• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2014.10a
• /
• pp.565-568
• /
• 2014

This paper presents a 0.2V DC/DC boost converter with regulated output for thermoelectric energy harvesting. To use low voltages from a thermoelectric device, a start-up circuit consisting of native NMOS transistors and resistors boosts an internal VDD, and the boosted VDD is used to operate the internal control block. When the VDD reaches a predefined value, a detector circuit makes the start-up block turn off to minimize current consumption. The final boosted VSTO is achieved by alternately operating the sub-boost converter for VDD and the main boost converter for VSTO according to the comparator outputs. When the VSTO reaches 2.4V, a buck converter starts to operate to generate a stabilized output VOUT. Simulation results shows that the designed converter generates a regulated 1.8V output from an input voltage of 0.2V, and its maximum power efficiency is 60%. The chip designed using a $0.35{\mu}m$ CMOS process occupies $1.1mm{\times}1.0mm$ including pads.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2015.10a
• /
• pp.412-415
• /
• 2015

This paper presents a MPPT(Maximum Power Point Tracking) control CMOS interface circuit for vibration energy harvesting. The proposed circuit consists of an AC-DC converter, MPPT Controller, DC-DC boost converter and PMU(Power Management Unit). The AC-DC converter rectifies the AC signals from vibration devices(PZT). MPPT controller is employed to harvest the maximum power from the PZT and increase efficiency of overall system. The DC-DC boost converter generates a boosted and regulated output at a predefined level and provides energy to load using PMU. A full-wave rectifier using active diodes is used as the AC-DC converter for high efficiency, and a schottky diode type DC-DC boost converter is used for a simple control circuitry. The proposed circuit has been designed in a 0.35um CMOS process. The chip area is $950um{\times}920um$.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.46 no.8
• /
• pp.31-40
• /
• 2009

This paper presents a design of a high performance DC-DC boost converter as a power module for SOC designs. It applied to this chip that reduced inductor and capacitor for integrating on a chip, and it operates with a switching frequency of 100MHz. It has reliability and stability in high switching frequency. The controller of DC-DC boost converter is designed by voltage-mode control method and compensated properly. The designed DC-DC converter is fabricated with the 0.18${\mu}m$ standard CMOS technology with a thick-gate oxide option. The overall die size is 8.14$mm^2$, and controller size is 1.15$mm^2$. The converter has the maximum efficiency over 76% for the output voltage of 4V and load current larger 300mA. The load regulation is 0.012% (0.5mV) for the load current change of 100mA.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2012.10a
• /
• pp.247-250
• /
• 2012

This paper describes a DC-DC Boost converter for Thermoelectric Energy Harvesting. The designed converter boosts the $V_{DD}$ through a start-up block from a low output voltage of thermoelectric devices and the boosted $V_{DD}$ is used to operate the internal block circuits. When $V_{DD}$ reaches a predefined value, a detector circuit makes the start-up block turn off for minimizing current consumption. The final boosted $V_{OUT}$ is achieved by alternately operating the DC-DC converter for $V_{DD}$ and the other converter for final output $V_{OUT}$ according to the comparator output. Simulation results shows that the designed converter outputs 2.8V from an input voltage of 200mV. The area of the chip designed using a 0.35um CMOS process is $1.52mm{\times}0.95mm$ including pads.

• Journal of IKEEE
• /
• v.24 no.3
• /
• pp.853-858
• /
• 2020

This paper proposes a 2-ch DC-DC converter for OLED display with immunity against RF noise inserted from communication device. For RF signal immunity, an input voltage variation reduction circuit that attenuates as much as the input voltage variation is embedded. The boost converter for positive voltage V_POS operates in SPWM-PWM dual mode and has a dead time controller to increase power efficiency. The inverting charge pump for negative voltage V_NEG is a 2-phase scheme and operates in PFM using VCO to reduce output ripple voltage. Simulation results using 0.18 ㎛ BCDMOS process show that the overshoot and undershoot of the output voltage decrease from 10 mV to 2 mV and 5 mV, respectively. The 2-ch DC-DC converter has power efficiency of 39%~93%, and the power efficiency of the boost converter is up to 3% higher than the conventional method without dead time controller.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2018.10a
• /
• pp.31-34
• /
• 2018

