• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.21 no.2
• /
• pp.322-332
• /
• 2017

Wireless Body Area Networks is an environment that provides an appropriate service remotely by collecting user's biometric information. With the growing importance of sensor, WBAN also attracts extensive attention. Since WBAN is representatively used in the medical field, it can be directly related to the patient's life. Hence security is very important in WBAN. Mutual authentication between the client and the application provider is essential. And efficiency is also important because a used device is limited to computation cost. In this reason, ID-based anonymous authentication scheme in WBAN has been intensively studied. We show that the recent research result of Wu et al. which is about the ID-based anonymous authentication scheme is vulnerable to impersonation attack. And we propose a new ID-based anonymous authentication scheme that is secure against the attacks discovered in the existing schemes. Compared to the existing schemes, the computation cost of our scheme is improved by 30.6% and 7.3%.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.10 no.1
• /
• pp.103-110
• /
• 2015

WBAN(Wireless Body Area Network) is a Wireless Sensor Network for supporting various applications around body within 2~3m which consists of medical and non-medical device. MAC in WBAN environment should satisfy requirements such as low power consumption, various transmission rate, QoS, and duty-cycle, efficiently distribute frequency band, be strong at traffic load and save energy. This paper proposes AQ(Adaptive Queuing) MAC superframe structure for efficient energy use, considering the increase of traffic load. The simulation result also show that transmission rate and average MAC delay rate is improved comparing IEEE 802.15.4 MAC with AQ MAC.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.38B no.5
• /
• pp.315-327
• /
• 2013

Wireless Body Area Network (WBAN) is a network around a human body within 3~5m which consists of medical or non-medical device. WBAN has to satisfy many kinds of demands such as low-power, a variety of data rate and a data priority. Especially, it is hard for the nodes for monitoring vital signs to replace battery. Thus energy and channel efficiency is important because the battery power is limited. In this thesis, a novel algorithm for reducing the energy consumption is proposed. The proposed algorithm adjusts transmission period according to traffic. by means of determining transmission period by amount of data, the node can reduce energy consumption. Energy detection is performed in order to guarantee data priority before attempting to transmit. In case of failing to transmit, it is proposed that energy consumption is reduced through avoiding collision by changing priority. The comparison result shows that the proposed algorithm reduces power consumption and increasing maximum channel efficiency by avoiding collision.

• Journal of the Ergonomics Society of Korea
• /
• v.24 no.1
• /
• pp.43-46
• /
• 2005

The future information technologies and service paradigm will move from PC, the general purpose desktop computing environment, to the next-generation PC that provides information any where, any time, and any device. The next-generation PC such as wearable computers are specialized to the human-centric functionalities and always-on connected services. In this study, service infrastructure of wearable computing with WBAN(Wearable Body Area Network) was suggested for the ubiquitous computing environment.

• Journal of Advanced Navigation Technology
• /
• v.18 no.6
• /
• pp.640-647
• /
• 2014

The WBAN technology means a short distance wireless network which provides each device's interactive communication by connecting devices inside and outside of body located within 3 meters. It is necessary to develop core technology that the WBAN middleware and application service for WBAN sensor network. A device for gathering patient's biometric information was used zigbex of Hanbaek electronics and we designed the message structure which is collected the biometric information. The gateway design and implementation for the WBAN environment. The embedded system was HBE-empos II of Hanbaek electronics and the WBAN network is implemented to BNC and BN that used for hbe-ubi-zigbex. It was confirmed that the proposed sensor gateway could be used for the interconnection of the proposed system with other networks.

• Journal of Korea Multimedia Society
• /
• v.15 no.10
• /
• pp.1264-1272
• /
• 2012

Three-dimensional volume rendering method which shows the inside of human body is widely used in medical imaging area. Existing medical imaging system using a volume rendering method already has provided a variety of three-dimensional results. Recently existing results in the medical imaging among physicians and patients to facilitate communication have been studied since smart device which has advantage of portability applied in the medical imaging. In this paper, we propose 3D volume visualization system for a relatively low spec portable smart devices by using 2D textures and we also implements 2D diagnostic images of portable medical imaging visualization system.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.26 no.8
• /
• pp.635-639
• /
• 2013

