• 한국도로학회논문집
• /
• 제14권4호
• /
• pp.51-61
• /
• 2012

PURPOSES : This study deals with the working life of polymer concrete, which is typically used as a repair or overlay material for portland cement concrete pavements. METHODS : In the scope of this study, laboratory testing was conducted on fresh MMA modified UP polymer concrete, which uses an MMA monomer for viscosity adjustment and strength improvement of UP resin. The experimental variables were temperature (-20 to $+20^{\circ}C$) and binder components (MMA, MEKPO, and DMA). RESULTS : The result showed that the optimum binder ratios for polymer concrete production were 12, 11, and 10 wt.% when the MMA contents were 20, 30, and 40 wt.%, respectively. The working life of polymer concrete depending on temperature and binder components could be expressed by a logarithmic functional formula. The coefficient of variation for each binder component was the highest for DMA content while the lowest for MEKPO content. Also, the contents of each binder component for ensuring the working life of 60 minutes were proposed. CONCLUSIONS : Ultimately, the present study derived a linear regression equation estimating 60 minutes working life based on the setting times of each binder component.

• 한국재료학회지
• /
• 제32권12호
• /
• pp.538-544
• /
• 2022

In existing ceramic mold manufacturing processes, inorganic binder systems (Si-Na, two-component system) are applied to ensure the effective firing strength of the ceramic mold and core. These inorganic binder systems makes it possible to manufacture a ceramic mold and core with high dimensional stability and effective strength. However, as in general sand casting processes, when molten metal is injected at room temperature, there is a limit to the production of thin or complex castings due to reduced fluidity caused by the rapid cooling of the molten metal. In addition, because sodium silicate generated through the vitrification reaction of the inorganic binder is converted into a liquid phase at a temperature of 1,000 ℃. or higher, it is somewhat difficult to manufacture parts through high-temperature casting. Therefore, in this study, a high-strength ceramic mold and core test piece with effective strength at high temperature was produced by applying a Si-Na-Ti three-component inorganic binder. The starting particles were coated with binary and ternary inorganic binders and mixed with an organic binder to prepare a molded body, and then heat-treated at 1,000/1,350/1,500 ℃ to prepare a fired body. In the sample where the two-component inorganic binder was applied, the glass was liquefied at a temperature of 1,000 ℃ or higher, and the strength decreased. However, the firing strength of the ceramic mold sample containing the three-component inorganic binder was improved, and it was confirmed that it was possible to manufacture a ceramic mold and core via high temperature casting.

• Elastomers and Composites
• /
• 제57권4호
• /
• pp.197-204
• /
• 2022

Recently, the demand has increased for protective clothing materials capable of shielding the wearer from bullets, fragment bullets, knives, and swords. It is therefore necessary to develop light and soft protective clothing materials with excellent wearability and mobility. To this end, research is being conducted on hybrid design methods for various highly functional materials, such as carbon nanotube (CNT) sheets, which are well known for their low weight and excellent strength. In this study, a hybrid protective material using CNT sheets was developed and its performance was evaluated. The material design incorporated a bonding method that used a binder for interlayer combination between the CNT sheets. Four types of binders were selected according to their characteristics and impregnated within CNT sheets, followed by further combination with aramid fabric to produce the hybrid protective material. After applying the binder, the tensile strength increased significantly, especially with the phenoxy binder, which has rigid characteristics. However, as the molecular weight of the phenoxy binder increased, the adhesive force and strength decreased. On the other hand, when a 25% lightweight-design and high-molecular-weight phenoxy binder were applied, the backface signature (BFS) decreased by 6.2 mm. When the CNT sheet was placed in the middle of the aramid fabric, the BFS was the lowest. In a stab resistance test, the penetration depth was the largest when the CNT sheet was in the middle layer. As the binder was applied, the stab resistance improvement against the P1 blade was most effective.

• 한국분말재료학회지
• /
• 제6권2호
• /
• pp.132-138
• /
• 1999

A new binder system and debinding process for low carbon residue in the injection molding of Nd(Fe, Co)B powder are investigated. In the injection molding of magnetic materials, it is demanded to reduce carbon residue which deteriorates their magnetic properties. The binder system developed is composed of polyethylene glycols (PEGs) and polypropylene (PP). PEG was selected as a major binder is component to be extracted in a molecular state by solvent extraction in ethanol, which step would leave no residue. PP was selected as a minor binder component to be subsequently removed by thermolysis which step would leave carbon residue. The behaviors of solvent extraction with the variations of PEG molecular weight, temperature, and time were examined. The dependency of residual carbon content on thermolysis atmosphere was also studied. Opened pore channels introduced in a green body by the solvent extraction and microstructures of the sintered magnets were observed using SEM.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2007년도 추계학술대회 논문집
• /
• pp.455-456
• /
• 2007

