• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.30 no.1A
• /
• pp.10-27
• /
• 2005

In this paper, we propose a high level design architecture of WCDMA(UMTS) base station modem and synchronization algorithms applied to the proposed architecture. Also analysis of each synchronization algorithm and performance evaluation of fixed point designed modem are shown. Since the target system is base station modem, each synchronization algorithm is designed for its stable operation. To minimize implementation complexity, optimum fixed point design for best operation of synchronization algorithms is performed. We performed symbol level link simulation with fixed point designed modem simulator for data rate of 12.2kbps, 64kbps, 144kbps, and 384kbps. We compared performance results to the minimum requirements specified in 3GPP TS 25.104(Release 5). Extensive computer simulation shows that the proposed modem architecture has stable operation and outperform the minimum requirement by 2 dB. The proposed modem architecture has been applied in the implementation of WCDMA reverse link receiver modem chip successfully.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.44 no.8
• /
• pp.9-16
• /
• 2007

Currently, the measurement of RF parameters for a base station in operation is typically limited to easily measured forward path items. In this paper, the forward monitoring ports of base stations are used to measure the reverse RF performance. The system has been implemented and effectiveness has been proven on an operating base station. The receiver sensitivity is measured using an internal CDMA modem which is used to monitor the output power based on closed loop power control when the modem is connected to the base station via a voice call. In order to improve accuracy, in addition to the modem Tx adjust(TxAdj) parameter, the detector's actual measurement is used. For accurate receiver sensitivity, the measurement should be made when there is no traffic which is not possible on an operating base station. Therefore, pilot channel chip energy to received signal power spectral density ratio$(E_c/I_o)$ compensation method is used to offset the receiver sensitivity degradation with voice traffic increase.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2001.10a
• /
• pp.307-310
• /
• 2001

In this paper we describe the design and implementation of uplink receiver for BWLL base station modem. The demodulator consists of digital down converter, matched filter and synchronization circuits. For symbol timing recovery we use Gardner algorithm. And we use forth power method and decision directed method for carrier frequency recovery and phase recovery, respectively. For the sake of performance analysis, we compare simulation results with the board implemented by FPGA which is APEX20KE series chip for Alter. The performance results show it works quite well up to the condition that a frequency offset equal to 4.7% of symbol rate.1

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.10 no.5
• /
• pp.921-927
• /
• 2006

The current DGPS technique is many problems that is permission of radio station using RF Wireless Modem, that is influence of geographic obstacle using radio wave, that is frequency interference, that is finiteness of frequency resources. In this paper, we are solved many elements, IM(Interface Module) replaces RF Wireless Modem, we suggest transmission technique of correction message using mobile phone, we researched Interface Module development which is linkage of DGPS receiver and mobile phone. IM can transmit correction message passing RS-232 port and modem communication control. IM of base station is initialized RS-232 port and modem to move station for correction message transmission, IM waited response mode. IM of move station is initialized RS-232 port and modem, IM requests hand shaking to base station, completed connection establishment. Users are worked Differential surveying using receiving correction message between mobile phones.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2002.05a
• /
• pp.197-200
• /
• 2002

The current Inn technique is many problems that is permission of radio station using RF Wireless Modem, that is influence of geographic obstacle using radio wave, that is frequency interference, that is finiteness of frequency resources. In this paper, we are solved many elements, IM replaces RF Wireless Modem, we suggest transmission technique of correction message using mobile phone, we researched Interface Module development which is linkage of DGPS receiver and mobile phone. IM can transmit correction message passing RS-232 port and modem communication control. IM of base station is initialized RS-232 port and modem to move station for correction message transmission, IM waited response mode. IM of move station is initialized RS-232 port and modem, IM requests hand shaking to base station, completed connection establishment. Users are worked Differential surveying using receiving correction message between mobile phones.

