• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• 제29권8호
• /
• pp.461-465
• /
• 2016

n-type silicon shows the better tolerance towards metal impurities with a higher minority carrier lifetime compared to p-type silicon substrate. Due to better lifetime stability as compared to p-type during illumination made the photovoltaic community to switch toward n-type wafers for high efficiency silicon solar cells. We fabricated the front electrode of the n-type solar cell with AgAl paste. The electrodes characteristics of the AgAl paste depend on the contact junction depth that is closely related to the firing temperature. Metal contact depth with p+ emitter, with optimized depth is important as it influence the resistance. In this study, we optimize the firing condition for the effective formation of the metal depth by varying the firing condition. The firing was carried out at temperatures below $670^{\circ}C$ with low contact depth and high contact resistance. It was noted that the contact resistance was reduced with the increase of firing temperature. The contact resistance of $5.99m{\Omega}cm^2$ was shown for the optimum firing temperature of $865^{\circ}C$. Over $900^{\circ}C$, contact junction is bonded to the Si through the emitter, resulting the contact resistance to shunt. we obtained photovoltaic parameter such as fill factor of 76.68%, short-circuit current of $40.2mA/cm^2$, open-circuit voltage of 620 mV and convert efficiency of 19.11%.

• Current Photovoltaic Research
• /
• 제2권4호
• /
• pp.173-176
• /
• 2014

We have investigated the seed layer formation of front side contact using the inkjet printing process. Conductive silver ink was printed on textured Si wafers with 80 nm thick $SiN_x$ anti reflection coating (ARC) layers and thickened by light induced plating (LIP). The inkjet printable sliver inks were specifically formulated for inkjet printing on these substrates. Also, a novel method to prepare nano-sized glass frits by the sol-gel process with particle sizes around 5 nm is presented. Furthermore, dispersion stability of the formulated ink was measured using a Turbiscan. By implementing these glass frits, it was found that a continuous and uniform seed layer with a line width of $40{\mu}m$ could be formed by a inkjet printing process. We also investigated the contact resistance between the front contact and emitter using the transfer length model (TLM). On an emitter with the sheet resistance of $60{\Omega}/sq$, a specific contact resistance (${\rho}_c$) below $10m{\Omega}{\cdot}cm^2$ could be achieved at a peak firing temperature around $700^{\circ}C$. In addition, the correlation between the contact resistance and interface microstructures were studied using scanning electron microscopy (SEM). We found that the added glass particles act as a very effective fire through agent, and Ag crystallites are formed along the interface glass layer.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2009년도 추계학술대회 논문집
• /
• pp.381-381
• /
• 2009

염료감응형 태양전지의 효율 향상을 위한 다양한 방법들 중 $TiO_2$ 나노 파우더의 표면 개질 및 페이스트의 분산성 향상을 위한 연구가 활발하게 진행되고 있다. 기존 나노 파우더의 표면 개질법으로는 액상 공정인 졸겔법이 있으나 표면 처리 공정에서의 응집현상은 아직 해결해야 할 과제 중 하나이다. 이에 본 연구에서는 진공증착방법인 ALD법을 이용하여 염료감응형 태양전지용 $TiO_2$ 나노 파우더의 $SiO_2$ 산화물 표면처리를 통한 분산특성을 파악하였다. 기존 ALD법의 경우 reactor의 온도가 $300{\sim}500^{\circ}C$ 정도의 고온에서 공정이 이루어졌지만 본 실험에서는 2차 아민계촉매(pyridine)을 사용하여 reactor의 온도를 $30^{\circ}C$정도의 저온공정에서 $SiO_2$ 산화물을 코팅을 하였다. MO source로는 액체상태의 TEOS$(Si(OC_2H_5)_4)$를, 반응가스로는 $H_2O$를 사용하였고, 불활성 기체인 Ar 가스는 purge 가스로 각각 사용 하였다. ALD 공정에 의해 표면처리 된 $TiO_2$ 나노 파우더의 분산특성은 각 공정 cycle에 따라 FESEM을 통하여 입자의 형상 및 분산성을 확인하였으며 입도 분석기를 통하여 부피의 변화 및 분산 특성을 확인하였다. 공정 cycle 이 증가함에 따라 입자간의 응집현상이 개선되는 것을 확인 할 수 있었으며, 100cycles에서 응집현상이 가장 많이 감소하는 것을 확인할 수 있었다. 또한 표면 처리된 $SiO_2$ 산화막은 XRD를 통한 결정 분석 및 EDX를 통한 정성 분석을 통하여 확인하였다.

