• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2005.05a
• /
• pp.130-133
• /
• 2005

Efficient finite element method has been introduced for metallic sandwich plates subject to 3-point bending. A full model 3-point bending FE-analysis shows that plastic behavior of inner structures appears only at the load point. So, Unit structures of sandwich plates are defined to numerically calculate the bending stiffness with recurrent boundary condition of pure bending. And then equivalent models with same bending stiffness and strength of full models are designed analytically. It is demonstrated that results of both models are almost same and FE analysis method with equivalent models can reduce analysis time effectively.

• Journal of Korean Association for Spatial Structures
• /
• v.20 no.4
• /
• pp.141-147
• /
• 2020

Single-layered grid space steel roof structure is an architectural system in which the structural ability of the nodal connection system greatly influences the stability of the entire structure. Many bolt connection systems have been suggested to enhance for better construct ability, but the structural behavior and maximum resistance of the connection system according to the size of bolt clearance play were difficult to identify. In particular, the identification of bending stiffness of the connection system is very important due to the characteristics of shell structures in which membrane stresses based on bending force effect significantly. To identify effective structural behavior and maximum bearing force, four representative nodal connection systems were selected and nonlinear numerical analysis were performed. The numerical analysis considering the size of the bolt clearance were performed to investigate structural behavior and maximum values of the bending force. In addition, the type of effective nodal connection system were evaluated. As a result, the connection system, which has two shear plane, represented high bending stiffness.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2001.11a
• /
• pp.853-858
• /
• 2001

The PSC bridge being built by ILM may have greater bending moment during its construction rather than after completion. When it occurs, Engineer should suggest to reduce stress-resultants than to make bigger cross-section with considering stability ,economics, and proper span-to-depth ratio. The used method is to install extruded nose at the end of girder. It substitutes the weighted segment for the light. From the reference, the stiffness of extruded nose, is 1/10 of the main girder, and the length is 60 to 70% of the length of the span, with little justification. In this study, the proper length and stiffness of the nose element is determined by the parametric study and idealizing procedure. The results about the extruded nose through the mixing of the parameter of its stiffness and length, the proper length of extruded nose is 80% of the longest span and the proper stiffenss is 13% of the bending stiffness of the superstructure and the proper length of extruded nose is 70% of the longest span and the proper stiffness is 9.5% of the bending stiffness of the superstructure.

• Steel and Composite Structures
• /
• v.33 no.5
• /
• pp.681-697
• /
• 2019

This paper numerically assesses the initial stiffness and moment capacity of stainless steel composite bolted joints with concrete-filled circular tubular (CFCT) columns. By comparing with existing design codes including EN 1993-1-8 and AS/NZS 2327, a modified component method was proposed to better predict the flexural performance of joints involving circular columns and curved endplates. The modification was verified with independent experimental results. A wide range of finite element models were then developed to investigate the elastic deformations of column face in bending which contribute to the corresponding stiffness coefficient. A new design formula defining the stiffness coefficient of circular column face in bending was proposed through regression analysis. Results suggest that a factor for the stiffness coefficient of endplate in bending should be reduced to 0.68, and more contribution of prying forces needs to be considered. The modified component method and proposed formula are able to estimate the structural behaviour with reasonable accuracy. They are expected to be incorporated into the current design provisions as supplementary for beam-to-CFCT column joints.

• Structural Engineering and Mechanics
• /
• v.76 no.3
• /
• pp.293-310
• /
• 2020

This study derives the differential equations of free vertical bending and torsional vibrations for two- and three-pylon suspension bridges using d'Alembert's principle. The respective algorithms for natural vibration frequency and vibration mode are established through the separation of variables. In the case of the three-pylon suspension bridge, the effect of the along-bridge bending vibration of the middle pylon on the vertical bending vibration of the entire bridge is considered. The impact of torsional vibration of the middle pylon about the vertical axis on the torsional vibration of the entire bridge is also analyzed in detail. The feasibility of the proposed method is verified by two engineering examples. A comparative analysis of the results obtained via the proposed and more intricate finite element methods confirmed the former feasibility. Finally, the middle pylon stiffness effect on the vibration frequency of the three-pylon suspension bridge is discussed. It is found that the vibration frequencies of the first- and third-order vertical bending and torsional modes both increase with the middle pylon stiffness. However, the increase amplitudes of third-order bending and torsional modes are relatively small with the middle pylon stiffness increase. Moreover, the second-order bending and torsional frequencies do not change with the middle pylon stiffness.

