• Journal of the Korean Ceramic Society
• /
• v.36 no.5
• /
• pp.497-503
• /
• 1999

Recently regenerative burner system was developed and begins to be gradually used for better energy savings. Compared to conventional burner system the regenrative one has the several merits such as higher fuel efficiency light weigh of apparatus low harmful toxic gas and homogeneous heating zone etc. The regenerative material a very important component of the new regenerative burner system should possess the properties of low specific density higher surface area and high specific heat capacity. Ceramics is the best regenerative material because of stable mechanical properties even at high temperature and better thermal properties and excellent chemical stability. In this study alumina ball alumina tube 3-D ceramic foam and hoeycomb as regenerative materials were tested and evaluated. The computer silumation was conducted and compared to the result of field test. This paper is aimed to introduce a new application of ceramics at high temperature.

• The Journal of the Korea Contents Association
• /
• v.12 no.9
• /
• pp.250-256
• /
• 2012

Disease, such as osteopenia, osteoporosis, etc caused by reduced bone density are common to women after menopause and as the social medical cost increases due to osteoporosis fractures the medical interest in bone density reduction has increased. The bone density reduction is observed even for renal failure patients, due to their decreased ability to synthesize vitamin D which leads to bone fibrosis because of deficiency in calcium absorption. Thus renal failure patients not only suffer from kidney dysfunction, but also are exposed to complications, such as osteoporosis, due to reduced bone density. This research observed the change in bone density of patients receiving renal failure treatment and analyzed the change in bone density before and after kidney transplantations. Subjects were 214 renal failure patients at the department of nephrology Busan B General Hospital. The change in bone density was studied for subjects with and without kidney transplantation according to their age and sex. The research showed improvement or maintenance of bone density for subjects that received kidney transplantation, but showed a tendency of consistent decrease in bone density for subjects without kidney transplantation. Kidney transplantation can be considered as the best cure for renal failure patients, and this researched confirmed that bone density can be improved through kidney transplantation. Thus, this study can also be used as data for preventing complications due to renal failures.

• The Korean Journal of Malacology
• /
• v.30 no.1
• /
• pp.17-23
• /
• 2014

Ark shell Scapharca broughtonii length and total weight growth by density, which was hanging-cultured near the sea area of Yeosu-city, Hoenggan-island (below is Yeosu), showed inverse correlation with density. As for the average growth of shell length by density, the test area of 10 shells showed the best result as 5.21 mm, and it became lower as density became higher. Also, the increase of total weight by density showed the same result, thus on the whole, the increase of average shell length and total weight of 10-20 shell test area showed the better result than the test area of 30-40 shells. In addition, even if the parashell's shell length by density and total weight growth in the sea area of Namhae-gun, Mijo-fishing port (below is Namhae) showed inverse correlation with density, it showed the slighter inverse correlation than the sea area of Yeosu. As for the average growth of shell length by density, the test area of 10 shells showed the best result as 4.55mm, but the average growth of shell length by density in the test area of 20-40 shells appeared to be similar as 3.11, 3.36 and 3.27 mm. On the other hand, as for the increase of total weight by density, the test area of 10-20 shells showed the more increase than the test area of 30-40 shells. In conclusion, it is guessed that the culture density of 20 shells/$0.12m^2$ (166 shells / $1m^2$) would be appropriate when hanging-culturing the shells. At the sea area of A, the survival rate of Scapharca broughtonii parashell was 68-87% by density respectively, and it showed the density-dependent result, while the survival rate of sea area of Namhae, where phytoplankton as prey is abundant, showed the much better result as 91-100%. It is guessed that this may be due to the fact that the quantity of phytoplankton in sea area of Yeosu is just 55.89% of sea area of Namhae. When hanging-culturing the shells, the water temperature by sea area ranged from 16.22 to $25.66^{\circ}C$, salinity 30.07-33.48, pH 8.10-8.45, and DO 4.49-9.65 mg/L.

• Journal of Broadcast Engineering
• /
• v.25 no.1
• /
• pp.36-47
• /
• 2020

The improved belief-propagation-based algorithms, such as normalized min-sum algorithm (NMSA) or offset min-sum algorithm (OMSA), are widely used to decode LDPC(Low-Density Parity-Check) codes because they are less computationally complex and work well even at low SNR(Signal-to-Noise Ratio). However, these algorithms work well only when an appropriate normalization factor or offset value is used. A new method that uses a CMD(Check Node Message Distribution) chart and least-square method, which has been recently proposed, has advantages on computational complexity over other approaches to get optimal coefficients. Furthermore, this method can be used to derive coefficients for each iteration. In this paper, we apply this method and propose an algorithm to derive a combination of normalization factor and offset value for a combined normalized and offset min-sum algorithm to further improve the decoding of LDPC codes. Simulations on the next-generation broadcasting standards, ATSC 3.0 LDPC codes, prove that a combined normalized and offset min-sum algorithm which takes the proposed coefficients as correction coefficients shows the best BER performance among other decoding algorithms.

