• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.23-23
• /
• 2010

The $Bi_2Mg_{2/3}Nb_{4/3}O_7$ (BMNO)-Bi composite films sandwiched by an $Al_2O_3$ protection layer exhibited a linear increase of a dielectric constant with increasing thickness and the 1000nm-thick BMNO-Bi composite films showed a dielectric constant (~220) higher than that of its bulk material (~210), keeping a low leakage current density of about $0.1{\mu}A/cm^2$. An enhancement of the dielectric constant in the BMNO-Bi composite films was attributed to the hybrid model combined by a space charge polarization, dipolar response, and nano-capacitors. On the other hand, 1000nm-thick BMNO-Bi composite films sandwiched by 40nm-thick BMNO layer exhibited a dielectric constant of about 450 at 100 kHz and a leakage current density of $0.1{\mu}A/cm^2$ at 6V.

• The Korean Journal of Ceramics
• /
• v.5 no.2
• /
• pp.183-188
• /
• 1999

The crystallization behavior and electrical conductivity of the $CuO-Bi_2O_3-V_2O_5$ glasses with various CuO content were investigated. The glass formation regin was 0~20 mol% Bi2O3, 5~55 mol% CuO, and 30~90 mol% $V_2O_5$ with Tg=$275^{\circ}C$~$290^{\circ}C$. Among glasses with various compositions, the 31CuO-$14Bi_2O_3-55V_2O_5$ (mol%) glass heat-treated at $358^{\circ}C$ for 8 h showed the highest conductivity of ~ at room temperature. The heat-treated glasses increased in electrical conductivity by the order of 104 compared to non heat-treated glass. The linear relationship between 1n($\sigma$T)and $T^{-1}$ indicated that electrical conduction in the 31CuO-$14Bi_2O_3-55V_2O_5$ (mol%) glass occurred by a small polaron hopping.

• Proceedings of the Korean Institute of Intelligent Systems Conference
• /
• 1998.06a
• /
• pp.506-511
• /
• 1998

In this paper we consider multiobjective linear programming problems with coefficients of the objective functions specified by possibility distributions. Possibly and necessarily efficient solution sets are defined as funny solution sets whose membership grades represent possibility and necessity degrees to which a feasible solution is efficient. Considering efficiency condition and its dual condition in ordinary multiobjective linear programming problem, we propose efficiency test methods based on an extreme ray generation method. Since the proposed methods can be put in the part of a bi-section method, we can develop calculation and methods of the degree of possible and necessary efficiency for feasible solutions.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.05b
• /
• pp.279-282
• /
• 2000

We have been designed and fabricated a bi-directional ultrasonic linear motor using piezoelectric ceramics. With the finite element method, we design and verify validity of the structure, and determine its optimal structure, size of design variables, material and boundary conditions for proper generation of the ultrasonic waves. Based on the design, a prototype of the ultrasonic linear motor has been fabricated and characterized, which thereby proves practical applicability of this new motor.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.24 no.12
• /
• pp.969-976
• /
• 2011

In this study we aims to evaluate the effects of 1/3 mol% $Co_3O_4$ addition on the reaction, microstructure development, resultant electrical properties, and especially the bulk trap and grain boundary properties of $ZnO-Bi_2O_3-Sb_2O_3$ (Sb/Bi=2.0, 1.0, and 0.5) system (ZBS). The samples were prepared by conventional ceramic process, and characterized by XRD, density, SEM, I-V, impedance and modulus spectroscopy (IS & MS) measurement. In addition of $Co_3O_4$ in $ZnO-Bi_2O_3-Sb_2O_3$ (ZBSCo), the phase development, density, and microstructure were controlled by Sb/Bi ratio. Pyrochlore on cooling was reproduced in all systems. The more homogeneous microstructure was obtained in ZBSCo (Sb/Bi=1.0) system. In ZBSCo, the varistor characteristics were improved drastically (non-linear coefficient ${\alpha}$=23~50) compared to ZBS. Doping of $Co_3O_4$ to ZBS seemed to form $V^{\cdot}_o$(0.33 eV) as dominant defect. From IS & MS, especially the grain boundary of Sb/Bi=0.5 system is composed of electrically single barrier (0.93 eV) and somewhat sensitive to ambient oxygen with temperature.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2012.05a
• /
• pp.308-308
• /
• 2012

