• Journal of the Korean Geotechnical Society
• /
• v.18 no.5
• /
• pp.237-249
• /
• 2002

Nonlinearity and anisotropy of soil should be considered for the exact prediction of deformation before the failure state. In this study, a new constitutive model is developed in which the nonlinearity of soil is formulated by Ramberg-Osgood equation and the soil anisotropy is implemented by the cross-anisotropic elasticity. Nonlinear anisotropic model and other models for comparison are used to analyze the simple boundary value problems and the circular footing problem. In the results, the anisotropic ratio of elastic modulus is a key value for the bulk modulus of soil, the coeffcient of earth pressure at rest, and the slope of effective stress paths. Furthermore, it is found that the nonlinearity of soil considering the in-situ stresses has the great influence on the magnitude of settlements.

• Korean Journal of Materials Research
• /
• v.32 no.4
• /
• pp.181-185
• /
• 2022

In this study, phase-pure titanium dioxide TiO₂ ceramics are sintered using standard high-temperature solid-state reaction technique at different temperatures (1,000, 1,100, 1,200, 1,300, 1,400 ℃). The effect of sintering temperature on the densification and impedance properties of TiO₂ ceramics is investigated. The bulk density and average grain size increase with the increase of sintering temperature. Impedance spectroscopy analysis (complex impedance Z^* and complex modulus M^*), performed in a broad frequency range from 100 Hz to 10 MHz, indicates that the TiO₂ ceramics are dielectrically heterogeneous, consisting of grains and grain boundaries. The complex impedance Z^* -plane indicates the resistance of grains of the TiO₂ ceramics increases with increasing sintering temperature, while that of grain boundaries develops in the opposing direction. The complex modulus M^*-plane shows a grain capacitance that seems to be independent of the sintering temperature, while that of the grain boundaries decreases with increasing sintering temperature. These results suggest that different sintering temperatures have effects on the microstructure, leading to changes in the impedance properties of TiO₂ ceramics.

• Korean Journal of Materials Research
• /
• v.31 no.12
• /
• pp.682-689
• /
• 2021

NbC, HfC, TaC, and their solid solution ceramics have been identified as the best materials for ultrahigh-temperature ceramics. However, their structural stability and elastic properties are mostly unclear. Thus, we investigated structure and elastic properties of (Nb_1-xTa_x)C and (Nb_1-xHf_x)C solid solutions via ab initio calculations. Our calculated results show that the stability of (Nb_1-xTa_x)C and (Nb_1-xHf_x)C increases with the increase of Hf and Ta content, and (Nb_1-xHf_x)C is more stable than (Nb_1-xTa_x)C at the same content of Hf and Ta. The lattice constants decrease with increasing of Hf and Ta content. (Nb_1-xTa_x)C and (Nb_1-xHf_x)C carbides are mechanically stable and brittle. Bulk modulus of (Nb_1-xTa_x)C increases with increasing Ta content. In contrast, bulk modulus of (Nb_1-xHf_x)C decreases with increasing Hf content. Hardness of solid solutions shows the highest values at the (Nb_0.25Ta_0.75)C and (Nb_0.75Hf_0.25)C. In particular, (Nb_0.75Hf_0.25)C shows the highest hardness for the current system. The results indicate that the overall mechanical properties of (Nb_1-xHf_x)C solid solutions are superior to those of (Nb_1-xTa_x)C solid solutions. Therefore, controlling the Hf and Ta element and content of the (Nb_1-xTa_x)C and (Nb_1-xHf_x)C Solid solution is crucial for optimizing the material properties.

• Journal of Magnetics
• /
• v.14 no.4
• /
• pp.137-143
• /
• 2009

The convergence behavior of the all-electron full-potential linearized augmented plane-wave (FLAPW) method with the explicit orthogonalization (XO) scheme is tested on ferromagnetic bulk body-centered-cubic Fe. Applying a commonly used criterion relating the plane-wave and angular momentum cutoffs, $l_{max}\;=\;R_{MT}K_{max}$, where $R_{MT}$ is the muffin-tin (MT) sphere radius and $K_{max}$ is the plane-wave cutoff for the basis - the total energy is converged and stable for $K_{max}R_{MT}$ = 10. The total energy convergence dependence on the star-function cutoff, $G_{max}$, is minimal and so a $G_{max}$ of 3$K_{max}$ or a large enough $G_{max}$ is a reasonable choice. We demonstrate that the convergence with respect to $l_{max}$ or a fixed large enough $G_{max}\;and\;K_{max}$ are independent, and that $K_{max}$ provides a better measure of the convergence than $R_{MT}K_{max}$. The dependence of the total energy on $R_{MT}$ is shown to be small if the core states are treated equivalently, and that the XO scheme is able to treat systems with significantly smaller $R_{MT}$ than the standard LAPW method. For converged systems, the calculated lattice parameter, bulk modulus, and magnetic moments are in excellent agreement with the experimental values.

• Journal of the Mineralogical Society of Korea
• /
• v.19 no.3 s.49
• /
• pp.189-195
• /
• 2006

Compression work on a pyrite powder has been carried out using energy dispersive X-ray diffraction (EDXRD) with Mao-Bell type diamond anvil cell (DAC) and synchrotron radiation(SR) at room temperature. It has been reported the bulk moduli of pyrite show the large variations depending on the experimental conditions as well as the apparatus used. Thus, two kinds of sample in different pressure transmitting media of both NaCl and MgO powder emerged in alcoholic fluids were subjected to measure their compressibilities. Bulk moduli thus obtained are 138.9 GPa and 198.2 GPa, respectively, and this result contradicts to the anticipated values according to the hydrostaticity conditions of the sample chamber. This might be due to the alcoholic fluids phase transition mainly with the side effects from the difference of both solid state detector (SSD) used and E*d value applied. All experiments were performed at the Beam Line 1B2 of Pohang Light Source (PLS).

