• 펄프종이기술
• /
• 제47권3호
• /
• pp.18-23
• /
• 2015

In this study, the effects of cationic fatty acid bulky promotor on the properties of BCTMP (bleached chemithermomechnical pulp) handsheet including bulk and strength were elucidated. As results, it was observed that the bulk of BCTMP handsheet increased with the increases of the concentration of cationic fatty acid bulky agent, while mechanical properties such as tensile strength and burst strength decreased. The opacity of BCTMP handsheet also increased with the increases of the concentration of cationic fatty acid bulky agent, while brightness was almost not changed. The effectiveness of bulky agent with SwBCTMP (softwood) was higher than that with HwBCTMP (hardwood). Compared with previous research on the effect of bulky agent on BKP handsheet, the bulk increase of BCTMP handsheet was greater compared to that of BKP handsheet. However, the reduction of mechanical property in BCTMP handsheet was lower than that of BKP handsheet.

• 펄프종이기술
• /
• 제43권3호
• /
• pp.21-29
• /
• 2011

Recently, the use of recycled fibers was increased in order to replace the virgin pulp for low production cost and forest conservation. However, the recycled fibers decreases drainage rate, papermaking efficiency and product quality by short fibers and low wettability because of hornification. To overcome the limitation of low drainage rate, the technology of organic fillers were applied. Wooden fillers gave high bulk and stiffness of paper, but they reduced the strength of paper. In order to improve strength properties 4 types of strength additives were added and analyzed. Cationic starch, branched strength additive, linear wet strength additive, and linear dry strength additive were used. The drainage rate and paper properties such as bulk, air permeability and tensile strength were measured. As results of analysis, addition of branch type of strength agent such as C-starch was effective than linear type of strength agent in the drainage rate. Nevertheless there was no effect on the drainage rate by adding the pretreated wooden fillers. By adding the pretreated wooden fillers, bulk, air permeability and tensile strength of handsheets were improved with low dosage than non-pretreated fillers.

• 한국자기학회:학술대회 개요집
• /
• 한국자기학회 2013년도 임시총회 및 하계학술연구발표회
• /
• pp.18-18
• /
• 2013

A FeRh alloy is a well-known efficient magnetocaloric material and some experimental and theoretical studies of bulk FeRh have been reported already by several groups. In this study we report first-principles calculations on magnetic properties of different thickness FeRh thin films in order to investigate the possibility to enhance further the magnetocaloric efficiency. We used Vienna Ab-initio Simulation Package (VASP) code. We found that the FeRh thin films have quite different magnetic properties from the bulk when the thickness is thinner than 6-atomic-layers. While bulk FeRh has a G-type antiferromagnetic (AFM) state, thin films which are thinner than 6-atomic-layers have an A-type AFM state or a ferromagnetic(FM) state. We will discuss possibility of magnetic phase transitions of the FeRh thin films in the view point of a magnetocaloric effect. And we found 4-, 5-, 6-layers films with Fe surface and 7-layers film with Rh surface are FM and they have dozens eV magnetocrystalline anisotropy (MCA) energy. MCA energy leads to determine energy barrier when magnetic states are changed by external magnetic field.

• 한국주조공학회지
• /
• 제28권6호
• /
• pp.261-267
• /
• 2008

In-situ quasicrystalline icosahedral (I) phase reinforced Ti-based bulk metallic glass (BMG) matrix composites have been successfully fabricated by using two distinct thermal histories for BMG forming alloy. The BMG composite containing micron-scale Iphase has been introduced by controlling cooling rate during solidification, whereas nano-scale I-phase reinforced BMG composite has been produced by partial crystallization of BMG. For mechanical properties, micron-scale I-phase distributed BMG composite exhibited lower strength and plasticity compared to the monolithic BMG. On the other hand, nano-scale icosahedral phase embedded BMG composite showed enhanced strength and plasticity. These improved mechanical properties were attributed to the multiplication of shear bands and blocking of the shear band propagation in terms of isolation and homogeneous distribution of nanosize icosahdral phases in the glassy matrix, followed by stabilizing the mechanical and deformation instabilities.

• EDISON SW 활용 경진대회 논문집
• /
• 제2회(2013년)
• /
• pp.294-298
• /
• 2013

A FeRh alloy is a well-known efficient magnetocaloric material and some experimental and theoretical studies of bulk FeRh have been reported already by several groups. In this study we report first-principles calculations on magnetic properties of different thickness FeRh thin films in order to investigate the possibility to enhance further the magnetocaloric efficiency. We used two methods of a Vienna Ab-initio Simulation Package (VASP) code and SIESTA package. We found that the FeRh thin films have quite different magnetic properties from the bulk when the thickness is thinner than 6-atomic-layers. While bulk FeRh has a G-type antiferromagnetic(AFM) state, thin films which are thinner than 6-atomic-layers have an A-type AFM state or a ferromagnetic (FM) state. We will discuss possibility of magnetic phase transitions of the FeRh thin films in the view point of a magnetocaloric effect. And we found 4-, 5-, 6-layers films with Fe surface and 7-layers film with Rh surface are FM and they have relatively small magnetocrystalline anisotropy (MCA) energy about less than 70 meV. The small MCA energy leads to reduction of the strength of magnetic field in operating a magnetic refrigerator.