• Journal of the Microelectronics and Packaging Society
• /
• 제18권1호
• /
• pp.23-27
• /
• 2011

Fabrication of porous silicon(PS) double layer by electrochemical etching is the first step in process of ultrathin solar cell using PS layer transfer process. The porosity of the porous silicon layer can be controlled by regulating the formation parameters such as current density and HF concentration. PS layer is fabricated by electrochemical etching in a chemical mixture of HF and ethanol. For electrochemical etching, highly boron doped (100) oriented monocrystalline Si substrates was used. Ths resistivity of silicon is $0.01-0.02\;{\Omega}{\cdot}cm$. The solution composition for electrochemical etching was HF (40%) : $C_2H_5OH$(99 %) : $H_2O$ = 1 : 1 : 2 (by volume). In order to fabricate porous silicon double layer, current density was switched. By switching current density from low to high level, a high-porosity layer was fabricated beneath a low-porosity layer. Etching time affects only the depth of porous silicon layer.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2010년도 춘계학술대회 초록집
• /
• pp.93.1-93.1
• /
• 2010

반사방지막은 태양전지 표면에서의 광 반사를 낮춰주며, Si wafer 표면에서의 carrier의 재결합을 줄이는 passivation 역할을 한다. 이를 위한 다양한 물질이 반사방지막으로 사용된다. 단일박막은 passivation 효과가 미미하여 최근 passivation 향상에 도움이 되는 이중구조 반사방지막이 널리 연구되어지고 있다. 하지만 물질이 다양해짐에 따라 공정시간 및 비용이 늘어나고, passivation에 최적화된 물질사용이 필수적으로 요구되는 단점이 있다. 따라서 본 연구에서는 기존에 passivation 효과가 뛰어나다고 알려진 SiNx의 굴절률 가변을 통하여 이중구조를 갖는 박막을 반사방지막으로 이용하여 그 특성을 비교, 분석하였다. SiNx 이중반사방지막은 0.8 Torr~1 Torr의 압력에서 $450^{\circ}C$의 기판온도로 PECVD를 이용하여 증착되었으며 이때의 plasma power는 180mW/$cm^2$으로 고정 하였다. 굴절률 1.9 및 2.3을 갖는 가스 조성비를 이용하여 각 layer의 두께를 20/60nm, 30/50nm, 40/40nm로 가변하였다. 샘플 제작 후 Sun-Voc 측정을 통하여 implied Voc 및 효율을 측정하였다. 단일반사방지막을 사용한 샘플의 경우 608mV의 implied Voc가 측정되었으며, FF는 82.8%, 효율은 17.6%로 측정되었다. 가장 우수한 특성을 나타낸 20/60nm의 두께로 증착된 샘플의 경우 implied Voc는 625mV, FF는 84.1%, 효율은 18.3%로 우수한 결과를 나타내었다. 반사도 측정 결과 단일반사방지막은 2.27%로 높았으나 SiNx 이중구조를 이용한 반사방지막은 1.67%로 낮은 값을 확인 하여 이중구조의 반사방지막이 반사도 저감 및 passivation 효과 향상에 도움이 되는 것을 확인할 수 있었다.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• 제27권2호
• /
• pp.85-90
• /
• 2014

Ag paste has been used in the front electrode of the Si-solar cell. It is composed by Ag powder, glass frit, binder, solvent and dispersant. The role of the binder and the solvent is to make a flow and a printing property. However, it was not enough to report the printing properties with the variation of binder in the controled viscosity. In this study, we selected 3 kinds of typical binder which were used as binder for the paste in the industry, such as Ethyl cellulose, Hydroxypropyl cellulose and Acrylic. Ag pastes using these were prepared, controled viscosity and printed on the SiNx coated Si wafer. In the 'A paste' used Acrylic binder, printed hight was highest and 'H paste' used Hydroxypropyl cellulose binder was lowest. Because 'H paste' was high viscosity due to the molecular weight, the solvent was added in the paste to control the viscosity. Therefore, the content of solid was lower in 'H paste'. The relative pattern width which is related to the spreading of paste was the best in the case of 'H paste' and 'EH paste' at $30^{\circ}C$. It is thought that the optimization of the relative pattern width is possible for a paste by the controling shear thinning phenomenon. In the case of 'A paste', though printing hight was best, the pattern width was dependant on the temperature.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2009년도 춘계학술대회 논문집
• /
• pp.49-52
• /
• 2009

Practical building integrated photovoltaic system built by Kolon E&C has been monitored and evaluated with respect to power generation, which was installed in Deokpyeong Eco Service Area in Deokpyeong, Gyeonggi, Korea. The amorphous silicon transparent PV module in this BIPV system has 44Wp in power output per unit module and 10% of transmittance with the unit dimension with $980mm{\times}950mm$. The BIPV system was applied as the skylight in the main entrance of the building. This study provided the database for the practical application of the transparent thin-film PV module for BIPV system through 11 month monitoring as well as various statistical analyses such as monthly power output and insolation. Average monthly power output of the system was 52.9kWh/kWp/month which is a 60% of power output of the previously reported data obtained under $30^{\circ}$of an inclined PV module facing south(azimuth=0). This lower power output can be explained by the installation condition of the building facing east, west and south, which was resulted from the influence of azimuth.

