• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2001년도 가을 학술발표회 논문집
• /
• pp.1097-1102
• /
• 2001

Seismic safety of continuous span concrete bridge can be enhanced by distributing a large seismic lateral load to each supporting pier. A new viscoelastic device called Shock Transmission Unit(STU), which is a simple cylinder-piston assembly packed with a so-called silicone putty compound, enables the lateral seismic load to be transmitted to the pier by installation of the device to movable bearings of the bridge. The seismic safety of concrete bridges having the STU depends on not only safety of the bridges globally but also safety of anchor systems which anchors the STU to concrete pier. An experimental investigation is performed to study the behavior of cast-in-place anchor and post-installed anchor subjected to shear load statically and cyclically according to different edge distance, embedment length, and anchor spacing. Finally, the experimental results are compared with results by design methods of ACI and CCD, and results by FEM analysis.

• 국제초고층학회논문집
• /
• 제11권3호
• /
• pp.197-205
• /
• 2022

One of important design challenges in Chongqing Raffles City Plaza project is Sky Bridge structural design and its connection scheme in high level. This article systematically describes the structural system and its design and analysis methodology, with discussing the impacts on structural performance due to different connection approaches. The seismic isolation scheme in high level is innovatively adopted to the final design. Under the conditions of various load cases, the different models and assumptions are implemented. A full assessment on Sky Bridge's structural performance, seismic isolation, and its connection is conducted in terms of seismic performance based design. By co-operating with architecture, MEP and other disciplines, the structural economy index is fulfilled.

• 대한전자공학회논문지
• /
• 제15권3호
• /
• pp.30-34
• /
• 1978

병렬 공진회로를 부하로 하는 브리지 인버어터를 해석하였다. 본 논문에서는 실제 회로설계에 필요한 트리거주파수의 한계, SCR 턴-오프 시간의 제한 범위 및 콘덴서의 최대 전압과 트리거속도에 따른 부하전류값을 구하였다.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2007년도 추계학술대회 논문집
• /
• pp.395-400
• /
• 2007

LRT(Light Railway Train), which is a intermediate system of train and bus, is arose for the solution of subway construction cost and the transportation capacity of bus. LRT was introduced in 1980's. About 30 local governments are plan to introduce LRT or constructing LRT, at present. AGT(Automated Guide-way Transit) system, which is a kind of LRT, is operated without driver. Rubber wheeled AGT system can reduce the noise and vibration compare to steel wheeled AGT, so it is estimated as ideal transportation system for urban area. And live loads at bridge are classified as the static load of vehicle and the dynamic wheel contact load which is occurred from the interaction of bridge and vehicle vibration, and the surface roughness. In the case of AGT system, the dynamic increment factor of bridge is greater than the normal train bridge and roadway bridge, because, the weight of AGT vehicle is more light that the train of truck. The exact method for dynamic increment factor is experiment. But this method is needed much money and time, moreover, this method cannot be adopted in design. Therefore, a simulation program for the interaction of AGT bridge, vehicle and surface roughness was developed, in this study. And the program was verified by experiment. As a result, the accuracy of the simulation program can be verified.

• 한국기계가공학회지
• /
• 제20권2호
• /
• pp.32-37
• /
• 2021

To realize a zero-energy building, a technology that minimizes the energy loss due to thermal bridges by preventing their formation is emerging as an important design factor. In this study, we develop a thermal bridge breaker to prevent thermal bridging in a metal panel roof and attempt to analyze the effects of its application. To this end, we fabricated a thermal bridge breaker and analyzed it in terms of its strength and heat-transfer characteristics, in addition to conducting a load simulation. The thermal bridge prevention effect of the developed thermal bridge breaker improved the insulation performance of the metal panel roof, and the results of a cooling/heating peak load simulation performed by applying the heat transmission resistance test results to a building proved the existence of this effect.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1998년도 봄 학술발표회논문집(II)
• /
• pp.439-446
• /
• 1998

Earthquake damage civil engineering structures every year in the world and bridges are no exception. Bridge structures have proven to be vulnerable to earthquake, sustaining damage to substructure and foundation and being totally destroys as superstructures collapse from their supporting elements. The poor seismic performance of bridge structures is surprising in view of the substantial advance made in design and construction for vertical load. Recently, bridge spans have been pushed further than before, alignment has become increasingly complex and aesthetic requirement have been become more demanding. To reduce the seismic force and to improve the safety of the advanced bridges, the bridge bearings which are the substructures and foundations and their connections to the superstructure become more important and critical elements. Therefore, the functions about seismic devices to be using as bridge bearing are discussed.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2009년도 세계 도시지반공학 심포지엄
• /
• pp.133-144
• /
• 2009

