• Smart Structures and Systems
• /
• v.29 no.5
• /
• pp.661-675
• /
• 2022

In this paper, an electric vehicle drives with efficient control and low cost hardware using four quadrant DC converter with Permanent Magnet Direct Current (PMDC) motor fed by DC boost converter is presented. The main idea of this work is to improve the energy efficiency of the conversion chain of an electric vehicle by inserting a boost converter between the battery and the four quadrant-DC motor chopper assembly. Consequently, this method makes it possible to maintain the amplification gain of the 4 quadrant chopper constant regardless of the battery voltage drop and even in the presence of a fault in the battery. One of the most important control problems is control under heavy uncertainty conditions. The higher order sliding mode control technique is introduced for the adjustment of DC bus voltage and mechanical motor speed. To implement the proposed approach in the automotive field, experimental tests were carried out. The performances obtained show the usefulness of this system for a better energy management of an electric vehicle and an ideal control under different operating conditions and constraints, mostly at nominal operation, in the presence of a load torque, when reversing the direction of rotation of the motor speed and even in case of battery chamber failure. The whole system has been tested experimentally and its performance has been analyzed.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.28 no.6D
• /
• pp.801-807
• /
• 2008

This study attempts to evaluate and compare the land consumption efficiencies of various urban transport modes, utilizing the time-area method. With the careful considerations of travel conditions and modal characteristics, equations for the computation of time-area for various different modes are derived. With the appropriate assumed values of parameters, time-area consumptions per person per km for each mode both for peak and off-peak situations are computed and evaluated. The relationships between the time-area consumed and operating speed for each mode are graphically demonstrated and discussed. An example of the time-area consumed for a hypothetical commuter round-trip using various modes are also presented in order to clearly show the consumption of parking requirements by specific modes. It shows that regardless of facilities used, auto users are by far the worst in terms of area efficiency and that transit, especially rail rapid transit, is a superior mode. Pedestrian and bicycle, though consuming more than expected, also demonstrate the advantage in case of a short-distance trip in terms of area efficiency compared with the bus transit modes.

• Journal of Space Technology and Applications
• /
• v.3 no.4
• /
• pp.355-372
• /
• 2023

As the need for low-cost, high-efficiency cubesats develops in the new space age, commercial paradigms are shifting in the private sector. This paper examines the challenges of launching and operating both domestic and foreign cubesats, and proposes practical solutions to ensure the robustness and reliability of the satellites from a practical perspective. In particular, the paper deals with checkpoints that are easy to miss, focusing on key events that can occur from the satellite deployment process through normal mode to mission mode in the operation scenario. Although the contents presented in this paper may not be technically applicable to all cubesat systems due to the different nature of each satellite bus system, they will be of some help during satellite assembly, integration and testing.

• Journal of Astronomy and Space Sciences
• /
• v.19 no.1
• /
• pp.67-74
• /
• 2002

Optical observations of Geostationary and Molynia orbit spin-stabilized satellites over the Korean peninsula have been carried out at the Kyung Hee University Observatory with a 30 inch telescope. We have observed 5 spin-stabilized satellites, and obtained 0spin periods, which can be used for deducing a design for each bus model. Verifications of spin periods of 3 known satellites from manufacturer, and observations of 2 unknown satellites were made. The difference between known spin periods and observed spin periods is 0.06sec on the average and the difference of those spin rates is 3.3rpm on the average. Those results indicate that spin periods and spin rates of observed geostationary spin-stabilized satellites are within operating limits. Spin rates of unknown satellites, Fengyun 2B and Molynia 1-87 are 89.3rpm, 78.4rpm earh. It is suggested that the research of spin stabilized satellites can be used for the determinations of standard light sources for short period celestial objects and helpful for the constructions of satellite databases with photometric and/or spectroscopic satellite observations.

• Journal of Korean Society of Transportation
• /
• v.22 no.7 s.78
• /
• pp.41-48
• /
• 2004

We may consider the inducement of demand to public transportation as a solution to relieve traffic congestion and pollution. Subway has merits as moving on schedule, transporting more people than bus. But subway is required a vast investment in the early stage of construction has a huge debt. So it runs into red figures, and on this account, services of subway are falling more and more. Development of subway's operation cost function is useful to understand structure of subway's operation and catch the relations of operation cost and actual results. In addition, we can present the policy that is a helpful to the operation as development of operation cost function. But there are short of studies about operation cost deal with a subway comparison with local train. Because local train has many lines and data, on the other hand, subway has one to four lines and less data. Most of previous studies sought the operation cost function of Seoul. So this study aimed to develop and apply the operation cost function of Seoul, Incheon, Busan and Daegu area using full allocation method. In this study, we considered the number of passengers, track-km, train-km, revenue as actual results. By appling the operation cost function, we compared the average cost of each city and confirmed the existence of economies of scale about the number of passengers, train-km.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.43 no.6 s.348
• /
• pp.9-17
• /
• 2006

We proposed a new High-speed CMOS Level Up/Down Shifter circuits that can be used with Dynamic Voltage and Frequency Scaling(DVFS) algorithm, for low power system in the SoC(System-on-Chip). This circuit used to interface between the other voltage levels in each CMOS circuit boundary, or between multiple core voltage levels in a system bus. Proposed circuit have advantage that decrease speed attenuation and duty ratio distortion problems for interface. The level up/down shifter of the proposed circuit designed that operated from multi core voltages$(0.6\sim1.6V)$ to used voltage level for each IP at the 500MHz input frequency The proposed circuit supports level up shifting from the input voltage levels, that are standard I/O voltages 1.8V, 2.5V, 3.3V, to multiple core voltage levels in between of $0.6V\sim1.6V$, that are used internally in the system. And level down shifter reverse operated at 1Ghz input frequency for same condition. Simulations results are shown to verify the proposed function by Hspice simulation, with $0.6V\sim1.6V$ CMOS Process, $0.13{\mu}m$ IBM CMOS Process and $0.65{\mu}m$ CMOS model parameters. Moreover, it is researched delay time, power dissipation and duty ration distortion of the output voltage witch is proportional to the operating frequency for the proposed circuit.