• Journal of Science Education
• /
• v.37 no.1
• /
• pp.221-232
• /
• 2013

The purpose of this study was to examine the effect of the CoRe-based density unit class on conceptual formation and on learner satisfaction with the class. For this study, two hundred and forty 8th grade students were chosen from six classes. The students were divided into two groups: an experimental group, which received a CoRe-based density unit lesson, and a control group, which was taught based on traditional teaching method. The CoRe-based density unit classes consisted of 4 periods based on the analysis of the previous studies on CoRe about density. The results showed the meaningful significant difference between the CoRe-based classes and the classes based on traditional teaching method both in the posttest on the extent of the conceptual formation on the density and in the retention test. The difference suggests that the lesson with CoRe is based on the consideration of the difficulties and limitations students face in various fields such as the students themselves, teachers, learning environment, evaluation, etc. during their learning process and even in the types of preconception they have, and the CoRe-based lesson is centered around the best teaching strategies to solve such difficulties. As a result of the analysis on the experimental group's class satisfaction, it is revealed that the students with a high level of attitudes related science or with a high level of science achievement showed especially high satisfaction in their learning. Analysis of questionnaire survey showed that the students in the experimental group got the opportunity through CoRe-based lesson to stretch their thoughts and ideas in a free way and preferred a teaching method which didn't just show the concept, but allowed them to find it for themselves or which let them predict the solution and then confirm the result on their own and a lesson which encouraged their active participation.

• ALGAE
• /
• v.22 no.3
• /
• pp.241-246
• /
• 2007

Cochtodinium votykrikoides -related red tide is the most notorious tidal bloom, resulting in mass mortality to marineanimals. This study aimed to test the effect of C. polyknkoides on the lethality to Haliotis discus hannai under con-trolled conditions. The oxygen demand of C. polykrikoides increases to reach its peak duhng the night, while the oxy-gen usage by H. discus hannai was continuously decreased with a threshold of 2 mg L U. The addition of C.polykrikoides did not effect the respiration of the H. discus hannai. However, the usage of oxygen by C. polykrikoidesduhng the night may lead to anoxia in the animal. With aeration, the level of dissolved oxygen (D.O.) was between6.06 and 7.28 mg LU; 90% of abalones survived even with a high concentration of C. potykrikoides (9000 cells mL U).Without aeration (3 mg LU of D.O.), however, the H. discus hannai suffocated immediately. Once 20 hours hadelapsed, all of the abalones were dead. The density of the H. discus hannai population contributed to their mortality.Therefore, aeration during the night and maintaining lower abalone densities is the best way to promote the sur-vivorship of H. discus hannai during a C. polykrikoides red tide.

• International Journal of Advanced Culture Technology
• /
• v.8 no.2
• /
• pp.252-259
• /
• 2020

Wheatgrass is a type of young grass that contains a lot of vitamins, minerals, and protein even compared to grain products produced from its mature cereal plants. In the context of product development and increasing product sales value, a study on the use of wheatgrass extract as an ingredient of fermented beverage was conducted. In this study wheatgrass used was self-grown using a tray in the Laboratory. The variation of wheatgrass extracts used was obtained from the twin-gear type extractor, slow-squeeze type extractor, and chopped wheatgrass. In the extraction process, the performances of the process: density, extract yield, processing capacity, and the rate of production, were analyzed. For another analysis, the physicochemical properties both of wheatgrass extracts and fermented beverages were also analyzed. The physicochemical properties analyzed included TSS, pH, acidity, and others content. The results of extraction performance analysis and physicochemical characteristics of wheatgrass extract planted at 10-20℃ based on this research gave the best results using the twin-gear extractor. The twin-gear type of extractor used in this study. All of these results were also in accordance with the statistical analysis conducted in this study.

• Nuclear Engineering and Technology
• /
• v.54 no.9
• /
• pp.3459-3469
• /
• 2022

Matrix composites of n-WO₃/n-Bi₂O₃/PVA with different loadings of n-WO₃/n-Bi₂O₃ mixtures (0-15 wt%) and starch (0 and 3 wt%) were fabricated by using melt-mixing method. The X-ray attenuation capability were evaluated based on mass attenuation coefficient (μ/⍴) using a general diagnostic X-ray machine at 40-100 kVp. The effect of starch addition on the dispersion of the fillers in the PVA matrix were observed by using FESEM through morphological analysis. The fabricated samples have shrunken and caused their thickness to be decreased (0.35 mm-0.55 mm) after the drying process even though fixed thickness (2.0 mm) was set initially. The density and HVL values of the samples with 3 wt% starch was seen lower than samples without starch (0 wt%), however the former have provided improvement in filler dispersion and better X-ray attenuation capability compared to the latter. As conclusion, the matrix composite of n-WO₃/n-Bi₂O₃/PVA with 15 wt% of n-Bi₂O₃, 8 wt% of n-WO₃ and 3 wt% starch can be selected as the best promising candidate for X-ray shielding materials.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.38 no.6
• /
• pp.655-661
• /
• 2020

