• Journal of the Korean Ceramic Society
• /
• v.18 no.1
• /
• pp.41-47
• /
• 1981

The sintering characteristics of the SiC-Clay-Kaolin chamotte system were studied by addition of $Al_2O_3$ for the manufacture of silicate-bonded silicon carbide refractories at $1350^{\circ}C$. The sinterbilit of SiC-Binder mixture was measured by apparent porosity and compressive strength. And its mineral compositions were identified with X-ray diffractometer. The following results were obtained; 1) Optimum amount of mixed clay ($\textrm{Al}_2\textrm{O}_3$ 40 wt% mixed) as a binder was about 25wt% 2) Appropriate mixing ratio of mixed Kaolin chamotte ($\textrm{Al}_2\textrm{O}_3$ 40wt% mixed) was about 30wt% in the clay Kaolin chamotte binder. 3) Variation of apparent porosity and compressive strength of sintered SiC-binder mixture fired at $1350^{\circ}C$ were due to the sinterbility of clay.

• Journal of Power System Engineering
• /
• v.18 no.1
• /
• pp.14-21
• /
• 2014

Piezoelectric fans are thin elastic beams whose vibratory motion is actuated by means of a piezoelectric material bonded to the beam. These fans have found use as a means to enhance convective heat transfer while requiring only small amounts of power. This study presents new types of models with heat sink having air passage and investigates experimentally their heat transfer characteristics. From the comparison results for four models, the heat transfer coefficients of model 1 are approximately 44~66% higher than those of the reference model 0. The model 1 show the best overall performance about heat transfer and cooling capability. As shown in above results, it is necessary to design the heat sink with air pass for cooling of electronic devices, in order to increase the convective heat transfer coefficient of a piezoelectric fan for electronic cooling.

• Journal of the Korean Ceramic Society
• /
• v.31 no.5
• /
• pp.561-571
• /
• 1994

For the preparation of SiC composite, the properties of reaction sintering in the SiC-C-Si-Ti system with the titanium contents variation were investigated. Either the case of titanium additions or the case of direct infiltration of titanium in SiC+C preform, the newly formed fine-grained $\beta$-SiC, which was reacted from the molten silicon with graphite, was intergranulated between the original $\alpha$-SiC particles. Also titanium disilicide (TiSi2) was discontinuously formed isolated pocket in silicon matrix. The amount of titanium disilicide was gradually increased as titanium content increase. With the results of hardness and fracture toughness measurement, SiC-titanium disilicide (TiSi2) composite represented high properties compared with the system of the infiltrated pure silicon.

• Biotechnology and Bioprocess Engineering:BBE
• /
• v.5 no.1
• /
• pp.17-22
• /
• 2000

The separation of tryptophan enantiomers was carried out with medium-pressure liquid chromatography using BSA (bovine serum albumin)-bonded silica as a chiral stationary phase. The influence of various experimental factors such as pH and ionic strength of mobile phase, separation temperature, and the presence of organic additives on the resolution was studied. In order to expand this system to preparative scale, the loadability of sample and the stability of stationary phase for repeated use were also examined. The separation of tryptophan enantiomers was successful with this system. The data indicated that a higher separation factor (a) was obtained at a higher pH and lower temperature and ionic strength in mobile phase. Addition of organic additives (acetonitrile and 2-propanol) in mobile phase contributed to reduce the retention time of L-tryptophan. About $30\%$ of the separation factor was reduced after 80 days of repeated use.

• Composites Research
• /
• v.17 no.5
• /
• pp.7-14
• /
• 2004

This paper deals with adaptive fuzzy logic controller design to achieve proper dynamic response of a composite thin-walled beam with a tip mass. In order to check the effectiveness of this controller, three different types of control logic are selected and applied. The adaptive control capabilities provided by a system of piezoactuators bonded or embedded into the structure are also implemented in the system. Results show that the fuzzy logic controller is more effective than the proportional or velocity feedback controller for the vibration control of composite thin-walled beam with a tip mass.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.28 no.3_4
• /
• pp.491-498
• /
• 2004

Among the components of disposable diaper, the top sheet contacting with baby skin directly is usually made of nonwoven fabrics. Therefore, the tactile properties of the nonwoven fabrics are important for the skin health of infants. In this study, we have explored the surface properties of hygiene nonwoven fabrics (100% cotton spunlace, 100% tencel spunlace, 100% polypropylene (PP) thermalbonding and 100% PP Thru-air bonded carded web (TABCW)), such as friction coefficient and geometrical roughness. used by KES-F system and a laser displacement sensor. Also, we evaluated the subjective responses about the hygiene nonwoven fabrics used by a questionnaire and compared with the objective values, measured by KES-F system and a laser displacement sensor respectively. From the result, we have found that surface sensation (such as soft, smooth, and rough) and bulkiness sensation (such as spongy and fluffy) of nonwovens were represented excellently by L-SMD values which are measured by a laser displacement sensor.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.11a
• /
• pp.950-957
• /
• 2003

This paper deals with adaptive fuzzy logic controller design to achieve proper dynamic response of a composite thin-walled beam with a tip mass. In order to check the effectiveness of this controller, three different types of control logic are selected and applied. The adaptive control capabilities provided by a system of piezoactuators bonded or embedded into the structure are also implemented in the system. Results show that the fuzzy logic controller is more effective than the proportional or velocity feedback controller for the vibration control of composit thin-walled beam with a tip mass.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.05a
• /
• pp.561-562
• /
• 2006

To enhance the precision and productivity of ultra precision aspheric surface micro lens, the development of ultra-precision grinding system and process for the aspheric surface micro lens are described. In the work reported in this paper, an ultra-precision grinding system for manufacturing the aspheric surface micro lens was developed by considering the factors affecting the grinding surface roughness and profile accuracy. This paper deals with mirror grinding of an aspheric surface micro lens by resin bonded diamond wheel and spherical lens of BK7. The optimization of grinding conditions on ground surface roughness and profiles accuracy is investigated using the design of experiments.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.05a
• /
• pp.303-310
• /
• 2002

The bending vibration and thermal flutter instability of spacecraft booms modeled as circular thin-walled beams of closed cross-section and subjected to thermal radiation loading is investigated in this paper. Thermally induced vibration response characteristics of a composite thin walled beam exhibiting the circumferantially uniform system(CUS) configuration are exploited in connection with the structural flapwise bending-lagwise bending coupling resulting from directional properties of fiber reinforced composite materials and from ply stacking sequence. The numerical simulations display deflection time-history as a function of the ply-angle of fibers of the composite materials, damping factor, incident angle of solar heat flux, as well as the boundary of the thermal flutter instability domain. The adaptive control are provided by a system of piezoelectric devices whose sensing and actuating functions are combined and that an bonded or embedded into the host structure.

• Macromolecular Research
• /
• v.13 no.5
• /
• pp.385-390
• /
• 2005

The electrospinning process is a fascinating method to fabricate small nanosized fibers of diameter several hundred nanometers. Surfactant-polymer solutions were prepared by adding poly(vinyl alcohol) (PVOH) to distilled water with cationic, anionic, amphoteric, and non-ionic surfactants. Average diameter of the electrospun PVOH fibers prepared from PVOH solution was over 300 nm, and was decreased to 150 nm for the mixture of PVOH/amphoteric surfactant. To explain the formation of ultra fine fiber, the characteristic properties in a mixture of PVOH/surfactant such as surface tension, viscosity, and conductivity were determined. In this paper, the effect of interactions between polymers with different classes of surfactants on the morphological and mechanical properties of electrospun PVOH nonwoven mats was broadly investigated.