• International Journal of Naval Architecture and Ocean Engineering
• /
• 제9권2호
• /
• pp.199-208
• /
• 2017

We perform an experiment on lacquer formation with simple test device. The anti-lacquer is one of important issues to increase durability, and to improve performance in the engines because the lacquer formation cause sticking of fuel injection pump, scuffing of cylinder liners, and increase of lubricant oil consumption in the marine diesel engines. We suggest this simple test in order to save enormous experimental cost in marine diesel engines, and in order to have ease in performing the various tests. The influences of the Base Number (BN) of lubricant oils and the sulfur content of fuel oils in the formation of lacquer are investigated. In order to investigate physical and chemical properties of lacquer, we perform a variety of tests such as, visual inspection, EDS. In addition, we investigate adhesion of lacquer by pull-off test quantitatively, and perform dissolution test with dilute sulfuric acid.

• Restorative Dentistry and Endodontics
• /
• 제18권1호
• /
• pp.27-37
• /
• 1993

The purpose of this study was to determine the fluroide release levels of new fluoride-containing liner/base cements and the fluoride uptake by dentin surfaces. Ten specimens of each brand (Fuji ionomer Type III, Fuji Lining LC, Timeline, Vitrebond and XR ionomer) were made, polymerized and placed in fluoride-free distilled water at $37^{\circ}C$, 100% relative humidity for 24 hours. The extracting solution of specimen was exchanged and fluoride release was measured daily for the 30 days. For fluoride uptake study, twenty-five extracted human lower molars were sectioned longitudinally in the mesiodistal direction with a diamond disc. Five teeth were filled with each material and then stored at $37^{\circ}C$, 100% humidity for 4 weeks. Fluoride uptake by dentin from the test materials was evaluated using electron probe micro X-ray analyzer. The following results were obtained : 1. The amounts of fluoride release showed no significant difference between Fuji ionomer Type III and Fuji Lining LC, but showed significant difference between other groups. XR ionomer released significantly greater fluoride than any other group(P<.001). 2. All the materials have a burst effect which more fluoride released in then first 3 day and showed significant decrease over the test period (P<0.001). 3. XR ionomer group showed fluoride penetration to approximately $50{\mu}m$ deep in dentin. But other material groups showed very little fluoride uptake by dentin.

• Journal of Advanced Marine Engineering and Technology
• /
• 제31권6호
• /
• pp.744-752
• /
• 2007

Recently a fuel oil of the diesel engine in the ship is being changed with low quality as the oil price is higher more and more. Therefore the wear and corrosion in all parts of the engine like cylinder liner ring groove of piston crown, spindle and seat ring of exhaust valve are increased with using of heavy oil of low quality In particular the degree of wear and corrosion in between valve spindle and seat ring are more serious compared to the other parts of the engine due to operating in severe environment such as the high temperature of exhaust gas and repeating impact. Thus the repair weld to the valve spindle and seat ring is a unique method to prolong the life of the exhaust valve in an economical point of view In this study. corrosion property of both weld metal zone and base metal was investigated with some electrochemical methods such as measurement of corrosion potential, cathodic and anodic polarization curves, cyclic voltammogram and polarization resistance etc. in 5% $H_2SO_4$ solution. in the case of being welded with some welding methods and welding materials to the exhaust valve specimen as the base metal. In all cases. the values of hardness of the weld metal zone were more high than that of the base metal. And their corrosion resistance were also superior to the base metal. The weld metal of A2F(AC SMAW: 2 pass welding with foreign electrode) showed a relatively good results to the corrosion resistance as well as the hardness compared to the ether welding methods and welding materials. Moreover it indicated that hardness of the weld metal by the domestic electrode was considerably high compared to that of the foreign electrode.

