• Transactions on Electrical and Electronic Materials
• /
• v.1 no.3
• /
• pp.23-28
• /
• 2000

A block-oxide layer was formed on the surface of Cu-based leadframe by chamical oxidation method in order to enhance the adhesion strength between Cu-based leadframe and epoxy molding compound (EMC) Using sandwiched double cantilever beam (SDCB) specimens, the adesion strength was measured in terms of interfacial fracture toughness, G$\sub$IC//Results showed that the black-oxide layer was composed of two kinds of layers: pebble-like Cu$_2$O layer and acicular CuO layer, At the initial stage of oxidation the Cu$_2$O layer was preferentially formed and thickened up to around 200 nm whithin 1 minute of the oxidation time. Then the CuO layer started to from atop of the Cu$_2$O layer and thickened up to around 1300 nm until 20 minutes. As soon as the CuO layer formed, the thickness of Cu$_2$O layer began to reduce and finally reached to around 150 nm. The pre-cleaned and the Cu$_2$O coated leadframes showed almost no adhesion of EMC, however, as the CuO precipitates appeared and became continuous, G$\sub$IC/ increased up to around 80 J/㎡. Further oxidation raised G$\sub$IC/ up. to around 100 J/㎡.

• Korean Journal of Materials Research
• /
• v.15 no.1
• /
• pp.1-5
• /
• 2005

Copper-based leadframe sheets were immersed in two kinds of hot alkaline solutions to form brown-oxide or black-oxide layer on the surface. The oxide-coated leadframe sheets were molded with epoxy molding compound (EMC). After post mold curing, the oxide-coated EMC-leadframe joints were machined to form sandwiched double-cantilever beam (SDCB) specimens. The SDCB specimens were used to measure the fracture toughness of the EMC/leadframe interfaces under quasi-Mode I loading conditions. Fracture surfaces were analyzed by various equipment to investigate failure path. The present paper deals with the failure path, and the cause of the failure path formation with an adhesion model will be treated in the succeeding paper.

• Journal of the Korean Applied Science and Technology
• /
• v.31 no.2
• /
• pp.176-182
• /
• 2014

Using alkali treatment solution, neutrality treatment solution and acid treatment solution, the surface corrosion layer of copper plates and bronze plates that have been artificially corroded using HCl, $H_2SO_4$ and $HNO_3$ solutions were removed. In the case of alkali treatment solution, only air oxidation in the form of black tenorite and white cuproous chloride remained without being removed. In the case of using a neutrality treatment solution, a anhydrous type layer of reddish brown cupric chloride remained without being removed, together with this black and white corrosion substance. In the case of using an acid treatment solution, this red corrosion substance also remained, but all of the oxide was removed on the surface of the specimen that was treated by alternatively using alkali treatment solution and acid treatment solution. In the case of this treatment solution with the order of alkali-acid, oxidation no longer proceeded only through the distilled water cleaning process after treatment, thereby showing that oxidation from the cleaning solution no longer proceeded.

• Journal of the Korean institute of surface engineering
• /
• v.32 no.6
• /
• pp.647-657
• /
• 1999

Due to the inherently poor adhesion strength of Cu-based leadframe/EMC (Epoxy Molding Compound) interface, popcorn cracking of thin plastic packages frequently occurs during the solder reflow process. In the present work, in order to enhance the adhesion strength of Cu-based leadframe/EMC interface, black-oxide layer was formed on the leadframe surface by chemical oxidation of leadframe, and then oxidized leadframe sheets were molded with EMC and machined to form SDCB (Sandwiched Double-Cantilever Beam) and SBN (Sandwiched Brazil-Nut) specimens. SDCB and SBN specimens were designed to measure the adhesion strength between leadframe and EMC in terms of critical energy-release rate under quasi-Mode I ($G_{IC}$ ) and mixed Mode loading ($G_{C}$ /) conditions, respectively. Results showed that black-oxide treatment of Cu-based leadframe initially introduced pebble-like X$C_2$O crystals with smooth facets on its surface, and after the full growth of $Cu_2$O layer, acicular CuO crystals were formed atop of the $Cu_2$O layer. According to the result of SDCB test, $Cu_2$O crystals on the leadframe surface did not increase ($G_{IC}$), however, acicular CuO crystals on the $Cu_2$O layer enhanced $G_{IC}$ considerably. The main reason for the adhesion improvement seems to be associated with the adhesion of CuO to EMC by mechanical interlocking mechanism. On the other hand, as the Mode II component increased, $G_{C}$ was increased, and when the phase angle was -34$^{\circ}$, crack Kinking into EMC was occured.d.

