• Journal of Pharmaceutical Investigation
• /
• 제35권6호
• /
• pp.411-416
• /
• 2005

The aim of the present work was to prepare the nanosuspension of inorganic pigment which shows light reflection and scattering as efficient sunscreen. The zinc oxide (ZnO) was chosen as an inorganic pigment, and high pressure homogenizer and bead mill have been used for the preparation of nanosuspension. The ZnO nanosuspensions were characterized by particle size, in vitro sun protection factor (SPF) and UV transmittance. ZnO nanosuspension prepared by bead mill showed the average diameter of $119{\pm}4\;nm$, resulting in the high value of SPF $(28.74{\pm}2.06,\;n=20)$, while that prepared by high pressure homogenizer showed the average diameter of $751{\pm}32\;nm$ with the relative lower value of SPF $(21.38{\pm}1.94\;n=20)$. In addition, the film of ZnO nanosuspension prepared by bead mill was showed a high visible ray (VIS) transmittance, indicating a high transparency. In conclusion, a physically stable ZnO nanosuspension in cyclomethicone was successfully prepared using bead mill for the suitable sunscreen preparations.

• Biotechnology and Bioprocess Engineering:BBE
• /
• 제10권3호
• /
• pp.284-288
• /
• 2005

Baker's yeast was disrupted in a 1.4-L stainless steel horizontal bead mill under a continuous recycle mode using 0.3 mm diameter zirconia beads as abrasive. A single pass in continuous mode bead mill operation liberates half of the maximally released protein. The maximum total protein release can only be achieved after passaging the cells 5 times through the disruption chamber. The degree of cell disruption was increased with the increase in feeding rate, but the total protein release was highest at the middle range of feeding rate (45 L/h). The total protein release was increased with an increase in biomass concentration from 10 to $50\%$(w/v). However, higher heat dissipation as a result of high viscosity of concentrated biomass led to the denaturation of labile protein such as glucose 6-phosphate dehydrogenase (G6PDH). As a result the highest specific activity of G6PDH was achieved at biomass concentration of $20\%$(ww/v). Generally, the degree of cell disruption and total protein released were increased with an increase in impeller tip speed, but the specific activity of G6PDH was decreased substantially at higher impeller tip speed (14 m/s). Both the degree of cell disruption and total protein release increased, as the bead loading increased from 75 to $85\% (v/v)$. Hence, in order to obtain a higher yield of labile protein such as G6PDH, the yeast cell should not be disrupted at biomass concentration and impeller tip speed higher than $20\%(w/v)$ and 10 m/s, respectively.

• 상하수도학회지
• /
• 제22권5호
• /
• pp.505-510
• /
• 2008

Excess sludge and raw sludge were treated by ball mill in order to promote solubilization, and it was known that the level of solubilization was higher in excess sludge rather than raw sludge. About solid concentration, with the increase of TS, the amounts of solubilization was increased. And excess sludge was solubilized more effectively with the increase of ball mill treatment time. Especially, in case of excess sludge, within 5 min of ball mill treatment, 6 times of solubilization was achieved compared with raw sludge. The effect of bead size was also tested and 1 mm bead was most desirable when applied to the TS 4% of excess sludge. Particle size decrease by the ball mill treatment was more effective in raw sludge, nevertheless the level of solubilization was always higher in excess sludge. This means that the results of particle analysis could not be understood as a indicator for sludge solubilization. Generally, excess sludge and raw sludge are mixed at the thicker in the STP, but considering a ball mill pretreatment as an alternative for sludge solubilization, it is desirable to treat not raw sludge but excess sludge alone in the aspect of solubilization yield and economical process.

• 산업기술연구
• /
• 제25권B호
• /
• pp.127-133
• /
• 2005

Manufacturing methods of Nano particles can be distinguished by top-down technology as physical method and bottom-up technology as chemical synthetic method. Top-down technology is a kind of method for making microstructure as like carving after forming a macroscopic structure in advance and its typical methods are ball milling, gas condensation method and so on. Nano Particles synthesized by bottom-up method have got to do dispersing process for using them as actual nano particles because their viscosity are very strong and so easy to shape cohesive substances. Therefore, this study is about a particle separating device which separates a certain constant size of grains processed already in mill and mixer because we mostly use media agitating mill as a device of milling and dispersing and we necessarily use very slight balls as media for manufacturing nano particles in the machine. The centrifugal device has been designed for passing and separating below a certain type of grain size after final process of particles in the mill.

• 한국재료학회지
• /
• 제26권3호
• /
• pp.136-142
• /
• 2016

To study the dispersion factors of silica sol prepared from fumed silica powder, we prepared silica sol under an aqueous system using a batch type bead mill. The dispersion properties of silica sol have a close relationship to dispersion factors such as pH, milling time and speed, the size and amount of zirconia beads, the solid content of fumed silica, and the shape and diameter of the milling impellers. Especially, the silica particles in silica sol were found to show dispersion stability on a pH value above 7, due to the electrostatic repulsion between the particles having a high zeta potential value. The shape and diameter of the impellers installed in the bead mill for the dispersion of fumed silica was very important in reducing the particle size of the aggregated silica. The median particle size ($D_{50}$) of silica sol obtained after milling was also optimized according to the variation of the size and amount of the zirconia beads that were used as the grinding medium, and according to the solid content of fumed silica. The dispersion properties of silica sol were investigated using zeta potential, turbiscan, particle size analyzer, and transmission electron microscopy.

