• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2004년도 추계학술대회논문집
• /
• pp.924-927
• /
• 2004

Measurements of fluctuating wall pressures were made with a linear array of 16 piezo-electric transducers beneath a fully-developed turbulent boundary layer. The piezoelectric bimorph actuator applied in this experiment has bonding structures of each polarity to make out-of-plane displacements rather than in-plane ones by using piezoelectric effect To specify the boundary layer characteristics at the location where the actuation was applied, the wall friction coefficients and $Re_\theta$ were measured by using the CPM method. The actuating frequency for the bimorph film was determined according to the priori bursting frequency from boundary layer parameters. The reduction of convecting energies in wave-number space was clearly observed at the specified actuating frequencies.

• 한국정밀공학회지
• /
• 제15권12호
• /
• pp.194-201
• /
• 1998

The beam rotating actuator has been developed. It can be utilized to improve the data transfer rate for the optical disk systems, Newly developed laser beam rotating actuator is applied to put multi-beam spots on more than one track on the optical disk simultaneously. The beam rotating actuator is made of piezoelectric ceramic bimorph as the form of cantilever, Piezoelectric actuators with high resolution, high stiffness and fast frequency response are widely assembled in micropositioning applications. Therefore, the actuator has above 50Hz natural frequency. Beam array is rotated using the dove prism in the end of beamrotator. The dynamic equation of beam rotating actuator is derived theoretically. The actuator is designed on the ground of this analysis. The performance of the beam rotating actuator is verified as the dynamics frequency performance is measured using the dynamic analyzer and sensor.

• Smart Structures and Systems
• /
• 제26권3호
• /
• pp.391-401
• /
• 2020

The present article reports the feasibility of the electrical energy generation from ambient low-frequency vibration using a piezoelectric material mounted on a bimorph cantilever beam actuator. A corresponding higher-order analytical model is developed using MATLAB in conjunction with finite element method under low-frequency with both damped and undamped conditions. An alternate model is also developed to check the material and dimensional viability of both piezoelectric materials (mainly focussed to PVDF and PZT) and the base material. Also, Genetic Algorithm is implemented to find the optimum dimensions which can produce the higher values of voltage at low-frequency frequencies (≤ 100 Hz). The delamination constraints are employed to avoid inter-laminar stresses and to increase the fracture toughness. The delamination has been done using a Teflon sheet sandwiched in between base plates and the piezo material is stuck to the base plate using adhesives. The analytical model is tested for both homogenous and isotropic material characteristics of the base material and extended to investigate the effect of the different geometrical parameters (base plate dimensions, piezo layer dimensions and placement, delamination thickness and placement, excitation frequency) on the model responses of the bimorph cantilever beam. It has been observed that when the base material characteristics are homogenous, the efficiency of the model remains higher when compared to the condition when it is of isotropic material. The necessary convergence behaviour of the current numerical model has been established and checked for the accuracy by comparing with available published results. Finally, using the results obtained from the model, a prototype is fabricated for the experimental validation via a suitable circuit considering Glass fibre and Aluminium as the bimorph material.

• Smart Structures and Systems
• /
• 제16권5호
• /
• pp.759-780
• /
• 2015

Based on the theory of piezoelasticity, the static performance of a piezoelectric bilayer cantilever fully covered with electrodes on the upper and lower surfaces is studied. Three models are considered, i.e., the sensor model, the driving displacement model and the blocking force model. By establishing suitable boundary conditions and proposing an appropriate Airy stress function, the exact solutions for piezoelectric bilayer cantilevers are obtained, and the effect of ambient thermal excitation is taken into account. Since the layer thicknesses and material parameters are distinguished in different layers, this paper gives unified solutions for composite piezoelectric bilayer cantilevers including piezoelectric bimorph and piezoelectric heterogeneous bimorph, etc. For some special cases, the simplifications of the present results are compared with other solutions given by other researches based on one-dimensional constitutive equations, and some amendments have been found. The present investigation shows: (1) for a PZT-4 piezoelectric bimorph, the amendments of tip deflections induced by an end shear force, an end moment or an external voltage are about 19.59%, 23.72% and 7.21%, respectively; (2) for a PZT-4-Al piezoelectric heterogeneous bimorph with constant layer thicknesses, the amendments of tip deflections induced by an end shear force, an end moment or an external voltage are 9.85%, 11.78% and 4.07%, respectively, and the amendments of the electrode charges induced by an end shear force or an end moment are both 1.04%; (3) for a PZT-4-Al piezoelectric heterogeneous bimorph with different layer thicknesses, the maximum amendment of tip deflection approaches 23.72%, and the maximum amendment of electrode charge approaches 31.09%. The present solutions can be used to optimize bilayer devices, and the Airy stress function can be used to study other piezoelectric cantilevers including multi-layered piezoelectric cantilevers under corresponding loads.

• 한국소음진동공학회논문집
• /
• 제13권3호
• /
• pp.225-231
• /
• 2003

A new three-dimensional thin shell element for a structure containing an integrated distributed piezoelectric sensor and actuator is Proposed. The assumed strain formulation and the bubble function are introduced to improve the performance of the shell element. A finite element formulation gives a general tool that can predict the static or dynamic responses of the shell with piezoelectric sensor/actuator. The verification through the calculation of the static response for the piezoelectric bimorph beam shows that the results agree with those from the theoretical analysis very well. Dynamic response of a shell shows that the reduction of vibration is possible with the introduction of the piezoelectric shell sensor and actuator. However. the curvature of sensor/actuator is an obstacle for application, since the flexible PVDF is not strong enough and the PZT with curvature should be made specially.