• Journal of Yeungnam Medical Science
• /
• 제37권3호
• /
• pp.169-178
• /
• 2020

Glass ionomer cement (GIC) is a tailor-made material that is used as a filling material in dentistry. GIC is cured by an acid-base reaction consisting of a glass filler and ionic polymers. When the glass filler and ionic polymers are mixed, ionic bonds of the material itself are formed. In addition, the extra polymer anion reacts with calcium in enamel or dentin to increase adhesion to the tooth tissue. GICs are widely used as adhesives for artificial crowns or orthodontic brackets, and are also used as tooth repair material, cavity liner, and filling materials. In this review, the current status of GIC research and development and its prospects for the future have been discussed in detail.

• 펄프종이기술
• /
• 제41권4호
• /
• pp.73-81
• /
• 2009

The document archives like official documents, books, maps and historic paper artifacts are primarily based on the organic cellulosic materials. As the passage of time, these organic cellulosic materials are slowly deteriorated by various aging factors, like light, polluted air and biological fungi. Many researchers have been carried out the examination method of deteriorating origins, the mechanism of aging hysteresis, and the preserving method of archival materials. One of the most simple and easiest ways for conservation of organic archival documents is the proper storage under environmental control. Corrugated board for archival quality container has been developed and already used in advanced country, like Japan, USA, German, UK and Europe. In case of Korea, corrugated board for archival quality container has been used a decade ago, but totally imported. This study was tried to develop the corrugated board for archival quality container. Liner and corrugated medium were specially produced and finally manufactured to E flute corrugated board. The physical and strength properties of permanent base paper and corrugated board were evaluated, and compared with imported corrugated board. 4 kinds of corrugating adhesives were considered various in order to investigate optimum adhesive for flute development between liner and corrugating medium, and evaluate adhesion strength under conditions of storage and curing temperatures.

• 한국토양환경학회지
• /
• 제1권1호
• /
• pp.103-109
• /
• 1996

일반 및 특정폐기물 매립지에서 복토층의 중요성은 매립지의 바닥층 만큼 강조되지는 않는 것 같다. 그러나 실제로 매립지의 파괴 원인중에 가장 커다란 영향을 미치는 것은 복토층 설치의 실패에서 온다고 볼 수 있다. 특히 복토층 기능은 우수를 지표면으로 유출증진하여 매립장 안으로 침투 억제시키며, 폐기물의 노출시 자연환경 위생에 대하여 완충작용을 하며, 매립지의 침하 및 침강을 억제하는데 있다. 본 연구는 겨울철 동결/융해에 따른 폐기물 매립지 최종복토의 거동을 수행하였으며, 폐기물 매립지에서와 같은 조건을 부여하기 위해 거대한 Lysimeter를 설치하여 실제로 최종복토에 쓰여지는 물질로 세가지 실험을 수행하였다. 실험결과는 동결/융해에 따른 점토층의 변화를 묘사하고 있으며 또한, 매립지에서의 동결깊이에 따른 복토층의 파괴는 점토의 물리 적, 공학적인 측면에 영향을 주며 이러한 영향은 매립지 설계시 고려되어야 한다고 본다. 본문은 실험에 사용되어진 복토층의 물질, 복토층의 묘사와 그들의 실험결과에 대한 결과분석 및 결론을 설명하고 있다.

• 대한치과보철학회지
• /
• 제37권2호
• /
• pp.200-211
• /
• 1999

For many years permanent soft denture liners has been widely used in dental practice directly or indirectly because of its function in absorbing and distributing the impact force. However, it reveals problems such as lack of permanency and decreased bond strength in long term use. The purpose of this study is to measure the bond strength and failure between denture base resin and several permanent liners. Lucitone 199 was used as denture base resin with soft acrylic liners (Triad, Tokuso Rebase) and silicone elastomers (Tokuyama, Ufi Gel C) bonded to measure the tensile strength before and after thermocycling. The thermocycling was done in 2000 cycles at $5^{\circ}C,\;26^{\circ}C\;and\;55^{\circ}C$ and the measured tensile strength values before and after thermocycling were compared. The mode of failure was investigated in the separated specimens. The results are as follows. 1. As to tensile strength, the strongest material is Tokuso Rebase followed by Triad, Tokuyama, Ufi Gel C in before thermocycling and the order of Triad, Tokuso Rebase, Tokuyama, Ufi Gel C in after thermocycling state. There was significant difference between the values of Triad, Tokuso Rebase and Tokuyama, Ufi Gel C(p<0.05). 2. As to degree of displacement, Ufi Gel C showed most displacement with or without thermo-cycling treatment and also the difference was significant with the other materials(p<0.05). 3. As to comparisons before and after thermocycling, Tokuso Rebase and Tokuyama showed significant difference in bond strength, whereas Triad and Tokuso Rebase showed significant difference in the degree of displacement(p<0.05). 4. In debonded specimens, Triad and Ufi Gel C showed adhesion failure and Tokuyama showed cohesion failure. Both failures were observed in Tokuso Rebase with adhesion failure up to 70%. The results of this study showed that degree of bond strength between permanent soft denture liner and denture base resin were variable. There was a significant difference between soft acrylics and silicone elastomers with regard to bond strength. Further research in improving bond strength of widely used silicone elastomers and in developing the method of measuring bond strength between denture base resin and the lining materials is needed.

