• Journal of Advanced Navigation Technology
• /
• v.15 no.2
• /
• pp.248-255
• /
• 2011

An investigation has been carried out, by computer simulation, to evaluate the impact of dispersion compensation configurations on 960 Gbps wavelength division multiplexed (WDM) system with optical phase conjugator (OPC). The considered dispersion compensation configurations in this research are conventional one-end type and bi-end type. One-end and bi-end type are made by using one dispersion compensating fiber (DCF) and two DCFs to decrease dispersion accumulated in one single mode fiber (SMF) span, respectively. It is found that bi-end compensation configuration offers the equal performance with that of one-end configuration in WDM system with residual dispersion per span (RDPS) of 400 ps/nm if net residual dispersion (NRD) had to be optimized in each cases.

• Journal of Advanced Navigation Technology
• /
• v.12 no.3
• /
• pp.201-207
• /
• 2008

Design rule of optical transmission link consisted of dispersion management (DM) controlling accumulated dispersion in total fiber length by precompensation and postcompensation, and optical phase conjugator (OPC) positioned at mid-way are proposed. DM schemes investigated in this paper are 2 types depending on the position of precompensation and postcompensation; bi-end type and concentration type. It is confirmed that effective residual dispersion ranges, as a design parameter of optical link, of transmission section from transmitter to OPC and transmission section from OPC to receiver are independence on the positions of dispersion compensating fiber (DCF) accomplishing precompensation and postcompensation, if both DCF position is symmetry with respect to OPC.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2009.09a
• /
• pp.884-890
• /
• 2009

The bi-directional pile load test with variable end plate overcomes the shortcoming of the Osterberg cell test. It is possible that the ultimate bearing capacity of the bi-direction can be known by using the loading of the end plate and two step procedures. The first step is to confirming end bearing capacity with variable end plate and the second step is similar to the conventional O-cell test. In the study, To calculate ultimate capacity of bi-directional load test using model with the pile with variable end plate O-cell, operated with end plate of 3 type on sand layer according to the relative density, loose, medium and dense conditions.

• Korean Journal of Microbiology
• /
• v.32 no.1
• /
• pp.91-95
• /
• 1994

EagBI is a type II restriction endonuclease from Enterobacter agglomerans strain CBNU45 isolated from soil. EagBI was partially purified by DEAE-cellulose, phosphocellulose P11 and hydroxylapatite column chromatography. EagBI recognizes and cleaves the sequence 5'-CGAT${\downarrow}$CG-3' and generates 2-base 3'-protruding cohesive ends. The optimal reaction conditions of EagBI are 10 mM Tris-HCl (pH 7.8), 6-10 mM $MgCl_2$, at 37 ${\circ}C$. The enzyme is maximally active in the absence of NaCl, able to cleave both $dam^-$ and $dam^+$ DNAs, and sensitive to heat treatment (at 65 ${\circ}C$ for 10 min). Therefore, although EagBI is an isoschizomer of PvuI, it is more useful than PvuI in respect of the NaCl requirement and heat-stability.

• Korean Journal of Materials Research
• /
• v.12 no.12
• /
• pp.911-917
• /
• 2002

0.5 at% $Na_2$Te-doped ($Pb_{0.7}Sn_{0.3}$)Te and ($Bi_{0.2}Sb_{0.8}$)$_2$$Te_3$ powders were fabricated by mechanical alloying process. 0.5 at% Na$_2$Te-doped ($Pb_{0.7}Sn_{0.3}$)Te powders were charged at one end of mold and ($Bi_{0.2}Sb_{0.8}$)$_2$$Te_3$ powders were charged at the other end of a mold. Then these powders were hot-pressed to form p-type ($Pb_{0.7}Sn_{0.3}$)Te/($Bi_{0.2}Sb_{0.8}$)$_2$$Te_3$ functional gradient materials with the segment ratios (the ratio of ($Pb_{0.7}Sn_{0.3}$)Te to ($Bi_{0.2}Sb_{0.8}$)$_2$$Te_3$ ) of 1:2, 1:1, and 2:1. Power generation characteristics of the ($Pb_{0.7}Sn_{0.3}$)Te/($Bi_{0.2}Sb_{0.8}$)$_2$$Te_3$ were measured. When the temperature difference ΔT at both ends of the specimen was larger than $300^{\circ}C$, the ($Pb_{0.7}Sn_{0.3}$)Te/($Bi_{0.2}Sb_{0.8}$)$_2$$Te_3$ with the segment ratios of 1:2 and 1:1 exhibited larger output power than those of the ($Bi_{0.2}Sb_{0.8}$)$_2$$Te_3$ and 0.5 at% $Na_2$ Te-doped ($Pb_{0.7}Sn_{0.3}$)Te alloys. The maximum output power of the ($Pb_{0.7}Sn_{0.3}$)Te/($Bi_{0.2}Sb_{0.8}$)$_2$$Te_3$ predicted with the measured Seebeck coefficient and the estimated electrical resistivity was in good agreement with the measured maximum output power.