• 한국음향학회지
• /
• 제22권3호
• /
• pp.202-207
• /
• 2003

초음파트랜스듀서는 초점거리의 제어를 위해서 각 진동요소에 전기회로를 이용한 위상가중치를 부가하는 방식을 사용하고 있다. 그러나 이러한 방법은 진동요소가 증가함에 따라 전기회로가 더욱 복잡해진다. 본 연구에서는 바이몰프형 액츄에이터를 신호의 송수신을 하는PVDF의 뒷부분에 삽입하여 선집속형 트랜스듀서를 제작하였다. 이 트랜스듀서를 사용하여 액츄에이터에 인가되는 전압 변화에 의해 기계적으로 초점거리를 제어할 수 있었다. 이 방법을 사용한 결과 수중에서 선집속형 초음파 트랜스듀서의 초점거리를 곡률 반경의 10%범위까지 제어 가능함을 확인하였다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2003년도 춘계학술대회 논문집
• /
• pp.828-831
• /
• 2003

The benefits of the pneumatic valve with piezoelectric element are faster response times, low energy consumption, and the ability to be used in hazardous environments and field bus systems. In this paper, PZT actuator, 2 and 3 stages pneumatic valve were designed and manufactured. Also. characteristics of the pneumatic valve with piezoelectric element were tested with a testing system. It is confirmed that the PZT actuator is useful one for controlling the direction of pilot valve.

• 한국전기전자재료학회논문지
• /
• 제29권10호
• /
• pp.601-607
• /
• 2016

Piezoelectric thick films of soft $Pb(Zr,Ti)O_3$ (PZT) based commercial material (S55) were fabricated using a conventional tape casting method. Ag-Pd electrodes were printed on the piezoelectric film at room temperature and all 5 layered films with a dimension of $12mm{\times}16mm$ were successfully laminated for a multi-layered piezoelectric ceramic actuator. The laminated specimens were co-fired at $1,100^{\circ}C$ for 1 h. A flat layered and dense microstructure was obtained for the $112{\mu}m$ thick piezoelectric actuator after sintering process. Thereafter, a prototype piezoelectric speaker was fabricated using the multi-layered piezoelectric ceramic actuator which can operate as a bimorph. Its SPL (sound pressure level) characteristic was also evaluated for speaker application. Frequency response revealed that the output SPL with a root mean square voltage of 10 V increased gradually to the highest peak of 87.5 dB for 1.5 kHz and exhibited a relatively stable behavior over the measured frequency range (${\leq}20kHz$) at a distance of 10 cm, implying that the fabricated piezoelectric speaker is potential for speaker applications.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2004년도 추계학술대회논문집
• /
• pp.407-412
• /
• 2004

본 연구에서는 PMN-PT bimorph actuator를 이용하여 초소형 광디스크 드라이브용 광픽업 구동기를 제작하였다. 최근에 휴대용 기기에서의 고용량 정보 저장기기에 대한 필요성이 대두됨에 따라 착탈식이 가능한 수 기가급 초소형 광디스크 드라이브가 개발중에 있다. PMN-PT는 약 1.5kV/cm 이하의 전기장에서는 PZT같은 압전 소자와 마찬가지로 입력 전압에 대한 변형률이 선형성을 나타내는데, 사용된 PMN-PT는 PZT의 약 3배 가까운 압전 상수값을 나타내었다. 보 끝단에 외부 힘이 작용할 때 PMN-PT bimorph 구동기가 낼 수 있는 수직 방향의 힘과 변위에 대해서 일반적인 적층 형태로 이론적인 해석을 수행 하였다. 그리고 이 bimorph로 구동될 Cymbal 형태의 변위 확대 기구의 변위에 대한 이론적인 모델을 제시하고, 이를 이용하여 2개의 bimorph로 2축을 동시에 구동하는 픽업 구동기를 제작하였다. 3개의 제작된 prototype으로 실험을 수행하여 예상 변위량과 잘 일치함을 보였다. 또한, 상용 해석 프로그램인 Matlab과 Ansys를 이용하여 Cymbal 확대 기구의 여러 파라미터에 따른 구동 성능의 민감도를 확인해 보았다.

• 대한기계학회논문집A
• /
• 제30권4호
• /
• pp.409-419
• /
• 2006

The actuating performance of plate-type unimorph piezoelectric composite actuators having various stacking sequences was evaluated by three dimensional finite element analysis on the basis of thermal analogy model. Thermal residual stress distribution at each layer in an asymmetrically laminated plate with PZT ceramic layer and thermally induced dome height were predicted using classical laminated plate theory. Thermal analogy model was applied to a bimorph cantilever beam and LIPCA-C2 actuator in order to confirm its validity. Finite element analysis considering thermal residual deformation showed that the bending behavior of piezoelectric composite actuator subjected to electric loads was significantly different according to the stacking sequence, thickness of constituent PZT ceramic and boundary conditions. In particular, the increase of thickness of PZT ceramic led to the increase of the bending stiffness of piezoelectric composite actuator but it did not always lead to the decrease of actuation distance according to the stacking sequences of piezoelectric composite actuator. Therefore, it is noted that the actuating performance of unimorph piezoelectric composite actuator is rather affected by bending stiffness than actuation distance.