Generating output characteristics of a EYE-type piezoelectric generator depending on ceramic size and materials of the elastic body were studied. EYE-type piezoelectric-generating device consist of the ceramic was attached between the both elastic body. piezoelectric-generating is that if the tension occurred at both ends of an elastic body, the piezoelectric effect occurs at ceramics through the form change of the elastic body. The structure of this EYE-type generator use various area. than a existing type generator, because the ceramic position of the directly force at does not apply. Resonance and output characteristics of the generator were analyzed by using FEM program. Generators were fabricated on the basis of analyzed results and attached on a frequency controllable vibrator to measure output characteristics. Also, the experimental results were compared with the simulated results. As a result, output characteristics of the generator increased depending on the increase in ceramic thickness. In case of increase in ceramic width, resonance frequency of the generator also decreased.

• Proceedings of the ESK Conference
• /
• 1995.04a
• /
• pp.155-164
• /
• 1995

For efficient operation, vital hand controls must be easily controlled by the operator from his normal working position. The primary working area based on operator's working comfort was developed to serve as a design guideline tothe control panel layout. Ten male subjects participated in the experiment in which working comfort was measured for two controls of a lever type control and a knob type control with respect to the frontal and sagittal distances from the body center and the slope of a workplace. The response surface methodolgy using a central composite design was employed to develop a prediction model for perceived working comfort of each control. Both controls have a similar pattern of comfortable working area, but the lever type control has slightly broader working area. The concept of the proposed working area is a significant extension to the conventional working area such as Farley's or Squires' curves. It is shown that the distance toa control device and the slope have a quadratic effect to working comfort. It is noticeable that comfortable working area exists outside the conventional working area. The result of the response surface analysis also indicated that a little slope of about 15 .deg. for a control panel improves working comfort.

• Korean Journal of Digital Imaging in Medicine
• /
• v.16 no.1
• /
• pp.7-11
• /
• 2014

The body to achieve an interaction that are connected to each other. Foot of which plays an important role in motor activity. Insole that has been recently used, have a dynamic functional elements. In particular, support of Arch plays a very important role in terms of a motor function of the human body as a whole. It is possible to predict the proper support Arch with insole, the overall structure of the body there can affect the balance. In this study, by applying the insole which supports the Longitudinal arch and Transverse arch, you are trying to assess the interaction of balance and the body's ability. To target the 20 there is no problem in the sense of balance, college student, and changes were observed by measuring the Center of Position area and distance through the Biorescue device worn before and after led by Arch support. As a result, I showed improved results significantly discount rate after wearing in the Center of Position area and distance to assess the balance ability. Therefore, the correction insole function is to support the Longitudinal arch and Transverse arch to an important role in the foot. It may be that it has a functional element for improving the balance of the function of preventing collapse of the arch during walking, to disperse the weight of the entire foot, us reduce fatigue in the end.

• The Journal of Korean Academy of Prosthodontics
• /
• v.45 no.5
• /
• pp.687-695
• /
• 2007

Statement of problem: The proper contact relation between adjacent teeth in each arch plays an important role in the stability and maintenance of the integrity of the dental arches. Proximal contact has been defined as the area of a tooth that is in close association, connection, or touch with an adjacent tooth in the same arch. Purpose: The aim of this study was to develop a digital device for measuring the proximal tooth contact tightness by pulling a thin stainless steel strip (2mm wide, 0.03mm thick) inserted between proximal tooth contact. Material and method: This device consists of measuring part, sensor part, motor part and body part. The stainless steel strip was connected to a stain gauge. The strain gauge was designed to convert the frictional force into a compressive force. This compressive force was detected as a electrical signal and the electrical signal was digitalized by a A/D converter. The digital signals were displayed by a micro-processor. The pulling speed was 8mm/s. Results: For testing reliability of the device in vivo, two healthy young adults (A, B) participated in this experiment. The tightness of proximal tooth contact between the second premolar and the first molar of mandible (subject A) and maxilla (subject B) was measured fifteen times for three days at rest. We double-checked the accuracy of the device with a Universal Testing Machine. Output signals from the Universal Testing Machine and the measuring device were compared. Regression analysis showed high linearity between these two signals. In vivo test, no significant differences were found between measurements. Conclusion: This device has shown to he capable of producing reliable and reproducible results in measuring proximal tooth contact. Therefore, it was considered that this device was appropriate to apply clinically.