• Textile Coloration and Finishing
• /
• v.30 no.2
• /
• pp.70-76
• /
• 2018

The dyeing behaviors of poly(ethylene terephthalate)(PET) bulky yarns, DTY(draw textured yarn) and SSY(latent crimped yarn), were investigated with different energy type disperse dyes compared with those of SDY(spin draw yarn). The maximum exhaustions of E-type disperse Red 60, Blue 56 and Yellow 54 on SSY were 99%, 94% and 93%, respectively. The maximum exhaustions of S-type disperse Red 179, Blue 79 and Orange 30 on SSY were 96%, 97% and 97%, respectively. The K/S values of SSY were significantly higher than those of DTY and SDY in all energy type of disperse dyes. The knit fabric composed of SSY became bulky at the end of high temperature dyeing process because of their thermal shrinkage property due to melt viscosity difference.

• Journal of information and communication convergence engineering
• /
• v.8 no.5
• /
• pp.489-492
• /
• 2010

This paper proposes the planar-type modified monopole antennas of loop structure. This antenna has an opened center of a conventional closed loop structure with an inside-folded terminal of the loop microstrip line. The size of the proposed antenna was minimized by folding the end of the loop. Also, the reactance value has been minimized by increasing capacitances between the coupled microstrip line. Therefore the proposed antenna has been compacted to about 20% from a conventional loop antenna and has increased its efficiency. The proposed antennas have an omni-directional pattern, the antenna gain was 3.67 [dBi] and the bandwidth was 900 MHz (2.6~3.56 GHz) with VSWR$\leq$2 from the simulated and the measured results. The frequency utilization coefficient was 29.9%. These properties could satisfy the S-DMB band.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2012.05a
• /
• pp.70-73
• /
• 2012

In this paper, we introduce a design method for a quasi-Yagi antenna (QYA) with broadband characteristics of an impedance bandwidth ratio of > 2 : 1 and a gain of > 4 dBi. The QYA is fed by a microstrip line fabricated on a coplanar strip line and it consists of 3 elements; a planar dipole, a nearby director close to the dipole, and a ground plane reflector. By placing a rectangular patch-type director with large width near to the dipole driver, broadband characteristics are achieved. An optimized 3-element QYA for operation over 1.6-3.5 GHz (bandwidth ratio 2.2 : 1) is fabricated on an FR4 substrate with a size of $90mm{\times}90mm$ and tested experimentally. The results show an impedance bandwidth of 1.56-3.74 GHz (bandwidth ratio 2.4 : 1) for VSWR < 2, a peak gain of 4.41-6.53 dBi, and a front-to-back ratio (FBR) > 13.6 dB within the bandwidth.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.21 no.5
• /
• pp.906-912
• /
• 2017

In this paper, we studied a design method for a broadband 3-element quasi-Yagi antenna (QYA) for indoor digital television (DTV) reception. The proposed QYA employs a novel balun between a microstrip (MS) line and a coplanar strip (CPS) line feeding the driver dipole. The proposed balun is constructed by connecting the end of MS line to CPS line through a shorting pin, and the CPS and ground reflector are connected through a circular ring-type conductor. An antenna, as an design example for the proposed antenna, is designed for the operation in the frequency band of 470-806 MHz for terrestrial DTV. The antenna fabricated on an FR4 substrate with a size of $270mm{\times}150mm$ showed a good performance such as a frequency band of 470-820 MHz for a voltage standing wave ratio < 2, a gain > 4.0 dBi, and a front-to-back ratio > 8.4 dB over the DTV frequency band.

• Proceedings of the KIPE Conference
• /
• 2011.07a
• /
• pp.429-430
• /
• 2011

This paper presents a simple and cost-effective stand-alone rapid battery charging system of 30kW for electric vehicles. The proposed system mainly consists of active front-end rectifier of neutral point clamped 3-level type and non-isolated bi-directional dc-dc converter of multi-phase interleaved half-bridge topology with coupled inductors. The charging system is designed to operate for both lithium-polymer and lithium-ion batteries. The complete charging sequence is made up of three sub-interval operating modes; pre-charging mode, constant-current mode, and constant-voltage mode. The pre-charging mode employs the staircase shaped current profile to accomplish shorter charging time while maintaining the reliable operation of the battery. The proposed system is able to reach the full-charge state within less than 16min for the battery capacity of 8kWh by supplying the charging current of 67A. The optimal discharging algorithm for Vehicle to the Grid (V2G) operation has been adopted to maintain the discharging current of 1C. Owing to the simple and compact power conversion scheme, the proposed solution has superior module-friendly mechanical structure which is absolutely required to realize flexible power expansion capability in a very high-current rapid charging system.