• Wind and Structures
• /
• v.34 no.1
• /
• pp.115-125
• /
• 2022

The high-Reynolds number flow around a rectangular cylinder, having streamwise to crossflow length ratio equal to 5 is analyzed in the present paper. The flow is characterized by shear-layer separation from the upstream edges. Vortical structures of different size form from the roll-up of these shear layers, move downstream and interact with the classical vortex shedding further downstream in the wake. The corresponding mean flow is characterized by a recirculation region along the lateral surface of the cylinder, ending by mean flow reattachment close to the trailing edge. The mean flow features on the cylinder side have been shown to be highly sensitive to set-up parameters both in numerical simulations and in experiments. The results of 21 Large Eddy Simulations (LES) are analyzed herein to highlight the impact of the lateral mean recirculation characteristics on the near-wake flow features and on some bulk quantities. The considered simulations have been carried out at Reynolds number Re=DU_∞/ν=40 000, being D the crossflow dimension, U_∞ the freestream velocity and ν the kinematic viscosity of air; the flow is set to have zero angle of attack. Some simulations are carried out with sharp edges (Mariotti et al. 2017), others with different values of the rounding of the upstream edges (Rocchio et al. 2020) and an additional LES is carried out to match the value of the roundness of the upstream edges in the experiments in Pasqualetto et al. (2022). The dimensions of the mean recirculation zone vary considerably in these simulations, allowing us to single out meaningful trends. The streamwise length of the lateral mean recirculation and the streamwise distance from the upstream edge of its center are the parameters controlling the considered quantities. The wake width increases linearly with these parameters, while the vortex-shedding non-dimensional frequency shows a linear decrease. The drag coefficient also linearly decreases with increasing the recirculation length and this is due to a reduction of the suctions on the base. However, the overall variation of C_D is small. Finally, a significant, and once again linear, increase of the fluctuations of the lift coefficient is found for increasing the mean recirculation streamwise length.

• Macromolecular Research
• /
• v.9 no.4
• /
• pp.228-237
• /
• 2001

The evolution of conformational constraints in bisphenol-A polycarbonate (BAPC) upon quiescent bulk crystallization was quantitatively analyzed from calorimetric study employing a rigid amorphous fraction (RAF) as an indicator of the level of conformational constraints. From the correlation between corrected crystallinity (X$\sub$c/) and total rigid fraction (f$\sub$r/), it was found that, regardless of molar mass distribution and thermal treatment conditions, semicrystalline BAPC always exhibits greater f$\sub$r/ than X$\sub$c/ maintaining a quantitative relationship of f$\sub$r/〓2X$\sub$c/ in the range of 0.0 $\sub$c/< 0.4. This directly indicates the evolution of approximately the same amount of RAF as X$\sub$c/, (i.e., RAF〓X$\sub$c/) upon bulk crystallization of BAPC. It was also found that T$\sub$g/ per se and T$\sub$g/ broadening enhance as RAF increases, and there appears to be a critical level of RAF (>0.2) needed to initiate significant changes in both quantities.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.7 no.1
• /
• pp.20-29
• /
• 1995

A theoretical model for film condensation of a vapor including a relatively lighter noncondensable gas on a horizontal tube has been formulated on the basis of the conservation laws and other fundamental physical principles. The model is applied to the prediction of the condensation heat transfer characteristics for the Freon vapor in the presence of air on a horizontal tube. Calculated results for the mean heat transfer coefficient, which is shown to depend strongly on the bulk concentration of air, are in good agreement with the available experimental results for a range of operating conditions. The distributions of physical quantities along the surface of tube are also calculated, such as the boundary layer thickness and local heat transfer coefficient. The present model is readily reduced to the Nusselt model as the bulk concentration of air decreases to zero. Therefore, the transition from the condensation of pure vapor to that of vapor-air mixture occurs continuously not abruptly.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.42
• /
• pp.85-91
• /
• 2000

Dwindling supplies and increasing costs of conventional highway materials used in road construction as well as concerns over shrinking landfill spaces prompt researchers to investigate the use of waste products, such as fly ash, as substitute materials in highway construction. The highway industry is capable of utilizing waste materials in large quantities if their effect on pavement performance proves to be technically, economically and environmentally satisfactory. This research examines the effects of fly ash when used as partial replacement of aggregate in asphaltic concrete mixtures. And measuring the effect of fly ash on bulk specific gravity, air void, indirect tensile strength (ITS) under dry and wet conditioning as well as the tensile strength ratio (TSR) of asphaltic concrete mixture. The results indicated that asphaltic concrete mixtures containing 2% and 5% fly ash produced about the same TSR value as control mixture. And all of the mixtures met the minimum ITS and TSR requirements established by the South Carolina Department of Transportation (SC DOT) for Type 1A surface courses. At this point and with this limited study, these asphaltic concrete mixtures is recommended in several applications such as parking lot, secondary roads and driveways.