• ETRI Journal
• /
• v.19 no.3
• /
• pp.228-241
• /
• 1997

In this paper, we present a design of modem and vocoder digital signal processor (DSP) chips for CDMA mobile station. The modem chip integrates CDMA reverse link modulator, CDMA forward link demodulator and Viterbi decoder. This chip contains 89,000 gates and 29 kbit RAMs, and the chip size is $10 mm{\times}10.1 mm$ which is fabricated using a $0.8{\mu}m$ 2 metal CMOs technology. To carry out the system-level simulation, models of the base station modulator, the fading channel, the automatic gain control loop, and the microcontroller were developed and interfaced with a gate-level description of the modem application specific integrated circuit (ASIC). The Modem chip is now successfully working in the real CDMA mobile station on its first fab-out. A new DSP architecture was designed to implement the Qualcomm code exited linear prediction (QCELP) vocoder algorithm in an efficient way. The 16 bit vocoder DSP chip has an architecture which supports direct and immediate addressing modes in one instruction cycle, combined with a RISC-type instruction set. This turns out to be effective for the implementation of vocoder algorithm in terms of performance and power consumption. The implementation of QCELP algorithm in our DSP requires only 28 million instruction per second (MIPS) of computation and 290 mW of power consumption. The DSP chip contains 32,000 gates, 32K ($2k{\times}16\;bit$) RAM, and 240k ($10k{\times}24\;bit$) ROM. The die size is $8.7\;mm{\times}8.3\;mm$ and chip is fabricated using $0.8\;{\mu}m$ CMOS technology.

• ETRI Journal
• /
• v.19 no.3
• /
• pp.116-140
• /
• 1997

The base station transceiver subsystem (BTS) of the CDMA Mobile System is interfaced to mobile stations over the air and to the wired network through a packet switched interconnection network. The potential benefits of CDMA technology are achieved when the transmitter and the receiver are properly designed and implemented. The physical layer of the interface at the base station is implemented with the CDMA ASICs and control circuits in channel card of the BTS. We present the design perspectives and structural illustration of the BTS. Base station modem ASICs and their control to implement the CDMA receiver, Baseband and RF signal processing blocks, and BTS controller are described. Elaborate power control is essential to ensure the high capacity which is one of advantages of the CDMA technology. The closed loop reverse link power control and the forward link power control operated in the BTS are described.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.26 no.12B
• /
• pp.1677-1685
• /
• 2001

In this paper, we propose a call admission control scheme that can be performed within guaranteeing of required QoS(Quality of Services) in DS-CDMA(Direct Sequence-Code Division Multiple Access) reverse link. It has been performed rely on a physical channel numberonly and based on quality of received signal from MODEM(modulator/demodulator) part in established study. In other methods, the standard for services would have been set from statistical analysis of users\` location and using received power level in BTS(Base Transceiver Station). These ways bring about not only system loads but time delay or great differences from real environment. To solve these problems, we propose a call drop rate estimation algorithm for the purpose of call admission control based on measured value at LNA(Low Noise Amplifier) ports of BTS(Base Transceiver Station) in real time. This method proposed in this paper estimates a quality of offered service in real time, reduce system loads and shorten time delay which is needed to determine the standard for call admission control. But it requires a additional 17W complexity which can measure received signal power in BTS and estimate call drop rate.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.26 no.1
• /
• pp.122-127
• /
• 2022

Currently, the drone is considered as a mobile base station of USN as a method to act as a base station using USN in existing LTE-M and LTE networks for data transmission in unmanned ships. Therefore, the drone, which is a mobile base station, is a sink node equipped with an LTE modem or a short-range communication modem, and can collect safety information of ship operation from the sensor node and transmit the safety information to the ship or transmit the information between the ships. As, if a short-range network is formed by using drones, it will form a communication network around unmanned ships and will be advantageous for collecting information using security and environmental sensors. In this paper, we propose a method to transmit environmental sensor data and to utilize communication between ships using drones to secure the surrounding information necessary for AI operation of unmanned ships in the future.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.26 no.6
• /
• pp.617-624
• /
• 2008

In general, RTK-GPS(Real Time Kinematic GPS) based on the single reference station is able to determinate the high accurate position of rover on the spot using error correction information of transmitted carrier phase from the base station via wireless modem. However, single reference station method has some weak points to decrease positioning accuracy because it must be obtained carrier phase from the each satellite continuously, allowed to transmit without obstacle and limited to short base line distance between base and rover station. This paper aims to attempt network based GPS carrier phase differential positioning using three multi reference stations to overcome the method of single reference station and RTK network is realized by real time monitoring program with Visual C++. The optimum error correction value of three multi reference stations by RTK networking is selected automatically to correct the position of rover station. In this paper, this algorithm is applied to determine sea water level using GPS buoy, and the accuracy results of water level change were analyzed and compared with each other using single and multi reference stations.