• 한국구조물진단유지관리공학회 논문집
• /
• 제13권1호통권53호
• /
• pp.179-185
• /
• 2009

최근 건설구조물에 대한 FRP의 활용에 관한 연구가 활발히 진행되고 있다. FRP는 단위중량당의 강도와 강성이 기존 건설재료인 강재나 콘크리트에 비해 매우 크고, 부식에 대한 저항성이 뛰어나는 등의 여러 가지 물리적, 화학적 장점이 있다. 이러한 장점을 이용하여 FRP 외양관을 단면의 효율성을 극대화할 수 있고 경제성과 경관에 매우 효과가 큰 스트럿을 가진 PSC 박스거더교의 스트럿 부재의 피복재로 적용하고자 한다. 본 논문에서는 스트럿을 가진 PSC 박스거더에 사용되는 FRP 외양관의 적용성을 평가하기 위하여 이와 관련한 FRP 외양관의 시편실험과 FRP로 피복된 콘크리트 부재의 압축실험을 수행하였으며, 실험결과로부터 콘크리트 강도와 에너지 흡수능력 및 연성이 증진되어 스트럿 부재로써 충분한 안전성을 확보할 수 있음을 확인하였다.

• 한국재난정보학회 논문집
• /
• 제8권1호
• /
• pp.36-46
• /
• 2012

작년 3월에 발생한 일본 대지진으로 인해 우리나라 역시 간접피해 등을 우려하며, 지진에 대한 피해를 최소화 할 수 있는 설계방법의 필요성과 기존 구조물의 내진 성능 향상에 대한 관심이 더욱 증가하고 있다. 사회기반시설물인 교량 등의 손상 붕괴는 사회적 경제적으로 미치는 파급효과가 커 이러한 구조물에 대한 내진성능의 평가가 상당히 중요하게 부각되고 있다. 내진성능에 대한 검토방법들은 많지만 결정론적 방법에 의한 것이 대다수로, 지진에 대한 구조물의 안전성 평가에는 손상단계에 따른 취약성 또는 손상도를 평가하는 방법이 필요하다. 본 논문에서는 납면진받침(LRB)과 탄성마찰포트받침(RFPB)을 사용한 PSC Box Girder 교량에 대하여 지진의 특성인 PGA, PGV, SA, SV, SI에 대한 손상도 곡선을 구하고, 두 지진 격리 장치의 성능을 비교 평가하였다.

• Steel and Composite Structures
• /
• 제37권2호
• /
• pp.117-136
• /
• 2020

Curved steel-concrete composite box girder has been widely adopted in urban overpasses and ramp bridges. In order to investigate its mechanical behavior under complicated and combined bending, shear and torsion load, two large-curvature composite box girders with interior angles of 25° and 45° were tested under static hogging moment. Based on the strain and deflection measurement on critical cross-sections during the static loading test, the failure mode, cracking behavior, load-displacement relationship, and strain distribution in the steel plate and rebar were investigated in detail. The test result showed the large-curvature composite box girders exhibited notable shear lag in the concrete slab and steel girder. Also, the constraint torsion and distortion effect caused the stress measured at the inner side of the composite beam to be notably higher than that of the outer side. The strain distribution in the steel web was approximately linear; therefore, the assumption that the plane section remains plane was approximately validated based on strain measurement at steel web. Furthermore, the full-process non-linear elaborate finite element (FE) models of the two specimens were developed based on commercial FE software MSC.MARC. The modeling scheme and constitutive model were illustrated in detail. Based on the comparison between the FE model and test results, the FE model effectively simulated the failure mode, the load-displacement curve, and the strain development of longitudinal rebar and steel girder with sufficient accuracy. The comparison between the FE model and the test result validated the accuracy of the developed FE model.

• Wind and Structures
• /
• 제28권5호
• /
• pp.285-298
• /
• 2019

For super long-span bridges, the aerodynamic forces induced by the flow passing the box girder should be considered carefully. And the Reynolds number sensitively of aerodynamic characteristics is one of considerable issue. In the study, a numerical study on the Reynolds number sensitivity of aerodynamic characteristic (flow pattern, pressure distribution and aerodynamic forces) of a twin-box girder were carried out using large eddy simulation (LES) with the dynamic Smagorinsky-Lilly subgrid model. The results show that the aerodynamic characteristics have strong correlation with the Reynolds number. At the leading edge, the flow experiences attachment, departure, and reattachment stages accompanying by the laminar transition into turbulence, causing pressure plateaus to form on the surface, and the pressure plateaus gradually shrinks. Around the gap, attributing that the flow experiences stages of laminar cavity flow, the wake with alternate shedding vortices, and turbulent cavity flow in sequence with an increase in the Reynolds number, the pressures around the gap vary greatly with the Reynold number. At the trailing edge, the pressure gradually recovers as the flow transits to turbulence (the flow undergoes wake instability, shear layer transition-reattachment station), In addition, at relative high Reynolds numbers, the drag force almost does not change, however, the lift force coefficient gradually decreases with an increase in Reynolds number.