• 한국재료학회지
• /
• 제27권2호
• /
• pp.100-106
• /
• 2017

Nanosized and aggregated $Y_2O_3:Eu$ Red phosphors were prepared by template method from metal salt impregnated into crystalline cellulose. The particle size and photoluminescent property of $Y_2O_3:Eu$ red phosphors were controlled by variation of the calcination temperature and time. Dispersed nanosol was also obtained from the aggregated $Y_2O_3:Eu$ Red phosphor under bead mill wet process. The dispersion property of the $Y_2O_3:Eu$ nanosol was optimized by controlling the bead size, bead content ratio and milling time. The median particle size ($D_{50}$) of $Y_2O_3:Eu$ nanosol was found to be around 100 nm, and to be below 90 nm after centrifuging. In spite of the low photoluminescent properties of $Y_2O_3:Eu$ nanosol, it was observed that the photoluminescent property recovered after re-calcination. The dispersion and photoluminescent properties of $Y_2O_3:Eu$ nanosol were investigated using a particle size analyzer, FE-SEM, and a fluorescence spectrometer.

• 한국분말재료학회지
• /
• 제24권5호
• /
• pp.406-413
• /
• 2017

A Nanosized $WO_3$ and CuO powder mixture is prepared using novel high-energy ball milling in a bead mill to obtain a W-Cu nanocomposite powder, and the effect of milling time on the structural characteristics of $WO_3-CuO$ powder mixtures is investigated. The results show that the ball-milled $WO_3-CuO$ powder mixture reaches at steady state after 10 h milling, characterized by the uniform and narrow particle size distribution with primary crystalline sizes below 50 nm, a specific surface area of $37m^2/g$, and powder mean particle size ($D_{50}$) of $0.57{\mu}m$. The $WO_3-CuO$ powder mixtures milled for 10 h are heat-treated at different temperatures in $H_2$ atmosphere to produce W-Cu powder. The XRD results shows that both the $WO_3$ and CuO phases can be reduced to W and Cu phases at temperatures over $700^{\circ}C$. The reduced W-Cu nanocomposite powder exhibits excellent sinterability, and the ultrafine W-Cu composite can be obtained by the Cu liquid phase sintering process.

• 한국분말재료학회지
• /
• 제30권5호
• /
• pp.409-414
• /
• 2023

YSZ (Y₂O₃-stabilized zirconia)-based ceramics have excellent mechanical properties, such as high strength and wear resistance. In the application, YSZ is utilized in the bead mill, a fine-grinding process. YSZ-based parts, such as the rotor and pin, can be easily damaged by continuous application with high rpm in the bead mill process. In that case, adding WC particles improves the tribological and mechanical properties. YSZ-30 vol.% WC composite ceramics are manufactured via hot pressing under different pressures (10/30/60 MPa). The hot-pressed composite ceramics measure the physical properties, such as porosity and bulk density values. In addition, the phase formation of these composite ceramics is analyzed and discussed with those of physical properties. For the increased applied pressure of hot pressing, the tetragonality of YSZ and the crystallinity of WC are enhanced. The mechanical properties indicate an improved tendency with the increase in the applied pressure of hot pressing.

• 한국재료학회지
• /
• 제27권10호
• /
• pp.534-543
• /
• 2017

$Gd_2O_3:Eu^{3+}$ red phosphors were prepared by template method from crystalline cellulose impregnated by metal salt. The crystallite size and photoluminescence(PL) property of $Gd_2O_3:Eu^{3+}$ red phosphors were controlled by varying the calcination temperature and $Eu^{3+}$ mol ratio. The nano dispersion of $Gd_2O_3:Eu^{3+}$ was also conducted with a bead mill wet process. Dependent on the time of bead milling, $Gd_2O_3:Eu^{3+}$ nanosol of around 100 nm (median particle size : $D_{50}$) was produced. As the bead milling process proceeded, the luminescent efficiency decreased due to the low crystallinity of the $Gd_2O_3:Eu^{3+}$ nanoparticles. In spite of the low PL property of $Gd_2O_3:Eu^{3+}$ nanosol, it was observed that the photoluminescent property was recovered after re-calcination. In addition, in the dispersed nanosol treated at $85^{\circ}C$, a self assembly phenomenon between particles appeared, and the particles changed from spherical to rod-shaped. These results indicate that particle growth occurs due to mutual assembly of $Gd(OH)_3$ particles, which is the hydration of $Gd_2O_3$ particles, in aqueous solvent at $85^{\circ}C$.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2003년도 춘계학술발표대회 개요집
• /
• pp.102-104
• /
• 2003

Laser weldability of aluminized steels of 0.8mm thick has been investigated. Test materials were cut from the commercial steels that were produced at the Coating Mill of POCOS. Test coupons for welding were prepared by using a conventional shearing machine and no additional edge treatment was peformed. Nd:YAG laser welding system was mainly applied to make weld specimens. Test results revealed that almost no spattering was observed even though the welding was peformed with no overlap joint clearance. Bead quality of aluminized steel laser weld was smooth and stable. According to x-ray inspection results, it was proved that the laser welds of aluminized steels were metallurgically defect free.