Electrodeposition of thermoelectric materials, including binary and ternary compounds, have been attracting attentions, because its many advantages including cost-effectiveness, rapid deposition rate, and ease of control their microstructure and crystallinity by adjusting electrodeposition parameters. In this work, $Bi_xTe_y$ films were potentiostatically electrodeposited using Au/Ni(80/20 nm)/Si substrate as the working electrode in solutions consisting of 10mM $TeO_2$ and 1M $HNO_3$ where $Bi(NO_3)_3$ was varied from 2.5 to 10 mM. Prior to electrodeposition potentiostatically, linear sweep voltammograms (LSV) were acquired with a standard three-electrode cell. The $Bi_xTe_y$ films deposited using the electrolyte containing low Bi ions shows p-type conductivity, which might be attributed by the large incorporation of Te phases. Near stoichiometric $Bi_2Te_3$ thin films were obtained from electrolytes containing 5mM $Bi(NO_3)_3$. This film shows the maximum Seebeck coefficient of $-100.3{\pm}12.7{\mu}V/K$. As the increase of Bi ions in electrolytes decreases the Seebeck coefficient and resistivity. The maximum power factor of $336.2{\mu}W/m{\cdot}K^2$ was obtained from the film deposited using the solution of 7.5mM $Bi(NO_3)_3$.

• Management Science and Financial Engineering
• /
• v.13 no.2
• /
• pp.1-27
• /
• 2007

This paper presents a fuzzy-goal programming(FGP) approach for Bi-Level Linear Multiple Objective Decision Making(BLL-MODM) problem in a large hierarchical decision making and planning organization. The proposed approach combines the attractive features of both fuzzy set theory and goal programming(GP) for MODM problem. The GP problem has been developed by fixing the weights and aspiration levels for generating pareto-optimal(satisfactory) solution at each level for BLL-MODM problem. The higher level decision maker(HLDM) provides the preferred values of decision vector under his control and bounds of his objective function to direct the lower level decision maker(LLDM) to search for his solution in the right direction. Illustrative numerical example is provided to demonstrate the proposed approach.

• The Journal of the Acoustical Society of Korea
• /
• v.18 no.8
• /
• pp.25-31
• /
• 1999

This paper describes design and fabrication of a new bi-directional ultrasonic linear motor working by means of a traveling wave. With the finite element method, we design and verify validity of the new structure, and determine its optimal structure, material, size, and boundary conditions for proper generation of the traveling wave. Based on the results, a prototype of the motor has been fabricated and characterized, which thereby proves practical applicability of the new structure.

• Proceedings of the KSR Conference
• /
• 2000.11a
• /
• pp.374-381
• /
• 2000

본 논문에서는 지진 발생시, LRB가 설치된 교량의 시간이력 해석을 수행하였다 이를 위해 LRB의 비선형 거동특성을 Bi-linear로 모형화 하였으며, 기존의 방법인 등가선형으로 모형화된 해석결과와 비교하였다. 또한 LRB받침만 설치된 경우와, LRB받침과 일반탄성받침이 함께 사용된 경우를 해석하여, 받침이 혼합된 경우, 상시하중과 지진하중시 발생할 수 있는 문제점을 검토하였다. 4경간 연속교량에 적용된 해석결과를 보면, LRB만을 설치한 경우, Pot-Bearing만 설치된 경우에 .비해, 고유주기 상승과 이력감쇠에 의한 지진력의 감소와 함께, 지진력의 효과적인 분배를 볼 수 있었으며, 일반탄성받침과의 적절한 조합에 의해서도, 충분한 면진성능을 얻을 수 있었다. 또한 LRB의 등가선형 모델이 Bi-linear 모델에 비해 보수적인 해석결과를 나타내었다.

• Computers and Concrete
• /
• v.15 no.2
• /
• pp.199-213
• /
• 2015

The residual fracture toughness of post-fire normal-strength concrete subjected up to $600^{\circ}C$ is considered by the wedge splitting test. The initial fracture toughness $K_I^{ini}$ and the critical fracture toughness $K_I^{un}$ could be calculated experimentally. Their difference is donated as the cohesive fracture toughness $K_I^c$ which is caused by the distribution of cohesive stress on the fracture process zone. A comparative study on determining the residual fracture toughness associated with three bi-linear functions of the cohesive stress distribution, i.e. Peterson's softening curve, CEB-FIP Model 1990 softening curve and Xu's softening curve, using an analytical method is presented. It shows that different softening curves have no significant influence on the fracture toughness. Meanwhile, comparisons between the experimental and the analytical calculated critical fracture toughness values further prove the validation of the double-K fracture model to the post-fire concrete specimens.