• Smart Structures and Systems
• /
• 제29권1호
• /
• pp.29-39
• /
• 2022

Crack detection plays an important role in the maintenance and protection of steel box girder of bridges. However, since the cracks only occupy an extremely small region of the high-resolution images captured from actual conditions, the existing methods cannot deal with this kind of image effectively. To solve this problem, this paper proposed a novel three-stage method based on deep learning technology and morphology operations. The training set and test set used in this paper are composed of 360 images (4928 × 3264 pixels) in steel girder box. The first stage of the proposed model converted high-resolution images into sub-images by using patch-based method and located the region of cracks by CBAM ResNet-50 model. The Recall reaches 0.95 on the test set. The second stage of our method uses the Attention U-Net model to get the accurate geometric edges of cracks based on results in the first stage. The IoU of the segmentation model implemented in this stage attains 0.48. In the third stage of the model, we remove the wrong-predicted isolated points in the predicted results through dilate operation and outlier elimination algorithm. The IoU of test set ascends to 0.70 after this stage. Ablation experiments are conducted to optimize the parameters and further promote the accuracy of the proposed method. The result shows that: (1) the best patch size of sub-images is 1024 × 1024. (2) the CBAM ResNet-50 and the Attention U-Net achieved the best results in the first and the second stage, respectively. (3) Pre-training the model of the first two stages can improve the IoU by 2.9%. In general, our method is of great significance for crack detection.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 1997년도 가을 학술발표회 논문집
• /
• pp.95-102
• /
• 1997

Jointless bridge is a new construction method applicable to bridge of short length. In the jointless bridge expansion of superstructure due to thermal effect was absorbed in the flexible pile-type abutment in stead of expansion joint in the conventional bridges. By removing expansion joint, it retards deterioration and extends life time of bridge. In this paper, jointless bridge of steel box girder type was studied through finite element analysis. Stress variations of superstructure and pile due to thermal effect was studied for the two span continuous integral bridge of 80m length and the results of analysis was presented.

• Structural Engineering and Mechanics
• /
• 제72권4호
• /
• pp.503-512
• /
• 2019

The construction of segmental precast concrete bridge is an increase due to its superior performance and economic advantages. This type of bridge is appropriate for spans within 30 to 150 m (100 to 500 ft), known as mega-projects and the design optimization would lead to considerable economic benefits. A box-girder cross section superstructure of balanced cantilever construction method is assessed here. The depth of cross section, (variable along the span linearly), bottom flange thickness, and the count of strands are considered as design variables. The optimum design is characterized by geometry, serviceability, ductility, and ultimate limit states specified by AASHTO. Genetic algorithm (GA) is applied in two fronts: as to the saving in construction cost 8% and as to concrete volume 6%. The sensitivity analysis is run by considering different parameters like span/depth ratio, relation between superstructure cost, span length and concrete compressive strength.

• 한국지진공학회:학술대회논문집
• /
• 한국지진공학회 2000년도 추계 학술발표회 논문집 Proceedings of EESK Conference-Fall 2000
• /
• pp.341-347
• /
• 2000

Even for the same structure, the analysis results as well as design values might have differences depending on the selected analysis model. Therefore it is desirable to determin model considering the required accuracy of the analysis results, the given time restried economy. " Standard Specification for Roadway Bridges" Division V, Seismic Design prove "Single Mode Spectral Analysis Method" as the basic analysis method for the earthquake design of roadway bridges classified as "regular". In this study a 5 span steel box girl selected which satisfies the regularity and the applicability of the provided analysis simplified model in checked. For the comparision of the analysis results, "Multi-Mode Spect Method" is used with a detailed model.hod" is used with a detailed model.odel.

• Wind and Structures
• /
• 제6권4호
• /
• pp.263-278
• /
• 2003

This study investigates the effects of a bridge deck's width-to-depth (B/H) ratio and turbulence on buffeting response and flutter critical wind speed of long-span bridges by conducting section model tests. A streamlined box section and a plate girder section, each with four B/H ratios, were tested in smooth and turbulent flows. The results show that for the box girders, the response increases with the B/H ratio, especially in the vertical direction. For the plate girders, the vertical response also increases with the B/H ratio. However, the torsional response decreases as the B/H ratio increases. Increasing the B/H ratio and intensity of turbulence tends to improve the bridge's aerodynamic stability. Experimental results obtained from the section model tests agree reasonably with the calculated results obtained from a numerical analysis.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2003년도 가을 학술발표회 논문집
• /
• pp.444-451
• /
• 2003

In this study, a new three-dimensional finite element analysis model of high-speed railway bridges considering train-bridge interaction, in which various improved finite elements are used for modeling structural members, is proposed. The box-type bridge deck of a railway bridge is modeled by the NFS(Nonconforming Flat Shell) elements with 6 degrees of freedom. Track structures are idealized using the beam finite elements with the offset of beam nodes and those on Winkler foundation with two parameters. And, the vehicle model devised for a high-speed train is employed, which has an articulated bogie system. By Lagrange's equations of motion, the equations of motion of a bridge-train system can be formulated. Finally, by deriving the equations of the forces acting on a bridge considering bridge-train interaction the complete system matrices of total bridge-train system can be constructed. As numerical examples of this study, 2-span PC box-girder bridge is analyzed and results are compared with experimental results.