• Proceedings of the Korean Vacuum Society Conference
• /
• 한국진공학회 2013년도 제45회 하계 정기학술대회 초록집
• /
• pp.231-231
• /
• 2013

ZnO은 hexagonal wurtzite 구조를 갖는 직접 천이형 화합물 반도체로서, 상온에서 3.37 eV 정도의 wide band gap energy를 가지고 있으며, 60 meV의 큰 엑시톤 결합 에너지(exciton binding energy)를 갖는다. 또한 동종 기판이 존재하고 열, 화학적으로 안정한 상태이며 습식 식각이 가능한 장점으로 인해 각광받고 있다. 또한, ZnO 박막은 우수한 전기 전도성을 나타내며 광학적 투명도가 우수하기 때문에 투명전극으로 많이 이용되어 왔고, 태양 전지(solar cell), 가스 센서, 압전소자 등 많은 분야에서 사용되고 있다. 이와 같은 ZnO박막을 안정적인 쇼트키 다이오드 특성을 얻기 위해서는 쇼트키 배리어 장벽의 형성이 필수적이다. Mg을 ZnO에 첨가하여 MgZnO 박막을 형성할 경우, 금속의 일함수와 MgZnO의 전자친화력 차이가 증가하여 더 큰 쇼트키 장벽 형성이 가능하며, 금속의 일함수가 큰 물질을 사용해야 한다. 또한, 박막의 결함이 적은 박막을 형성해야 하는 에피탁셜 박막이 필요하다. SiC는 높은 포화 전자 드리프트 속도(${\sim}2.7{\times}107$ cm/s), 높은 절연 파괴전압(~3 MV/cm)과 높은 열전도율(~5.0W/cm) 특징을 가지고 있으며, MgZnO/Al2O3의 격자 불일치는 ~19%인 반면에 MgZnO/SiC의 격자 불일치는 ~6%를 가진다. 금속의 일함수가 큰 Ag 금속은 열처리가 될 경우 AgOx가 될 경우 더욱 안정적인 쇼트키 장벽을 형성될 수 있을 것으로 판단된다. 본 연구에서는 쇼트키 접합을 형성하기 위해 금속의 일함수가 큰 Ag 금속을 사용하였으며, Al2O3 기판과 6H-SiC 기판위에 MgZnO(30 at.%) 박막을 증착하였다. 증착 후에 Ag를 증착 한 뒤 급속 열처리를 하였다. 열처리된 MgZnO의 경우 열처리 하지않은 소자보다 약 $10^5$ 이상의 우수한 on/off 특성을 보였다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 한국진공학회 2014년도 제46회 동계 정기학술대회 초록집
• /
• pp.462-462
• /
• 2014

The effect of rear passivation for passivated emitter and rear cell (PERC) using ozone and H2O oxidant of atomic layer deposited (ALD) Al2O3 was studied by post-annealing in N2 and forming gas ambients. Rear surface of PERC solar cell was passivated by Al2O3 grown by ALD with ozone and H2O oxidant. Al2O3 grown by ALD with ozone oxidant has been known to have many advantages, such as lower interface defects, low leakage current density. Its passivation quality is better than Al2O3 with H2O. Al2O3 layer with 10 nm and 20 nm thickness was grown at $150^{\circ}C$ with ozone oxidant and at $250^{\circ}C$ with H2O oxidant. And then each samples were post-annealled at $450^{\circ}C$ in N2 ambients and at $850^{\circ}C$ in forming gas ambients. The passivation quality was investigated by measuring the minority carrier lifetime respectively. We examined atomic layer deposited Al2O3 such as growth rate, film density, thickness, negative fixed charge density at AlOx/Si interface, and reflectance. The influences of process temperature and heat treatment were investigated using Sinton (WCT-120) by Quasi-Steady State Photoconductance (QSSPC) mode. Ozone-based ALD Al2O3 film shows the best carrier lifetime at lower deposition temperature than H2O-based ALD.

• Korean Journal of Materials Research
• /
• 제20권11호
• /
• pp.606-610
• /
• 2010

Films consisting of a silicon quantum dot superlattice were fabricated by alternating deposition of silicon rich silicon nitride and $Si_3N_4$ layers using an rf magnetron co-sputtering system. In order to use the silicon quantum dot super lattice structure for third generation multi junction solar cell applications, it is important to control the dot size. Moreover, silicon quantum dots have to be in a regularly spaced array in the dielectric matrix material for in order to allow for effective carrier transport. In this study, therefore, we fabricated silicon quantum dot superlattice films under various conditions and investigated crystallization behavior of the silicon quantum dot super lattice structure. Fourier transform infrared spectroscopy (FTIR) spectra showed an increased intensity of the $840\;cm^{-1}$ peak with increasing annealing temperature due to the increase in the number of Si-N bonds. A more conspicuous characteristic of this process is the increased intensity of the $1100\;cm^{-1}$ peak. This peak was attributed to annealing induced reordering in the films that led to increased Si-$N_4$ bonding. X-ray photoelectron spectroscopy (XPS) analysis showed that peak position was shifted to higher bonding energy as silicon 2p bonding energy changed. This transition is related to the formation of silicon quantum dots. Transmission electron microscopy (TEM) and electron spin resonance (ESR) analysis also confirmed the formation of silicon quantum dots. This study revealed that post annealing at $1100^{\circ}C$ for at least one hour is necessary to precipitate the silicon quantum dots in the $SiN_x$ matrix.