• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2010년도 춘계 학술대회 제22권1호
• /
• pp.243-244
• /
• 2010

철근콘크리트 보의 휨 보강을 위하여 활용되는 재료는 매우 다양하다. FRP의 경우 우수한 무게-강성비 및 시공성을 바탕으로 최근 활발히 활용되어지고 있다. 그러나 이들 FRP 휨 보강재의 활용에 있어 취성적 재료특성은 실제 현장적용에 있어 콘크리트 박리파괴 유발 및 단부 부착파괴의 주요 원인으로 고려되어지고 있다. 따라서 본 연구에서는 이들 FRP 휨 보강재의 연성적 거동을 개선하기위하여 복합재료 구성요소 중 Fiber의 적층면적 중 일부분을 알루미늄 재료로 대체하여 휨 보강재로서의 구조적 성능을 조사하였다. 연성보강 fiber로는 얇은 두께의 알루미늄이 고려되었으며 다양한 배합설계 조건이 본 연구에서 수행되었다. 최종적으로 알루미늄 삽입 보강재 제작에 따른 연성개선 및 에너지 저장효과에 대한 결과들을 실험을 통하여 연구하였다.

• Structural Monitoring and Maintenance
• /
• 제9권3호
• /
• pp.271-287
• /
• 2022

This study investigates the bending behavior of a composite concrete slab roof with different methods of externally strengthing using steel plates and carbon fiber reinforced polymer (CFRP) strips. First, the concrete slab model which was reinforced with CFRP strips on the bottom surface of it is validated using experimental data, and then, using numerical modeling, 7 different models of square-shaped composite slab roofs are developed in ABAQUS software using the finite element modeling. Developed models include steel rebar reinforced concrete slab with variable thickness of CFRP and steel plates. Considering the control sample which has no external reinforcement, a set of 8 different reinforcement states has been investigated. Each of these 8 states is examined with 6 different uncertainties in terms of the properties of the materials in the construction of concrete slabs, which make 48 numerical models. In all models loading process is continued until complete failure occurs. The results from numerical investigations showed using the steel plates as an executive method for strengthening, the bending capacity of reinforced concrete slabs is increased in the ultimate bearing capacity of the slab by about 1.69 to 2.48 times. Also using CFRP strips, the increases in ultimate bearing capacity of the slab were about 1.61 to 2.36 times in different models with different material uncertainties.

• Structural Engineering and Mechanics
• /
• 제16권4호
• /
• pp.469-478
• /
• 2003

The primary aim of this study was to investigate the bond strength between reinforcement and concrete. Large sized nine beams, which were produced from concrete with approximately ${f_c}^{\prime}=30$ MPa, were tested. Each beam was designed to include two bars in tension, spliced at the center of the span. The splice length was selected so that bars would fail in bond, splitting the concrete cover in the splice region, before reaching the yield point. In all experiments, the variable used was the reinforcing bar diameter. In the experiments, beam specimens were loaded in positive bending with the splice in a constant moment region. In consequence, as the bar diameter increased, bond strength and ductility reduced but, however, the stiffnesses of the beams (resistance to deflection) increased. Morever, a empirical equation was obtained to calculate the bond strength of reinforcement and this equation was compared with Orangun et al. (1977) and Esfahani and Rangan (1998). There was a good agreement between the values computed from the predictive equation and those computed from equations of Orangun et al. (1977) and Esfahani and Rangan (1998).

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집A
• /
• pp.842-847
• /
• 2001

In order to reinforce the plate in bending spot-welding method is usually used. To analyze the effect of the reinforcement of the plates spot-welded, finite element method was employed to take advantage of the deflection obtained with respect to the change of the aspect ratio and area ratio. The reinforcement effect represented by the equivalent thickness. Was maximum when the aspect ratio was around $1.2{\sim}1.6$ and the area ratio was 0.05.

• 한국농공학회:학술대회논문집
• /
• 한국농공학회 2000년도 학술발표회 발표논문집
• /
• pp.284-289
• /
• 2000

This study is performed to evaluate an the crack properties and repair-reinforcement of concrete introduced crack. Materials used are portland cement, coarse aggregate, fine aggregate, unsaturated polyester resin and fly ash. Specimen is used beam of 76${\times}$76${\times}$412mm for measurement of pulse velocity, dynamic modulus of elasticity and bending strength and is introduced crack artificially. The following conclusions are drawn; Pulse velocity, dynamic modulus of elasticity and bending strength of concrete introduced crack is shown the lower 1.24∼11.91%, 3.42∼17.21% and 38.17∼61.0% than that of the control concrete, respectively. Pulse velocity, dynamic modulus of elasticity and bending strength of concrete repaired and reinforced crack is shown the higher 0.5∼2.60%, 1.57∼3.07% and 28.17∼47.25% than that of the concrete introduced crack and the lower than that of the control concrete, respectively.