• Korean Journal of Materials Research
• /
• v.14 no.5
• /
• pp.322-327
• /
• 2004

Copper-based leadframe sheets were oxidized in two kinds of hot alkaline solutions to form brown-oxide or black-oxide layer on the surface. The oxide coated leadframe sheets were molded with epoxy molding compound (EMC). After post mold curing, the oxide-coated EMC-leadframe joints were machined to form sandwiched Brazil-nut (SBN) specimens. The SBN specimens were used to measure the fracture toughness of the EMC/leadframe interfaces under mixed-mode (mode I + mode II) loading conditions. Fracture surfaces were analyzed by various equipment to investigate failure path. The results revealed that the failure paths were strongly dependent on the oxide type. In case of brown oxide, hackle-type failure was observed and failure path lay near the EMC/CuO interface with a little inclining to CuO at all case. On the other hand, in case of black oxide, quite different failure path was observed with respect to the distance from the tip of pre-crack and phase angle. Different failures occurred with oxide type is presumed to be due to the difference in microstructure of the oxides.

• Applied Microscopy
• /
• v.47 no.3
• /
• pp.176-186
• /
• 2017

Two-dimensional (2D) materials have been studied widely owing to their outstanding properties since monolayer graphene was isolated in 2004. Especially, among 2D materials, phosphorene, a single atomic layer of black phosphorus (BP), has been highlighted for its electrical properties. This material can serve as a substitute for graphene, which has been revealed as a "semi-metal", in next-generation semiconductors. However, few-layer BP is prone to degradation under ambient conditions owing to its reactivity with oxygen and water, which results in the condensation of water droplets on the surface of the BP flakes. This causes charge transfer from the phosphorus atom to oxygen, resulting in the formation of phosphoric acid (oxide) and degrades the various properties of BP. Therefore, it is necessary to find passivation methods to prevent BP flakes from being degraded under ambient conditions. This review article deals with recent studies on passivation methods for BP and their performance against oxygen and water, effects on the electrical properties of BP, and the extent to how they protect BP.

• Journal of Conservation Science
• /
• v.35 no.6
• /
• pp.573-587
• /
• 2019

In this study, reproducing specimens were made from mixing domestically produced magnetite, clay and non-plastic raw materials to reproduce the pigments used in the manufacture of traditional cheolhwa buncheong stoneware. In order to reveal the color fomation of glaze, 30 specimens with good color development were analyzed scientifically. Magnetite, which is the main raw material of the pigment, is a pigment capable of creating a dark black color in a reducing environment at 1,200℃. However, it reacts with the additionally added lime component and discolors to greenish yellow color in oxidizing environment at 1,230℃. Hematite is not significantly affected by the firing temperature and environment, but develops a dark black color when mixed with clay with iron content of more than 10%. The fluidity of the pigment is determined by R₂O₃/RO₂ value, which also affects the color development. In the microtexture observation, the color formation of the glaze layer and the iron oxide crystals identified some differences depending on the particle size of the pigment and the firing environment. Reproduced specimens made of magnetite are present in the form of aggregates of iron oxide in the interface between glaze layer and slip layer in the oxidizing environment at 1,200℃. However, in the reducing environment, aggregates of iron oxides do not exist in the reproduced specimens, and they are homogeneously distributed in the glaze layer and formed a dark black color. In contrast, hematite-based specimens form dendritic structures in the glaze layer in an oxidizing environment and develop black.

