by the tape casting method. The measured electrical characteristics of the MPT agreed with the results simulated from the equivalent circuit of the MPT. With increasing the number of layer in the MPT, the resonance curve of the input cur-rent revealed an asymmetry due to the increasing input capacitance, while that of output dc voltages revealed symmetry. The MPT which has very thin layer was excellently characterized as low driving voltage and high voltage setup ratio. The output dc voltage is nonlinearly influenced by the number of layer in the MPT.