SGM (Semi Global Matching) can be used to find all the conjugate points between stereo images. Therefore, it enables high-density DSM (Digital Surface Model) production from high-resolution satellite images. However, water, shadows, and occlusion areas cause mismatching of the surrounding points in this method. Particularly, in buildings with large-parallax and elongated-shapes such as a Korean style apartment, it is difficult to reconstruct the 3D building even if the SGM method is applied to a high-resolution 50cm satellite image. This study proposed and performed the SGM technique with a classified image and an edge image from the IKONOS-2 satellite stereo-image with a 1m resolution to produce DSM. It was compared with the DSMs from the general SGM and the high-density ABM (Area Based Matching) matching of ERDAS software. The results of the apartment DSM by the proposed method were the best in the test area. As a result, despite the image having a resolution of 1m, the outline of the building DSM could be expressed more clearly than the existing method.

• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 2000.06a
• /
• pp.16-23
• /
• 2000

The increasing functional needs of top-quality printing papers and packaging paperboards, and especially the rapid developments in electronic printing processes and various computer printers during past few years, set new targets and requirements for modern paper quality. Most of these paper grades of today have relatively high filler content, are moderately or heavily calendered , and have many coating layers for the best appearance and performance. In practice, this means that many of the traditional quality assurance methods, mostly designed to measure papers made of pure. native pulp only, can not reliably (or at all) be used to analyze or rank the quality of modern papers. Hence, introduction of new measurement techniques is necessary to assure and further develop the paper quality today and in the future. Paper formation , i.e. small scale (millimeter scale) variation of basis weight, is the most important quality parameter of paper-making due to its influence on practically all the other quality properties of paper. The ideal paper would be completely uniform so that the basis weight of each small point (area) measured would be the same. In practice, of course, this is not possible because there always exists relatively large local variations in paper. However, these small scale basis weight variations are the major reason for many other quality problems, including calender blacking uneven coating result, uneven printing result, etc. The traditionally used visual inspection or optical measurement of the paper does not give us a reliable understanding of the material variations in the paper because in modern paper making process the optical behavior of paper is strongly affected by using e.g. fillers, dye or coating colors. Futhermore, the opacity (optical density) of the paper is changed at different process stages like wet pressing and calendering. The greatest advantage of using beta transmission method to measure paper formation is that it can be very reliably calibrated to measure true basis weight variation of all kinds of paper and board, independently on sample basis weight or paper grade. This gives us the possibility to measure, compare and judge papers made of different raw materials, different color, or even to measure heavily calendered, coated or printed papers. Scientific research of paper physics has shown that the orientation of the top layer (paper surface) fibers of the sheet paly the key role in paper curling and cockling , causing the typical practical problems (paper jam) with modern fax and copy machines, electronic printing , etc. On the other hand, the fiber orientation at the surface and middle layer of the sheet controls the bending stiffness of paperboard . Therefore, a reliable measurement of paper surface fiber orientation gives us a magnificent tool to investigate and predict paper curling and coclking tendency, and provides the necessary information to finetune, the manufacturing process for optimum quality. many papers, especially heavily calendered and coated grades, do resist liquid and gas penetration very much, bing beyond the measurement range of the traditional instruments or resulting invonveniently long measuring time per sample . The increased surface hardness and use of filler minerals and mechanical pulp make a reliable, nonleaking sample contact to the measurement head a challenge of its own. Paper surface coating causes, as expected, a layer which has completely different permeability characteristics compared to the other layer of the sheet. The latest developments in sensor technologies have made it possible to reliably measure gas flow in well controlled conditions, allowing us to investigate the gas penetration of open structures, such as cigarette paper, tissue or sack paper, and in the low permeability range analyze even fully greaseproof papers, silicon papers, heavily coated papers and boards or even detect defects in barrier coatings ! Even nitrogen or helium may be used as the gas, giving us completely new possibilities to rank the products or to find correlation to critical process or converting parameters. All the modern paper machines include many on-line measuring instruments which are used to give the necessary information for automatic process control systems. hence, the reliability of this information obtained from different sensors is vital for good optimizing and process stability. If any of these on-line sensors do not operate perfectly ass planned (having even small measurement error or malfunction ), the process control will set the machine to operate away from the optimum , resulting loss of profit or eventual problems in quality or runnability. To assure optimum operation of the paper machines, a novel quality assurance policy for the on-line measurements has been developed, including control procedures utilizing traceable, accredited standards for the best reliability and performance.