• Journal of Conservation Science
• /
• v.37 no.2
• /
• pp.77-89
• /
• 2021

In this study, materials and color formation techniques were assessed for black potteries excavated from the Janghyeon-dong, Jungsan-dong and Gyodong-ri sites during the Proto-Three Kingdoms period in Ulsan, Korea. Although the black potteries were black superficially, the inner cores were either black or reddish yellow. Microscopy analysis identified that body clay was used for reddish iron oxide rich soils with quartz, alkali feldspar and mica, along with grains of myrmechite texture. Additionally, as marginal differences exist in the contents of SiO₂, Fe₂O₃ and CaO, the composition of the host rock and clay distributed around the sites was affected. Thus, we can deduce that pottery was made by soiling at a short distance. Raman spectroscopy results revealed that the black layer of the black pottery was used as amorphous combustion carbon. In addition, as a transparent layer of brown lacquer was observed on the substrate that was in contact with the surface layer, the black layer of the pottery induced black color development by a combination of combustion carbon and lacquer. Based on the mineral composition and microtexture of the body clay, the firing temperature of the potteries seemed to range from 750 to 850℃, whereas the lacquer layer was pyrolyzed at 468℃ by thermal analysis. Therefore, a combined layer of combustion carbon and lacquer, which formed the black color, was painted after the body clay was fired.

• Korean Journal of Food Science and Technology
• /
• v.50 no.5
• /
• pp.528-534
• /
• 2018

The current study investigated the effects of enzyme treatment on black rice (Oryza sativa L.) aleurone layer extracts. Different enzymes (lipase, lecitase ultra and lipopan 50BG) were used to test anti-oxidant and anti-inflammatory activities in vitro. The antioxidant activities of enzyme treated or non-enzyme treated extracts of black rice bran were evaluated via 1,1-diphenyl-2-picrylhydrazyl radical scavenging activity and 2,2'-azino-bis(3-ethylbenzothiazoline-6-sulfonic acid) radical scavenging activity. Lipase treated extracts of black rice bran showed higher antioxidant activity compared to that of non-enzyme treated extracts. Anti-inflammatory activities of enzyme treated black rice bran extracts on nitrite production and tumor necrosis $factor-{\alpha}$ ($TNF-{\alpha}$) secretion, were tested using a nitric oxide (NO) colorimetric assay kit and an enzyme-linked immunosorbent assay (ELISA) kit. The ethanolic extract of enzyme treated black rice bran decreased the levels of nitric oxide production and pro-inflammatory cytokines, such as tumor necrosis $factor-{\alpha}$, in a lipopolysaccharidestimulated RAW 264.7 cell culture. These findings indicate that enhanced anti-oxidant and anti-inflammation activities of the ethanolic extracts of enzyme treated black rice (Oryza sativa L.) aleurone layers, may be attributed to molecular conversion of ingredients in enzyme catalyzed reactions.

• Journal of Conservation Science
• /
• v.36 no.5
• /
• pp.393-404
• /
• 2020

We observed changes in the properties of the glaze layer according to the content of iron oxide and inferred the composition, content, and environment of the materials used in the past during the production process of black ware. First, experiments were conducted using different ratios of iron oxide, feldspar, calcite, and ash at different temperatures and firing environments; the characteristics of glaze were classified into five groups in the oxidation environment. Different properties were identified in the reducing environment above 1200℃. The crystal identified in the experiment was similar to the glaze characteristics in the excavated black ware. The crystal phase appeared in four groups: band shape, circular, arborescent phase, and needle crystal, depending on the change in the content of iron oxide. However, the difference in crystals did not appear significantly at high temperatures. In addition, crystals of glaze were divided into two groups depending on the component ratio. The presence or absence of feldspar is thought to affect crystallinity and amorphous iron oxide and the changes in the glaze layer changed substantially depending on the amount of iron oxide. In particular, it was confirmed that the aspects of iron oxide in the oxidation and reduction environments were different and, therefore, crystallization due to the firing environment also affected the optical characteristics.