Optically transparent, highly conductive coating have been major theme of thin film science efforts for some years. In this work, t-MWNT(thin Multi-walled Carbon Nanotubes) are acid treated, then the stable dispersion of t-MWNTs in polar solvent such as alcohols, was achieved by sonication. The transparent conducting films are prepared using the one component solution of t-MWNT/epoxy binder via spray coating on glass substrate. The characterization of acid treated t-MWNTs was performed by Raman spectrometer. The opto-electrical properties of conducting films are analyzed by the binder concentration, and the effect of co-solvent on the compatibility and dispersibility of one component t-MWNT/epoxy binder solutions are discussed.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2014년도 춘계 학술논문 발표대회
• /
• pp.142-143
• /
• 2014

In this study, as to enhance the efficiency and workability, binder contained 3 types of gels have been used to replacement the OPC. Fundamental properties and length change of the concrete have been tested to evaluate the effect of different binders. The following results could be made as the conclusion. When the binder contained 3 types of gels used, the flowability increased, whereas the air content decreased. There showed some different air content when the component of binder changed but the difference was consider as limit. For the strength properties, with the using of binder contained 3 types of gels increased the strength. Specimen of FA20SF5 showed the better strength and lower length change of drying shrinkage than other specimens.

• 한국마이크로전자및패키징학회:학술대회논문집
• /
• 한국마이크로전자및패키징학회 2000년도 추계 기술심포지움 논문집
• /
• pp.89-92
• /
• 2000

테입 캐스터를 이용하여 바인더/가소제, 글말함량 비율이 다른 LTCC 테입을 제작한 후 특성평가를 하고자 하였다. 슬러리 조성은 서로 다른 바인더/가소제 그리고 분말함량에 따라 각각 4개 조성으로 구성하였다. 모든 슬러리에서 발포나 핀홀이 없는 미려한 표면을 갖는 테입을 얻을 수 있었다. 가장 우수한 기계적 특성 특성은 B/P=3.0, 분말함량 70vo1%인 두께 52 $\mu\textrm{m}$인 테입에서 인장강도 4.6MPa, 신을 29.5%의 특성을 얻을 수 있었다.

• 한국자기학회지
• /
• 제24권3호
• /
• pp.86-89
• /
• 2014

이방성 희토류 본드자석은 자성분말과 유기 바인더로 구성되며 본드자석 내에서 유기 바인더는 분말의 배향을 유리하게 하는 역할을 한다. 유기 바인더는 고분자 수지, 활제, 경화제, 커플링제 등으로 구성되며 자성분말에 적합한 유기 바인더를 제조하기 위해 본 연구에서는 다양한 성분을 선정하여 유기 바인더를 제조하였고 구성비 및 첨가량을 조절하여 이를 본드자석에 적용하였다. 특성평가를 통해 자기특성 및 기계적 특성을 측정하였고 이로부터 본드자석에 적합한 유기 바인더의 성분 및 비율을 확인하였다.

• 콘크리트학회논문집
• /
• 제27권5호
• /
• pp.559-568
• /
• 2015

본 연구에서는 감수제의 감수 효율에 따른 다성분계 결합재를 사용한 콘크리트의 물리적 특성에 대한 영향을 평가하기 위하여 고성능 감수제의 종류 3수준(0%, 8% 및 16%) 및 물-결합재비 3수준(40%, 45% 및 50%)에 따른 플라이애시 및 고로슬래그 미분말을 사용한 다성분계 콘크리트 배합을 제조하였다. 또한, 신뢰성 확보를 위하여 콘크리트 배합은 3회 반복실험을 실시하였다. 실험결과, 감수제 종류에 따른 압축강도는 약 20% 이상의 압축강도 차이가 발생하였으며, 감수제의 감수 효율이 콘크리트의 품질에 크게 영향을 미치는 것으로 나타났다. 따라서 감수제의 감수 효율을 반영한 다성분계 콘크리트의 압축강도 예측 모델식을 도출하였으며, 90% 이상의 높은 상관성이 있는 것으로 나타났다.

• 보존과학회지
• /
• 제35권4호
• /
• pp.363-372
• /
• 2019

Animal glue has been used as a binder in Dancheong since the Joseon dynasty. Binders play an important role in determining the physical characteristics of a painting layer. The analysis of binders can be used to identify the materials and techniques used in traditional Dancheong. Binders can be investigated using physicochemical component analyses methods such as gas chromatography/mass spectrometry, pyrolysis-gas chromatography/mass spectrometry, and fourier transform infrared spectroscopy, but the detection characteristics vary depending on the degradation properties of the pigment and binder. Therefore, cross-validation using a combination of physicochemical analysis and enzyme immunoassay is used to increase the reliability of the results. In this study, we present an enzyme-linked immunosorbent assay (ELISA) as an example of an enzyme immunoassay as a method for analyzing animal glue, a traditional binder used in Korea. The applicability of ELISA was tested using commercial animal glue, in addition to animal glue produced using a variety of extraction conditions. The animal glue was analyzed in a Noerok-additionally coated-replica sample to evaluate the possibility of analyzing the animal glue in a paint layer mixed with pigment. Based on the results, we performed an assay on the use of animal glue in the Dancheong sample of the temples of the Joseon dynasty, that are estimated to have been built in the 17^th century.