• 한국분말재료학회지
• /
• 제7권3호
• /
• pp.143-148
• /
• 2000

NiAl alloy powders were prepared by mechanical alloying method and bulk specimens were produced using hot isostatic pressing techniques. This study focused on the transformation behavior and properties of Ni-Al mechanically alloyed powders and bulk alloys. Transformation behavior was investigated by differential scanning calorimeter (DSC), XRD and TEM. Particle size distribution and microstructures of mechanically alloyed powders were studied by particle size analyzer and scanning electron microscope (SEM). After 10 hours milling, XRB peak broadening appeared at the alloyed powders with compositions of Ni-36at%Al to 40at%Al. The NiAl and $Ni_3Al$ intermetallic compounds were formed after water quenching of solution treated powders and bulk samples at $1200^{\circ}C$, but the martensite phase was observed after liquid nitrogen quenching of solution treated powders. However, the formation of $Ni_3Al$ intermetallic compounds were not restricted by fast quenching into liquid nitrogen. It is considered to be caused by fast diffusion of atoms for the formation of stable $\beta$(NiAl) phase and $Ni_3Al$ due to nano sized grains during quenching. Amounts of martensite phase increased as the composition of aluminium component decreased in the Ni-Al alloy, which resulted in the increasing damping properties.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2000년도 하계학술대회 논문집
• /
• pp.387-390
• /
• 2000

The $Al_2$O$_3$specimens were prepared by the conventional mixed oxide method with addition La$_2$O$_3$, Bi$_2$O$_3$. The specimens were sintered at 15$25^{\circ}C$, 5hr., in air. The structural properties of the specimens were investigated by XRD and SEM. The $Al_2$O$_3$ceramics with dopants had hexagonal structure and didn't show secondary phases. In the case of specimens with 0.25wt% La$_2$O$_3$and 0.25wt% Bi$_2$O$_3$bulk densities and lattice parameter of c/a were 3.818g/cm$^3$, 3.783g/cm$^3$and ca=2.725, c/a=2.723, respectively. The bulk densities of $Al_2$O$_3$ceramics were decreased with dopants.

• 한국재료학회지
• /
• 제31권2호
• /
• pp.101-107
• /
• 2021

Pores produced by carbonization in bulk graphite process degrade the mechanical and electrical properties of bulk graphite. Therefore, the pores of bulk graphite must be reduced and an impregnation process needs to be performed for this reason. In this study, bulk graphite is impregnated by varying the viscosity of the impregnant. The pore volume and pore size distribution, according to the viscosity of the impregnant, are analyzed using a porosimeter. The total pore volume of bulk graphite is analyzed from the cumulative amount of mercury penetrated. The volume for a specific pore size is interpreted as the amount of mercury penetrating into that pore size. This decreases the cumulative amount of mercury penetrating into the recarbonized bulk graphite after impregnation because the viscosity of the impregnant is lower. The cumulative amount of mercury penetrating into bulk graphite before impregnation and after three times of impregnation with 5.1cP are 0.144 mL/g and 0.125 mL/gm, respectively. Therefore, it is confirmed that the impregnant filled the pores of the bulk graphite well. In this study, the impregnant with 5.1 cP, which is the lowest viscosity, shows the best effect for reducing the total pore volume. In addition, it is confirmed by Raman analysis that the impregnant is filled inside the pores. It is confirmed that phenolic resin, the impregnant, exists inside the pores through micro-Raman analysis from the inside of the pore to the outside.

• 펄프종이기술
• /
• 제48권1호
• /
• pp.111-118
• /
• 2016

The effects of pulp beating degree and bulky promotor concentration on the properties of handsheet including a bulk and strength have been investigated during manufacturing of low density paper (high bulk paper) with cationic fatty acid bulky promotor. It was found that paper bulk increased with increasing cationic fatty acid bulky agent concentration, while tensile strength decreased. On the other hand the opacity of handseets also increased with increasing cationic fatty acid bulky agent concentration, while brightness decreased slightly. With increasing pulp beating degree, paper bulk as well as tensile strength increased, while opacity decreased. Brightness did not show a significant difference with increasing pulp beating degree. The highest bulk and strength values were observed when 1.5% (SwBKP) and 2% (HwBKP) of bulky promotor was treated into the 450 mL CSF pulp slurry.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 추계학술대회
• /
• pp.1145-1150
• /
• 2003

Zr-based bulk metallic glasses have a significant mechanical properties such as high strength and elastic strain limit, and a good processing ability due to the deformation behavior such as superplasticity under supercooled liquid region. Recently, many researches on the determination of optimum working condition in various bulk metallic glasses have been carried out. In this study, the deformation behavior and forming conditions of $Zr_{55}Cu_{30}Al_{10}Ni_{5}$ bulk metallic glass were investigated under three different strain rates and at various temperatures between 627K and 727K. The glass transition temperature, crystallization temperature and supercooled liquid region of $Zr_{55}Cu_{30}Al_{10}Ni_{5}$ bulk metallic glass are 680K, 762K and 82K, respectively.