• KIPS Transactions on Computer and Communication Systems
• /
• v.10 no.7
• /
• pp.199-204
• /
• 2021

Digital substation refers to a substation that digitizes functions and communication methods of power facilities such as monitoring, measuring, control, protection, and operation based on IEC 61850, an international standard for the purpose of intelligent power grids. Based on the intelligent operating system, efficient monitoring and control of power facilities is possible, and automatic recovery function and remote control are possible in the event of an accident, enabling rapid power failure recovery. With the development of digital technology and the expansion of the introduction of eco-friendly renewable energy and electric vehicles, the spread of direct current distribution systems is expected to expand. MVDC is a system that utilizes direct current lines with voltage levels and transmission capacities between HVDCs applied to conventional transmission systems and LVDCs from consumers. Converting existing lines in substations, where most power equipment is alternating current centric, to direct current lines will reduce transmission losses and ensure greater current capacity. The process bus of a digital substation is a communication network consisting of communication equipment such as Ethernet switches that connect installed devices between bay level and process level. For MVDC linkage to existing digital substations, the process level was divided into two buses: AC and DC, and a system that can be comprehensively managed in conjunction with diagnostic IEDs as well as surveillance and control was proposed.

• Journal of the Korean Institute of Gas
• /
• v.26 no.6
• /
• pp.9-15
• /
• 2022

In order to verify the durability of the high-pressure hydrogen tank in the operating pressure range, a hydraulic rupture test should be performed. However, if the bubbles generated by the initial injection process of water are attached to the inner wall of the tank and remain, a sudden pressure change of the bubbles during the rupture of the pressurized tank may cause shock and noise. Therefore, in this study, the flow velocity required to remove the bubbles remaining on the inner wall of the tank was predicted through simplified formulas, and the shape of the injection nozzle to maintain the flow velocity was determined based on the shape of the hydrogen tank for the hydrogen bus. In addition, a numerical model was developed to predict the change in flow velocity according to the inlet pressure, and an experiment was performed through a model tank to prove the validity of the prediction result. As a result of the experiment, the flow velocity near the tank wall was similar to the predicted value of the analysis model, and when the inlet pressure was 1.5 to 5.5 bar, the minimum size of the removable bubble was predicted to be about 2.2 to 4.6 mm.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.33 no.2
• /
• pp.171-187
• /
• 2023

Objectives: Aircraft cabin cleaning work is characterized by being performed within a limited time in a narrow and enclosed space. The objective of this study was to evaluate the exposure levels to dust, ultra fine dust(PM2.5) and black carbon(BC) among aircraft cabin cleaners. Methods: Active personal air sampling for respirable dust(n=73) and BC(n=47) was conducted during quick transit cleaning(cabin general and vacuum-specific) and seat cover replacement and total dust and PM2.5 were area-air-sampled as well. Also, size distribution of particle was identified with the cleaning workers targeted. Dusts were collected with PVC filters using gravimetric analysis. The concentration of PM2.5 and the particle size distribution were measured with real-time direct reading portable equipment using light scattering analysis. The concentration of BC was measured by aethalometer(filter-based real-time light absorption analysis instrument). Results: The geometric mean of respirable dust was the highest at vacuum cleaning as 74.4 ㎍/m³, following by replacing seat covers as 49.3 ㎍/m³ and cabin general cleaning as 47.8 ㎍/m³ . The arithmetic mean of PM2.5 was 4.83 ~ 9.89 ㎍/m³ inside the cabin, and 28.5~44.5 ㎍/m³ outside the cabin(from bus and outdoor waiting space). From size distribution, PM_2.5/PM₁₀ ratio was 0.54 at quick transit cleaning and 0.41 at replacing seat covers. The average concentration of BC was 2~7 ㎍/m³, showing a high correlation with the PM2.5 concentration. Conclusions: The hazards concentration levels of aircraft cabin cleaners were very similar to those of roadside outdoor workers. As the main source of pollution is estimated to be diesel vehicles operating at airports, and it is necessary to replace older vehicles, strengthen pollutant emission control regulations, and introduce electric vehicles. In addition, it is necessary to provide as part of airport-inftastructure a stable standby waiting space for aircraft cabin cleaners and introduce a systematic safety and health management system for all workers in the aviation industry.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.44 no.4
• /
• pp.531-544
• /
• 2024

The purpose of this study is to analyze traffic flow characteristics according to the market penetration rate (MPR) of autonomous vehicles (AV) on road sections where bus rapid transit (BRT) is actually operating. Furthermore, the maximum traffic volume was set through estimation of future traffic demand, and traffic flow characteristics were analyzed through traffic simulation for each scenario considering of a combination of BRT introduction and AV's MPR. To test statistical significance, Kruskal-Willis test and Jonckheere-Terpstra test were used to examine the impact of the market penetration rate of Autonomous vehicles on travel time and delay time etc. At the same time, the existence of the order relationship among travel time data according to the market penetration rate of autonomous vehicle was examined. As a result of the analysis, it was founded that the travel time significantly decreased as the MPR of AV increases in both intermittent flow and continuous flow environments. In particular, in the case of continuous flow, the law of increasing returns was satisfied in the effect of increasing travel speed and reducing travel time as the MPR of AV increases. The results of this study are expected to be used as a basic information for design plans for road reconstruction and space utilization after the commercialization of AV in the future.