This paper presents a low-power buck-boost converter for multi-input energy harvesting systems. The designed circuit combines the energy harvested from three input channels in real time and stores it in a storage capacitor. The structure of the buck-boost converter is simplified by using one external inductor and applying time division technique using an arbiter. In addition, to improve the efficiency of the system, the controller circuits of the converter are designed so that current consumption is minimized. The proposed circuit is designed with $0.35{\mu}m$ CMOS process. Simulation results show that the designed circuit consumes up to 490nA of current when all three input channels are active, and the maximum power efficiency is 92%. The chip area of the designed circuit is $1310{\mu}m{\times}1100{\mu}m$.

• Journal of IKEEE
• /
• v.23 no.3
• /
• pp.1104-1107
• /
• 2019

This paper proposes a DC-DC boost converter for wearable AMOLED display using dead time controller to reduce dead time and improve power efficiency. Also the DC-DC boost converter adopts PWM-SPWM (set-time variable pulse width modulation) dual-mode to enhance power efficiency under light load and decrease output voltage ripple. The proposed circuit has been designed using $0.18{\mu}m$ BCDMOS process. Simulation results show that the circuit has power efficiency of 39%~96% and output ripple voltage of 2 mV under load current range of 1 mA~70 mA. The power efficiency of the proposed circuit is up to 2% higher than the previous PWM-SPWM method and up to 8% higher than only PWM method.

• 전자공학회논문지 IE
• /
• v.47 no.3
• /
• pp.14-18
• /
• 2010

In this paper, we describe a CMOS DC-DC converter with a variable output voltage(5-7V @100mA) for a portable battery-operated system applications. The proposed DC-DC converter is used along with a Pulse-Frequency Modulation (PFM) method and consists of reference circuit, a feedback resistor, a controller, and an internal oscillator. The integrated DC-DC converter with two external passive components(L,C) has been designed and fabricated on a 0.5um 2-poly 3-metal CMOS process and could be applied to the Personal Digital Assistants(PDA), cellular Phone, Laptop Computer, etc.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2013.10a
• /
• pp.361-364
• /
• 2013

Since the non-overlapping gate driver used in conventional DC-DC boost converters generates fixed dead-times, the converters suffer from the body-diode conduction loss or the charge-sharing loss. A adaptive control method has been proposed to reduce these loses. In this method, however, occurrence of and overlapping time of two power transistors in CCM results in reduction of efficiency. In this paper, to overcome this problem a new adaptive control method in proposed, and a DC-DC boost converter with the proposed adaptive control and power switching has been designed in a 0.35um CMOS process. The designed converter outputs 3.3V from a input voltage of 2.5V. The switching frequency is 500kHz and the maximum power efficiency is 95.3% at a load current 150mA. The designed chip area is $1720um{\times}1280um$.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.52 no.2
• /
• pp.89-96
• /
• 2015

This paper presents a high efficiency, PSM/DCM/CCM triple mode boost DC-DC converter for mobile application. This device operates at Pulse-Skipping Mode(PSM) when it enters light load, and otherwise operate the operating frequency of 1.4MHz with Pulse-Width Modulation(PWM) mode. Especially in order to improve the efficiency during the Discontinuous-Conduction Mode(DCM) operation period, the reverse current prevention circuit and oscillations caused by the inductor and the parasitic capacitor to prevent the Ringing killer circuit is added. The input voltage of the boost converter ranges from 2.5V ~ 4.2V and it generates the output of 4.8V. The measurement results show that the boost converter provides a peak efficiency of 92% on CCM and 87% on DCM. And an efficiency-improving PWM operation raises the efficiency drop because of transition from PWM to PFM. The converter has been fabricated with a 0.18um Dongbu BCDMOS technology.