Incheon Bridge, 18.4 km long sea-crossing bridge, will be opened to the traffic in October 2009 and this will be the new landmark of the gearing up north-east Asia as well as the largest & longest bridge of Korea. Incheon Bridge is the integrated set of several special featured bridges including a magnificent cable-stayed girder bridge which has a main span of 800 m width to cross the navigation channel in and out of the Port of Incheon. Incheon Bridge is making an epoch of long-span bridge designs thanks to the fully application of the AASHTO LRFD (load & resistance factor design) to both the superstructures and the substructures. A state-of-the-art of the geotechnologies which were applied to the Incheon Bridge construction project is introduced. The most Large-diameter drilled shafts were penetrated into the bedrock to support the colossal superstructures. The bearing capacity and deformational characteristics of the foundations were verified through the world's largest static pile load test. 8 full-scale pilot piles were tested in both offshore site and onshore area prior to the commencement of constructions. Compressible load beyond 30,000 tonf pressed a single 3 m diameter foundation pile by means of bi-directional loading method including the Osterberg cell techniques. Detailed site investigation to characterize the subsurface properties had been carried out. Geotextile tubes, tied sheet pile walls, and trestles were utilized to overcome the very large tidal difference between ebb and flow at the foreshore site. 44 circular-cell type dolphins surround the piers near the navigation channel to protect the bridge against the collision with aberrant vessels. Each dolphin structure consists of the flat sheet piled wall and infilled aggregates to absorb the collision impact. Geo-centrifugal tests were performed to evaluate the behavior of the dolphin in the seabed and to verify the numerical model for the design. Rip-rap embankments on the seabed are expected to prevent the scouring of the foundation. Prefabricated vertical drains, sand compaction piles, deep cement mixings, horizontal natural-fiber drains, and other subsidiary methods were used to improve the soft ground for the site of abutments, toll plazas, and access roads. Light-weight backfill using EPS blocks helps to reduce the earth pressure behind the abutment on the soft ground. Some kinds of reinforced earth like as MSE using geosynthetics were utilized for the ring wall of the abutment. Soil steel bridges made of corrugated steel plates and engineered backfills were constructed for the open-cut tunnel and the culvert. Diverse experiences of advanced designs and constructions from the Incheon Bridge project have been propagated by relevant engineers and it is strongly expected that significant achievements in geotechnical engineering through this project will contribute to the national development of the longspan bridge technologies remarkably.

• 한국강구조학회 논문집
• /
• 제24권6호
• /
• pp.613-625
• /
• 2012

철도교는 일반적으로 설계하중에 근접한 열차하중이 빈번하게 통과할 가능성이 있으므로, 초기설계단계부터 여러 구조상세에 대해 피로특성을 충분한 반영하는 것이 필요하다. 그럼에도 불구하고 철도교에 작용하는 축하중의 크기 및 배치 특성, 피로에 대한 부적절한 구조상세의 적용 등으로 인하여 강철도 플레이트거더교에서 부분적으로 피로균열이 보고되고 있다. 상부플랜지와 복부의 용접이음부에서의 피로균열의 주요 발생 원인의 하나는 침목을 지지하는 주거더와 열차하중이 작용되는 레일과의 중심간격 차이에 따른 열차하중의 편심작용에 의한 것이다. 이 연구에서는 공용중인 강철도 상로플레이트거더교를 대상으로 현장조사 및 현장계측, 일련의 구조해석을 실시하고, 대상교량의 구조거동 특성 및 피로균열의 발생 원인의 규명, 보수 보강(안)에 대하여 검토하였다.

• 콘크리트학회논문집
• /
• 제26권3호
• /
• pp.267-275
• /
• 2014

최근 곡선교 사용이 증가함에 따라 기존 곡선 교량의 한계점을 극복하고자 PSC 곡선 주형을 이용한 곡선교에 대한 해석적 연구가 활발히 진행되고 있다. 그러나 기존의 프레임 요소를 이용한 격자해석방법으로는 PSC 곡선교에 대한 정밀해석이 어렵다. 이에 따라 이 연구에서는 PSC 곡선교의 정밀 유한 요소 해석을 실시하여 프리캐스트 PSC 곡선교의 설계를 위한 참고자료로 사용하고자 한다. 이를 위하여 3차원 솔리드 요소를 사용한 모델링을 실시하고, 거더 수, 하중 재하 위치, 단면 변화, 긴장력 변화 및 편긴장력 도입 여부와 같은 매개변수에 대한 거동을 평가하였다. 해석 결과 경간장 50 m 3주형 교량의 항복하중과 파괴 하중이 경간장 40 m 2주형 교량에 비해 200% 이상의 성능을 보였고, 외측거더에 하중을 가하였을 경우 도심의 위치에 따라 하중저항력 및 거더 간의 처짐 편차가 낮게 평가되는 것으로 나타났다. 또한 거더 단면을 변화시킨 경우 단면의 증가에 따라 구조성능이 향상되는 것으로 나타났으나 PS도입량의 변화에 의한 효과에 비해 경제성과 시공성에서 불리한 것으로 나타났다. PS 도입량 변화에 따른 영향을 분석한 결과 PS 도입량이 증가함에 따라 솟음량과 하중저항력이 비례하여 증가하였으며 거더 간 처짐 편차가 줄어드는 경향을 보였다. 또한, 편긴장력을 도입하였을 시 도입량 증가에 비례하여 내외측 거더 모두에서 하중저항력이 증가하며, 특히 외측거더에 편긴장력이 도입되었을 때 더 우수한 성능을 보이는 것으로 나타나, PSC 곡선교의 경제성 및 안정성을 확보하는데 효율적인 것으로 나타났다.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2010년도 하계학술대회 논문집
• /
• pp.129-130
• /
• 2010

For the high power demand and N+1 redundancy, this paper presents the digital load share (LS) controller design and the implementation of paralleled phase-shifted full-bridge converters (PSFBC) used in distributed power systems. By adopting the digital control strategy, separately used ICs for PSFBC and LS control functions in analog systems can be merged into a cost-effective digital controller. To compensate and stabilize both PSFBC and LS loops with the direct digital design approaches, small-signal model of the system is derived in discrete-time domain. The steady-state and dynamic load sharing performances are also investigated. Experimental results from two 1.2 kW paralleled PSFBC modules are shown to verify the proposed work.