• Restorative Dentistry and Endodontics
• /
• 제22권1호
• /
• pp.464-469
• /
• 1997

The radiopacity of glass ionomer cements is quite variable. The use of a poorly radiopaque material as a base under other restorative materials can mislead the dentist to a diagnosis of recurrent decay. This study investigates the radiopacity of these materials and proposes a minimal radiopacity under which a material should not be used as a base or liner. It is important to determine the radiopacity of glass ionomer dental materials so that the clinician can appreciate the type of restorative materials used when radiographically evaluation the possibility of recurrent dental caries. In this study, radiopacity of Vitrement and Chemfil was compared with that of Cavalite, Miracle mix and polycarboxylate cement. Tooth model of artificial cavity preparation for diagnosis of recurrent caries was omitted. Radiopacity of each material was measured using relatives between thickness and radiopacity of Aluminium step wedge. The results were as follows : 1. Radiopacity of Vitrement was some higher than enamel. 2. Chemfil, restorative glass ionomer, was less radiopaque than enamel. 3. In order of higher radiopacity than enamel, Miracle mix was highest and was followed by polycarboxylate cement, Cavalite and Vitremer. 4. Vitremer, the Glass Ionomer Cement, is useful to detection of recurrent caries, because it is slightly higher radiopaque than enamel. So, it is suitable for restorative material and luting cement.

• 한국군사과학기술학회지
• /
• 제16권4호
• /
• pp.553-559
• /
• 2013

We make several membranes with multilayer structure and characterize protective performance in various ways. Multilayer membrane is composed of shell fabric, support membrane, functional polymer membrane and liner fabric. In this research, we apply cellulose acetate derivatives as base polymer in functional polymer membrane and characterize water resistance, water vapor permeation, protective performance against DMMP and aerosol. Test results show that cellulose based polymer with polyethyleneimine possess performance with good water vapor permeation and excellent protective capability against DMMP equivalent to Saratoga type's protective suits. Also, these materials possess aerosol protective performance and water resistance.

• Tribology and Lubricants
• /
• 제31권3호
• /
• pp.86-94
• /
• 2015

We perform lacquer formation experiments with various combinations of marine fuel oils and lubricant oils. We also investigate the influences of base number (BN) in lubricant oil and sulfur content in fuel oil. A dissolution test with 10% dilute sulfuric acid and pull-off force test are accomplished to distinguish whether the residual layers are lacquering or not. The lacquering layers are dissolved by dilute sulfuric acid and have a strong pull-off force. Moreover, the calcium content detected in the residual layers is compared by energy dispersive x-ray spectroscopy (EDS). More calcium is detected in the lacquer layers than in other residual layers. Distillate fuels containing low sulfur levels are more prone to lacquering when mixed with lubricant oil with a high BN. On the other hand, residual fuels with a high sulfur content do not form lacquer. We investigate the effect of mixture volume ratio. The mixture with higher fuel oil content is more prone to generate lacquer. These experiments indicate that a lubricant with an appropriate BN should be used to prevent lacquer forming on the surfaces such as cylinder liners depending on the sulfur content of fuel oil.