• Journal of computational fluids engineering
• /
• v.16 no.2
• /
• pp.49-55
• /
• 2011

Turbulent flows with wavy wall are simulated using Residual-based Variational Multiscale Method (RB-VMS) which is proposed by Bazilves et al(2007) as new Large Eddy Simulation methodology. Incompressible Navier-Stokes equations are integrated using Isogeometric analysis which adopt the basis function as NURBS. The Reynolds number is 6760 based on the bulk velocity and averaged channel height. And the amplitude (${\alpha}/{\lambda}$) of wavy wall is 0.05. The computational domain is $2{\lambda}{\times}1.05{\lambda}{\times}{\lambda}$ in the streamwise, wall normal and spanwise direction. Mean quantities and turbulent statistics near wavy wall are compared with DNS results of Cherukat et al.(1998). The predicted results show good agreement with reference data.

• Journal of computational fluids engineering
• /
• v.13 no.3
• /
• pp.28-34
• /
• 2008

In engineering application of large eddy simulation, there are still questions as follows grid dependency on numerical results, the effect of upwind scheme against a calculation instability, appropriate boundary conditions dealing with turbulence fluctuation and the performance of SGS models. In this study, in order to develop the LES to the engineering application, large eddy simulation was carried out to investigate the effect of upwind scheme, turbulent subgrid model and the grid dependancy of the flow around a wall-mounted cube in a channel at Re=40,000 based on cubic height and bulk mean velocity. The computed velocities, turbulence quantities, separation and reattachment length were evaluated compared with the experimental results of R. Matinuzzi and C. Tropea.

• Nuclear Engineering and Technology
• /
• v.38 no.8
• /
• pp.763-778
• /
• 2006

Injection of microbubbles within the turbulent boundary layer has been investigated for several years as a method to achieve drag reduction. However, the physical mechanism of this phenomenon is not yet fully understood. Experiments in a channel flow for single phase (water) and two phase (water and microbubbles) flows with various void fraction values are studied for a Reynolds number of 5128 based on the half height of the channel and bulk velocity. The state-of-the art Particle Tracking Velocimetry (PTV) measurement technique is used to measure the instantaneous full-field velocity components. Comparisons between turbulent statistical quantities with various values of local void fraction are presented to elucidate the influence of the microbubbles presence within the boundary layer. A decrease in the Reynolds stress distribution and turbulence production is obtained with the increase of microbubble concentration. The results obtained indicate a decorrelation of the streamwise and normal fluctuating velocities when microbubbles are injected within the boundary layer.

• Coupled systems mechanics
• /
• v.11 no.5
• /
• pp.411-438
• /
• 2022

In this paper, we present the parameter identification for inelastic and multi-scale problems. First, the theoretical background of several fundamental methods used in the upscaling process is reviewed. Several key definitions including random field, Bayesian theorem, Polynomial chaos expansion (PCE), and Gauss-Markov-Kalman filter are briefly summarized. An illustrative example is given to assimilate fracture energy in a simple inelastic problem with linear hardening and softening phases. Second, the parameter identification using the Gauss-Markov-Kalman filter is employed for a multi-scale problem to identify bulk and shear moduli and other material properties in a macro-scale with the data from a micro-scale as quantities of interest (QoI). The problem can also be viewed as upscaling homogenization.

• Journal of Digital Convergence
• /
• v.16 no.3
• /
• pp.275-289
• /
• 2018

It is necessary to develop a bridgehead port for trading with northern countries to promote trade through the East Sea because the East Sea Rim economic bloc around the Northeast Asia including South Korea, China, Russia, Japan, and North Korea has a high growth potential in the future. Therefore, this study aims to suggest a strategic direction to enhance the competitiveness of Donghae Port through reinforcement of container cargoes by conducting Importance-Performance Analysis (IPA) for stakeholders of Donghae Port. The analysis results suggest that it is necessary to improve the five evaluation factors: attractiveness of container and bulk volumes, appropriate ratio of export/import container quantities, frequency of vessel entry and diversity of sea routes, convenience of complex linked transportation, and competitiveness of cargo handling equipment. The implications of this study are as follows. First, it is necessary to continuously research the current status of container and bulk cargo volumes of the port and ways to increase the absolute cargo volume. Second, we need to consider realistic alternatives to improve the ratio of export/import container quantities. Third, in terms of network, we should establish a service improvement plan to increase the frequency of port calls and the diversity of sea routes. Furthermore, incentives should be provided to increase the trade volume of Donghae Port through strengthened complex linked transportation function. Finally, it is urgently necessary to provide investment support for container handling equipment as an essential requirement for the activation of the container cargoes in Donghae Port.

• Journal of Korea Port Economic Association
• /
• v.35 no.3
• /
• pp.93-108
• /
• 2019

This study aims to suggest a containerization plan for non-standardized cargo; it also reveals the significance of containerization in facilitating freight inducement and cargo creation for increasing the competitiveness of the Gwangyang port container terminal and checking excessive competition among terminal operators. Therefore, this study suggested a containerization plan and its significance by dividing 14 items, ones with low containerization ratios or undergoing containerization, bulk, and liquid cargoes. In the case of general cargo, it will be necessary to raise the utilization rate by remodeling a general container or improving cargo loading techniques. In the case of bulk cargo, it will be necessary to exploit the benefits of containerization in preventing product deterioration due to rain, facilitating the sale of small orders, ensuring clean cargo handling, and reducing logistics cost, among others. In the case of liquid cargo, it will be necessary to order and sell liquid cargo in small quantities by using superior quality, safe, and durable Flexitank or Flexibag products, which offer transportation convenience and reduce time and costs.