• 콘크리트학회논문집
• /
• 제16권4호
• /
• pp.493-500
• /
• 2004

FREP(Fiber Reinforced Epoxy Panel)는 고인장강도, 경량성, 내부식성 및 시공성 등의 우수한 성질을 가지고 있어 손상된 RC보의 보강에 이용되고 있다. 본 연구에서는 RE보에 대한 사용 전 휨보강의 경우와 사용 중 휨보강의 경우에 대한 구성방정식을 정립하여 그 차이를 규명하고, 보강재 단부의 응력집중으로 인해 발생하는 단부박리파괴(rip-off failure)의 역학적 특성을 밝힘으로써 휨보강 효과 성능을 평가하였다. 연구결과 FREP로 휨보강된 철근콘크리트 보의 지배적인 파괴모드는 단부박리파괴이며, 본 연구의 실험 및 해석조건을 기준으로 RC 보강보의 단부박리파괴에 대한 평가를 실시한 결과 FREP 보강두께의 과다로 인한 보강단부의 급격한 휨강성의 변화로 응력집중 현상이 발생하여 단부박리파괴가 생긴다는 것을 알 수 있었다. 이는 보강 설계 시 단부박리파괴에 대한 평가가 반드시 필요한 것을 의미한다. 또한 FREP의 보강시기에 따른 보강효과를 분석한 결과 사용 전 보강(I-Type)에 비해 사용 중 보강(P-Type)의 보강효과가 감소하는 것으로 나타났다. 따라서, 기존 구조물과 같이 사용 중인 구조물을 보강하는 경우에는 이미 작용하고 있는 보강전하중(응력)으로 인한 발생 응력을 보강설계 시 고려하여야 할 것으로 판단된다.

• Structural Engineering and Mechanics
• /
• 제48권6호
• /
• pp.833-848
• /
• 2013

Nine rectangular-section of High Strength Concrete(HSC) beams were designed and casted based on the American Concrete Institute (ACI) code provisons with varying of tensile reinforcement ratio as (${\rho}_{min}$, $0.2_{{\rho}b}$, $0.3_{{\rho}b}$, $0.4_{{\rho}b}$, $0.5_{{\rho}b}$, $0.75_{{\rho}b}$, $0.85_{{\rho}b}$, $_{{\rho}b}$, $1.2_{{\rho}b}$). Steel and concrete strains and deflections were measured at different points of the beam's length for every incremental load up to failure. The ductility ratios were calculated and the moment-curvature and load-deflection curves were drawn. The results showed that the ductility ratio reduced to less than 2 when the tensile reinforcement ratio increased to $0.5_{{\rho}b}$. Comparison of the theoretical ductility coefficient from CSA94, NZS95 and ACI with the experimental ones shows that the three mentioned codes exhibit conservative values for low reinforced HSC beams. For over-reinforced HSC beams, only the CSA94 provision is more valid. ACI bending provision is 10 percent conservative for assessing of ultimate bending moment in low-reinforced HSC section while its results are valid for over-reinforced HSC sections. The ACI code provision is non-conservative for the modulus of rupture and needs to be reviewed.

• 한국기계가공학회지
• /
• 제8권2호
• /
• pp.60-68
• /
• 2009

The objective of this paper is to design stamping die of inner reinforcement panel with DL 950 advanced high strength steel as stamping materials through numerical analyses and experiments. The stamping process was designed as bending dominant process consisting of 1 step of notching and 4 steps of bending processes. In order to obtain a proper design of the stamping die, various three-dimensional elasto-plastic finite element analyses were performed using a commercial code AUTOFORM V4.2. Design parameter of stamping die was chosen as the corner radius of the stamping die for each step. From the results of the FE analysis, feasible corner radii of the stamping die, which can minimize the deviation of corner angle of the stamped part from design data, and forming load for each part were estimated. Stamping experiments were carried out using the manufactured stamping die according to the proposed die design. The results of experiments were shown that the stamping die can successfully manufacture the inner reinforcement panel with DL 950 advanced high strength steel as base stamping material.

• Structural Engineering and Mechanics
• /
• 제63권5호
• /
• pp.575-583
• /
• 2017

The study covers the behavior of reinforced concrete deep beams loaded under 4-point bending, failed by shear and repaired using bonding glass fiber reinforced plastics fabrics (GFRP) patches. Two rehabilitation methods have been used to highlight the influence of the composite on the ultimate strength of the beams and their failure modes. In the first series of trials the work has been focused on the reinforcement/rehabilitation of the beam by following the continuous configuration of the FRP fabric. The patch with a U-shape did not provide satisfactory results because this reinforcement strategy does not allow to increase the ultimate strength or to avoid the abrupt shear failure mode. A second methodology of rehabilitation/reinforcement has been developed in the form of SCR (Strips of Critical Region), in which the composite materials reinforcements are positioned to band the inclined cracks (shear) caused by the shear force. The results obtained by using this method lead a superior out come in terms of ultimate strength and change of the failure mode from abrupt shearing to ductile bending.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2008년도 춘계 학술발표회 초청강연 및 논문집
• /
• pp.1406-1416
• /
• 2008

Soil nailing is used as a method of slope stabilization and excavation support. The design method of soil nail are based on experience or assumption of interaction between soil and reinforcement. Most design methods simply considers the tension of reinforcement for analysis of slope stabilization. Soil nails interact with soils under combined loading of shear and tension. Jewell & Pedley(1990) suggested a design equation of shear force with bending stiffness and discussed that the magnitude of the maximum shear force is small in comparison with the maximum axal force. However, they have used a very conservative limiting bearing stress on nails. This paper discusses that the shear strength of soil nails should not be disregarded with proper bearing stresses on nails. The modified FHWA design method was proposed by considering shear forces on nails with bending stiffness.