• Journal of the Korean Applied Science and Technology
• /
• v.33 no.4
• /
• pp.771-776
• /
• 2016

The acrylate copolymer having good thermal stability, coating and adhesion properties was designed and prepared. We prepared copolymers in >95% high yield using methyl methacrylate, isobornyl methacrylate and 2-hydroxyethyl methacrylate monomers by the bulk and emulsion polymerization techniques. The $^1H$-NMR spectrum was used to identify chemical structure and glass transition temperatures increased from $123^{\circ}C$ to $140^{\circ}C$ confirmed by DSC, DMA and TGA analysis. In addition, as the content of IBMA increased, storage modulus and thermal decomposition temperature increased. As the content of IBMA increased from 10% to 30% in the composition for the entire monomer, tensile strength increased from 22 to 30 MPa in both polymers prepared by bulk and emulsion techniques. The contact angle increased from 70 to up to 88 degrees due to hydrophobic property of IBMA.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.20 no.3
• /
• pp.882-890
• /
• 1996

Mechanical properties, including Young's modulus, residual stress and rupture strength, of a thermally evaporated gold film have been measured form a blister test. In a theoretical study, the priniple of minimum potential energy and that of virtual work have been applied to the pressurized circular membrane problem, and load-deflection relations have been derived for typical membrane deflection mode of spheroidal shape. In an experimental study, circular gold membranes of 4800 A-thickness and 3.5mm diameter were fabricated by the silicon electropolishing technique. Mecahnical properties of the thin gold films were deduced from the load-deflection curves obtained by the blister test, Young's moduli, obtianed from blister test, have been in the range of 45-70 GPa, while those of bulk gold have been in the range of 78-80 GPa. Residual stresses in the evaporated gold films have been measured as 28-110MPa in tension, The rupture strength of the gold film has turned out to be almost equal to that of dental gold alloy (310-380MPa). It has been demonstrated that the present specimen fabrication method and blister test apparatus have been effective for simultaneous measurement of Young's modulus, residual stress and repture strength of thin solid films. Especially, the electropolishing technique employed here has provided a simple and practical way to fabricate thin membranes in a circular or an arbitrary shape, which could not be obtained by the conventional anisotropic silicon mecromachining technique.

• Journal of Powder Materials
• /
• v.20 no.5
• /
• pp.350-354
• /
• 2013

In this study, porous titanium samples were manufactured by space holder methods using two kinds of urea and sodium chloride space holders. Three-dimensional pore structures were obtained by a computed-tomography (CT) technique and utilized for finite element analysis in order to investigate the mechanical properties. The CT-based finite element analyses were in better agreement with the experimental results than unit cell model-based analyses. Both the experimental and CT-based results showed the same tendency that the elastic modulus decreased with increasing the porosities. The total porosity of the bulk body plays a key role in determining the elastic modulus of porous materials.

• The Journal of Advanced Prosthodontics
• /
• v.8 no.6
• /
• pp.479-488
• /
• 2016

PURPOSE. The aim of this study was to test the modulus of elasticity (E) across the interfaces of yttria stabilized zirconia (YTZP) / veneer multilayers using nanoindentation. MATERIALS AND METHODS. YTZP core material (KaVo-Everest, Germany) specimens were either coated with a liner (IPS e.max ZirLiner, Ivoclar-Vivadent) (Type-1) or left as-sintered (Type-2) and subsequently veneered with a pressable glass-ceramic (IPS e.max ZirPress, Ivoclar-Vivadent). A $5{\mu}m$ (nominal tip diameter) spherical indenter was used with a UMIS CSIRO 2000 (ASI, Canberra, Australia) nanoindenter system to test E across the exposed and polished interfaces of both specimen types. The multiple point load - partial unload method was used for E determination. All materials used were characterized using Scanning Electron Microscopy (SEM) and X - ray powder diffraction (XRD). E mappings of the areas tested were produced from the nanoindentation data. RESULTS. A significantly (P<.05) lower E value between Type-1 and Type-2 specimens at a distance of $40{\mu}m$ in the veneer material was associated with the liner. XRD and SEM characterization of the zirconia sample showed a fine grained bulk tetragonal phase. IPS e-max ZirPress and IPS e-max ZirLiner materials were characterized as amorphous. CONCLUSION. The liner between the YTZP core and the heat pressed veneer may act as a weak link in this dental multilayer due to its significantly (P<.05) lower E. The present study has shown nanoindentation using spherical indentation and the multiple point load - partial unload method to be reliable predictors of E and useful evaluation tools for layered dental ceramic interfaces.

• Journal of the Korean Society for Railway
• /
• v.17 no.6
• /
• pp.415-422
• /
• 2014

Reinforced trackbeds are an important layer that has a significant effect on the deformation of the track, therefore, a deeper understanding of reinforced trackbeds is necessary. In this paper, we conduct a large triaxial test in order to evaluate the resilient modulus ($M_R$) of reinforced trackbed materials through considering several factors such as the grain size distribution (GSD) and loading conditions. It is identified that the maximum size of the particle, GSD, and compacted water content affect the $M_R$ but the loading frequency does not. Because these tests are performed with consideration of the field environment, the test results are useful for analyzing tracks including reinforced trackbeds. The data are limited to evaluating the parameters of $M_R$ model; however the parameters of the deviatoric and bulk stress models that can be used in various loading conditions are proposed.