• Composites Research
• /
• v.32 no.4
• /
• pp.191-198
• /
• 2019

The basic mechanical properties of helicopter rotor blade are important parameters for the analysis of helicopter performance. However, it is difficult to estimate these properties because the most of rotor blades consist of various materials such as composite materials and metals, etc. In this paper, the bending/torsional stiffness for composite rotor blade of unmanned helicopter were evaluated through experimental and analytical studies. In finite element analysis, the bending/torsional stiffness were evaluated through the relationship of load-displacement and element stiffness matrix. The evaluated stiffness from the measured strains and displacements in bending and torsional test agreed well with the derived results of FEA.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.8 no.2
• /
• pp.47-57
• /
• 1984

Effect on the hand value and mechanical properties of blend ratio and weight had been investigated Oil summer suits for men. Relation between the mechanical properties and the deformation in behavior was also studied. The mechanical properties which influence the hand values and total hand value had been discussed and the relation between mechanical properties, hand values and fabric count had, too. As result, the following conclusions had been obtained. 1) The values of tensile properties increased with the increase of blend ratio of wool. The values of surface properties increased according to the increase of blend ratio of polyester. 2HB(bending properties) of polyester/wool blend showed higher value than that of $100\%$ wool, but there was no change in the shearing properties according to the blend ratio. The values of stiffness, crispness and anti-drape stiffness of blend fabric showed higher values than those of $100\%$ wool fabric. The value of fullness (including softness) of blend fabric showed lower value than that of $100\%$ wool fabric. 2) The correlation between hand values and mechanical properties showed following order. in stiffness : bending properties>surface properties in crispness: surface properties>bending properties in anti-drape stiffness: bending properties>surface properties>shearing properties.

• Structural Engineering and Mechanics
• /
• v.20 no.3
• /
• pp.363-380
• /
• 2005

The cable tension plays an important role in the construction, assessment and long-term health monitoring of cable structures. The cable vibration equation is nonlinear if cable sag and bending stiffness are included. The engineering implementation of a vibration-based cable tension evaluation is mostly carried out by the simple taut string theory. However, the simple theory may cause unacceptable errors in many applications since the cable sag and bending stiffness are ignored. From the practical point of view, it is necessary to have empirical formulas if they are simple and yet accurate. Based on the solutions by means of energy method and fitting the exact solutions of cable vibration equations where the cable sag and bending stiffness are respectively taken into account, the empirical formulas are proposed in the paper to estimate cable tension based on the cable fundamental frequency only. The applicability of the proposed formulas is verified by comparing the results with those reported in the literatures and with the experimental results carried out on the stay cables in the laboratory. The proposed formulas are straightforward and they are convenient for practical engineers to fast estimate the cable tension by the cable fundamental frequency.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2008.03a
• /
• pp.1406-1416
• /
• 2008

Soil nailing is used as a method of slope stabilization and excavation support. The design method of soil nail are based on experience or assumption of interaction between soil and reinforcement. Most design methods simply considers the tension of reinforcement for analysis of slope stabilization. Soil nails interact with soils under combined loading of shear and tension. Jewell & Pedley(1990) suggested a design equation of shear force with bending stiffness and discussed that the magnitude of the maximum shear force is small in comparison with the maximum axal force. However, they have used a very conservative limiting bearing stress on nails. This paper discusses that the shear strength of soil nails should not be disregarded with proper bearing stresses on nails. The modified FHWA design method was proposed by considering shear forces on nails with bending stiffness.

• Tribology and Lubricants
• /
• v.34 no.1
• /
• pp.23-32
• /
• 2018

Coupling is a mechanical component that transmits rotational force by connecting two shafts. Curvic coupling is widely used in high-performance systems because of its excellent power transmission efficiency and easy machining. However, coupling applications change dynamic behavior by reducing the stiffness of an entire system. Contact surface stiffness is an important parameter that determines the dynamic behavior of a system. In addition, the roughness profile of a contact surface is the most important parameter for obtaining contact stiffness. In this study, we theoretically establish the process of contact and bending stiffness analysis by considering the rough surface contact at Curvic coupling. Surface roughness parameters are obtained from Nayak's random process, and the normal contact stiffness of a contact surface is calculated using the Greenwood and Williamson model in the elastic region and the Jackson and Green model in the elastic-plastic region. The shape of the Curvic coupling contact surface is obtained by modeling a machined shape through an actual machining tool. Based on this modeling, we find the maximum number of gear teeth that can be machined according to the contact angle. Curvic coupling stiffness is calculated by considering the contact angle, and the calculation process is divided into stick and slip conditions. Based on this process, we investigate the stiffness characteristics according to the contact angle.